Before the change, if the user wrote to any `tdata*` register, OpenOCD
would sometimes start to disable all the triggers (by writing zeroes to
`tdata1`) and re-enable them again (by witing all trigger registers to the
values read before for each `tselect` value), e.g. on `step`
(see `disable/enable_triggers()`).
There are a couple of issues with such approach:
1. RISC-V Debug Specification does not require custom register types
to support re-enabling by such sequence of writes (e.g. some custom
trigger type may require writing a custom CSR to enable it).
2. OpenOCD may still overwrite these triggers when a user asks to set a
new WP.
This commit introduces `riscv reserve_trigger ...` command to explicitly
mark the triggers OpenOCD should not touch.
Such approach allows to separate management of custom triggers and
offload it onto the user (e.g. disable/enable such triggers by setting up
an event handler on `step`-related events).
Change-Id: I3339000445185ab221368442a070f412bf44bfab
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Conflicts:
* `doc/openocd.texi`: due to d382c95d57,
resolved by selecting the upstream version.
* `src/server/gdb_server.c`: between
944fe66f10 and
92e8823ebd. Resolved by adopting the use
of `LOG_TARGET_*`.
* `src/target/target.c`: between
639e68a621 and
c5358c84ad, selected the version from
`riscv-openocd`.
Change-Id: Ic1327f25e147945e0ec82947a82452501e8ee5de
Remove list of id codes for all families.
Maintain a list with id, bscan-length and check position
in the tcl config files for each family.
The Intel FPGA Driver option 'family' is not otional anymore.
Change-Id: I9a40a041069e84f6b4728f2cd715756a36759c89
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/8083
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Probes all flash and UICR areas.
Flash erase and write tested.
On nRF53 mass erase works on the application core flash bank only.
The Tcl script nrf53_recover can serve as the workaround on the
network core.
TODO: mass erase of the nRF53 network core flash.
Some ideas taken from [1] and [2].
Change-Id: I8e27a780f4d82bcabf029f79b87ac46cf6a531c7
Link: [1] 7404: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/7404
Link: [2] 8062: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/8062
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8112
Reviewed-by: Tomáš Beneš <tomas@dronetag.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this functionality allows to query if a target belongs to some smp group
and to dynamically turn on/off smp-specific behavior
Change-Id: I67bafb1817c621a38ae4a2f55e12e4143e992c4e
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8296
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add minimal documentation for the BSCAN tunnel interface.
This is based on Tim Newsome <tim@sifive.com>'s work on
the RISC-V fork.
Change-Id: I5e0cd6972cb90649670249765e9bb30c2847eea6
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8297
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Conflict in src/rtos/FreeRTOS.c due to
fbea7d5d38 -- resolved by replacing
`target->type->name` with a call to `target_type_name()`.
Change-Id: I56702c6133894458903de7a4d764903004aa8b86
The link to product GW16042 was broken, so it has been reduced to
the manufacturer's website, which fixes the warning as a side effect.
The link to Raisonance RLink was broken, and the new one is shorter,
which fixes the warning as a side effect.
Change-Id: I4df9acf2d994d51cd8f375bdac6c803270029506
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8264
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To simplify the ipdbg start/stop command and be able to
add additional commands in the future, we introduce the
concept of a hub which has to be created before a
ipdbg server can be started.
The hub was created on the fly in previous versions.
Change-Id: I55f317542d01a7324990b2cacd496a41fa5ff875
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7979
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Add access to dsp registers and a command for dsp related operations.
Checkpatch-ignore: MACRO_ARG_REUSE
Change-Id: I30aec0b9e4984896965edb1663f74216ad41101e
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7867
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command substantially complicates support of nRF53/91
series. It was not even properly ported to nRF52.
The informative value is disputable. Who wants to see
e.g. override trim values for radio or unique device ID?
Drop it and simplify the driver.
Change-Id: Ia7fb20ce2ebf16065705c5d18deaf934e58db426
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add more debug messages connected with triggers.
Update names for internal flags to make them more clarified.
Change-Id: I5642346ce4a1e9bf79b22cdbf36bd757a7beffa8
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Prior to the change when calling `log_output` without any arguments it
was unclear where the log was redirected.
Change-Id: Iaa3ecea8166f9c7ec8aad7adf5bd412799f719a1
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8071
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enable support for USB vid and pid combinations other than 0x0403/0x6001
on OpenJTAG adapters.
Change-Id: Ibb5fb14a6f33abbc011dbf3179df20d79ed74a7a
Signed-off-by: N S <nlshipp@yahoo.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8100
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add detection for mips cpu types by using prid.
Add cpuinfo command for inspecting more verbose info.
Add MIPS Architecture specs in openocd docs.
Change-Id: I28573b7c51783628db986bad0e226dcc399b4fa6
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7912
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested with APM32F030C8T.
Change-Id: I63cd8b66424135dae481a96ba560e6f0b1f9544e
Suggested-by: Christian U <info@cu-tec.de>
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8014
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some devices with an internal multi-tap JTAG router require a vendor
specific bypass instruction to bypass the master TAP when addressing
slave taps internal to the same device. On these devices the standard
bypass instruction bypasses the whole device.
Change-Id: I4506f0e67c9e4dfe39b7fa18c63d67900313e594
Signed-off-by: Henrik Nordström <henrik.nordstrom@addiva.se>
Reviewed-on: https://review.openocd.org/c/openocd/+/8041
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If the remote_bitbang host does not execute requests immediately,
delays performed inside OpenOCD can be lost. This option allows
the delays to be sent to the remote host so that they can be
queued and executed in order.
Signed-off-by: Jeremy Herbert <jeremy.006@gmail.com>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Change-Id: Ie1b09e09ea132dd528139618e4305154819cbc9e
Reviewed-on: https://review.openocd.org/c/openocd/+/7472
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce 'cmsis-dap quirk' command to enable and
disable quirk mode.
If enabled, disconnect and connect before a switch
sequence and do not use multiple packets pipelining.
Change-Id: I6576f7de9f6c98a25c3cf9eec9a456a23610d00d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7966
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix the 'wp' command documentation.
Change-Id: I70f3110e8ce286051f8f810260f1857b2285e634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8022
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This is useful when using the SEGGER RTT tooling, as the SEGGER RTT
tool J-Link RTT Viewer version 7.84f requires that it receives a
messages immediately after connecting. Otherwise it will give a timeout
and it will not connect.
Change-Id: I9240a1b6a93cd5c0fbd18292afb33b89013d78bf
Signed-off-by: Thiemo van Engelen <tvanengelen@victronenergy.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7752
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Evgeniy Naydanov
Daniel Anselmi
Tomas Vanek
Parshintsev Anatoly
Tim Newsome
R. Diez
Marc Schink
Steven Chang
Walter Ji
Evgeniy Naydanov
Kirill Radkin
N S
ianst
David Vidrie Leon
Henrik Nordström
Jeremy Herbert
Karl Palsson
Manuel Wick
Thiemo van Engelen