Board config files, to allow communication with
the builtin USB-JTAG adapter.
Change-Id: I80fb0c36b3cc164940ff266f1eaa287d870da94d
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
ESP32-C6 and ESP32-H2 are single core riscv targets.
Change-Id: If92429de4fb67a040f303a54177d61b70e1ea281
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Change-Id: I825dd4fddb88e5514429d49ab13869ee6b9a28fc
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie3413d3149388b17bc0199409ce86d3eb7cf5ee2
Board config file for ESP32-S3, to allow communication with
the builtin USB-JTAG adapter.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1310f5db30f7df38fe9344f7ba2334611b53863e
Reviewed-on: https://review.openocd.org/c/openocd/+/7749
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This config file enables communication over USB-JTAG with
ESP32-C3, ESP32-S3, ESP32-H2 and ESP32-C6 chips
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Iceea26972588d8c4919d1f3248684ece48ca9121
Reviewed-on: https://review.openocd.org/c/openocd/+/7748
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ifb0122f3b98a767f27746409499733b70fb7d0e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I36c86fe4ebc99928ce48a5bff8cb9580a0fa3ac0
Reviewed-on: https://review.openocd.org/c/openocd/+/7746
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9181737d83eeba4e983b6a455b8a1523f2576dd2
Reviewed-on: https://review.openocd.org/c/openocd/+/7745
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Consolidate commonly used commands and variables from
chip config files into functions in esp_common.cfg.
This includes "jtag newtap," "target create,"and "configure -event."
Enhances code reusability and simplifies maintenance.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9e8bf07a4a15d4544ceb564607dea66837381d70
Reviewed-on: https://review.openocd.org/c/openocd/+/7744
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
They have an ir length of 22, 24 or 38 bit and different command codes.
Change-Id: I488e8613f1c4d017e1590111f60b2725ec62964b
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7387
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add missing ID codes and ignore the version in the ID.
Change-Id: Idd2d3a5eddb6995f3af1c45afd2adf76ce3442bf
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7386
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The old configuration files did not work because of a missing
'at91sam9260minimal.cfg' file. Also, the config files were placed
wrongly. Update them, put them to the proper location, merge the two
supported boards into one, remove now superfluous include, remove
defunct web page, etc.. Tested with a Calao USB-A9G20 and a hacked
'device_desc' to match. Native support for it will come next.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: Iec578c8777c5a6134e132dbac17c2988c7634742
Reviewed-on: https://review.openocd.org/c/openocd/+/7522
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With the new checkpatch we will not get this type of issues
anymore.
In mean time, let's fix what we have missed during the review
process.
Change-Id: Iecebf9d43f51a29ee09505d360792793afd24b40
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 53556fcded ("tcl/interface: add Ashling Opella-LD FTDI config files")
Reviewed-on: https://review.openocd.org/c/openocd/+/7530
Tested-by: jenkins
Use correct register name after it has beed changed
in commit 11ee500bff ("target/armv7m: Rename xPSR to xpsr")
Change-Id: I3648848f4b47af2d20d60c3e0ecef78f75f6d605
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7473
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It was fixed by e94180571 ("at91sam9: factorise cpu support") in 2011.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I95ea149b45a9902424bf9068b4a2830c17ddc6be
Reviewed-on: https://review.openocd.org/c/openocd/+/7525
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
in raspberrypi-native.cfg
Fixes: bec6c0eb09 (tcl/interface: universal config for all Raspberry Pi models)
Signed-off-by: Tomas Deingruber <Deingruber.Tomas@gmail.com>
Change-Id: I632c8acd84974937849b5fdf2943239def17bd6d
Reviewed-on: https://review.openocd.org/c/openocd/+/7512
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Integrate a rescue mode inspired by [1].
The current OpenOCD must be restarted before normal work with the RP2040
because the rescue debug port must not be activated (or the target
is reset every 'dap init'). To continue without restarting OpenOCD
we would need to switch off the configured rescue dap.
Change-Id: Ia05b960f06747063550c166e461939d92e232830
Link: [1] https://github.com/raspberrypi/openocd/blob/rp2040/tcl/target/rp2040-rescue.cfg
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7327
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Speed calibration coeffs are computed from cpufreq/scaling_max_freq
and from the device-tree compatibility information.
Raspberry Pi linux offers /dev/gpiomem for non-root access
to the GPIO registers since ~2016.
Do not configure 'bcm2835gpio peripheral_base' as it is necessary
only if /dev/mem is used - it requires running OpenOCD as root
- it's a security risk so it should be avoided.
The configuration of the GPIO connector (40-pin header)
is factored out and ready to use in interface configuration
for other driver (e.g. linux gpiod).
Mark raspberrypi2-native.cfg as deprecated and redirect
it to raspberrypi-native.cfg
Change-Id: Icce856fb660b45374e94174da279feb51f529908
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7264
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Same mechanism as in stm32f1x.cfg reused here.
Change-Id: I81f02feb2b655e8259341b22180f3a8b82e28d05
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7438
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The rtos hwthread has been merged in 2019 with commit 85ba2dc4c6
("rtos/hwthread: add hardware-thread pseudo rtos").
During review in patchset 19 the name of the rtos has been changed
from 'hawt' to 'hwthread'.
Some target config file was already merged ready for hwthread, but
keeping the relevant lines commented and still reporting the old
name.
Enable rtos hwtread to the target that were supposed to use it.
Fix the name of the rtos.
Change-Id: I877862dcdba39f26462bb542bac06d1a5f5f222d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7384
Tested-by: jenkins
This patch is picked from the tcl part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support the communication with Nuvoton's Cortex-M4 chips: M541 &
NUC442/472 series.
This patch has been tested with Nuvoton's NuTiny-SDK-NUC472 development
board [2].
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
[2]: https://www.nuvoton.com/export/resource-files/UM_NuTiny-SDK-
NUC472_EN_Rev1.02.pdf
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I27ac58dd1c98a76e791a4f1117c31060cf5522e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7330
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
rp2040-core0.cfg configuration file was intended for a special adapter
which selects a SWD multidrop target on its own. This means
that rp2040-core0.cfg is totally unusable with a standard SWD
adapter. The file was marked as deprecated in 0.12 release.
The reworked rp2040.cfg can be restricted to use just one core:
openocd ... -c 'set USE_CORE 0' -f target/rp2040.cfg
Remove the obsoleted config.
Change-Id: Id886471622bb4a8cb83f5c4c3660657407aaaf74
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7326
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add the variable selected configuration for SMP debug with rtos hwthread.
Use SMP by default.
Change-Id: I1c37d91688a3ab58d65c15686737892965711adc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7242
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.
To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.
Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
instrument "target/stm32x5x_common.cfg" used by both STM32L5x/U5x
to support HLA adapters like "interface/stlink.cfg" in non-secure mode
if the device switches to secure mode, the debug session will be
stopped immediately (with an explanatory message).
Change-Id: I645fdd55e3448ef82d0ddcc396f42fd7b2f39ac3
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Patrik Bachan <diggit@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/317/
Reviewed-on: https://review.openocd.org/c/openocd/+/6546
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Some config changes required to run ESP32-S3 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I38022bb5ff5830e1cf9d11d6fe795ea99d91e9db
Reviewed-on: https://review.openocd.org/c/openocd/+/7254
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tim Newsome
Erhan Kurubas
Daniel Anselmi
Julien Massot
Wolfram Sang
Antonio Borneo
Marc Schink
Tomas Deingruber
Tomas Vanek
Andreas Fritiofson
Zale Yu
Kyle Schwarz
Rocco Marco Guglielmi
George Voicu
Tarek BOCHKATI