IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
We have TCL procedure and commands that we do not want to show in
the list of auto-completion. E.g. TCL wrappers for deprecated
commands, internal procedures that are not supposed to be exposed
to user, or even commands that the user decides to hide.
Create a TCL procedure to be called by telnet auto-complete code
in place of the hard-coded TCL command. The procedure will run the
same command and will filter-out the unwanted command names.
Initialize the list of commands to be filtered-out with the name
of the TCL procedure above, as it is considered as internal.
Change-Id: I2d83bbf8194502368c589c85cccb617e69128c69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6194
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
this change aims to provide a better gdb debugging experience,
by making gdb understand what's really happening.
before this change when hitting a watchpoint
- openocd reports "T05" to gdb
- gdb displays: Program received signal SIGTRAP, Trace/breakpoint trap.
after the change
- openocd reports "T05watch:20000000;" to gdb
- gdb displays:
Hardware watchpoint 1: *0x20000000
Old value = 16000000
New value = 170000000
...
Change-Id: Iac3a85eadd86663617889001dd04513a4211ced9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6181
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Nowadays, when it's difficult to buy STM32F030,
the use of GD32F130 seems to be an interesting functional alternative.
This is cortex-M3 and it works with the stm32f1x driver, but unfortunately not fully.
The main difference is another offset of user option bits
(like WDG_SW, nRST_STOP, nRST_STDBY) in option byte register
(FLASH_OBR/FMC_OBSTAT 0x4002201C).
Any use of functions like lock or unlock results in change default values of the those bits stored in flash.
Thus broken microcontroller is malfunctioning, e.g. flash block programming is interrupted
by unexpected active hardware watchog (after 0.4s).
This patch is a simplified version of #4592 done by Dominik Peklo (http://openocd.zylin.com/#/c/4592/).
GigaDevice GD32F1x0 & GD32F3x0 series devices share DEV_ID
with STM32F101/2/3 medium-density line,
however they use a REV_ID different from any STM32 device,
so can be succesfully detected.
Change-Id: I252cdf738d94983b70676a3497326f90c329e292
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Reviewed-on: http://openocd.zylin.com/6164
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a use of AH_BOTTOM from configure.ac. This macro is used by
autoheader to add '#include' of some include file to the end of
config.h.in and then to config.h. OpenOCD can be built with a custom
config.h, so it's preferable to move these '#include' statement directly
in the C files that need them dropping this unneeded dependency.
It also causes problems when I want to use the gnulib library (which
comes with its own Makefile, and does not have the same include path as
the top-level Makefile).
So this change touches a lot of files, but is actually really simple. It
does not affect functionality at all.
Change-Id: I52c70bf15eb2edc1dd10e0fde23b2bcd4caec000
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/6171
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Currently, all drscan commands will cycle through DR-PAUSE before reaching
TAP-IDLE. This patch provides a different path on FTDI driver.
This change is required for the ST On Chip Emulator (OnCE), to avoid
re-enabling the OnCE tap after every DRSCAN. This is because the OnCE
TAP (see ST Application Note AN4035) gets disabled if DR-PAUSE is entered
before DR-UPDATE.
With this commit, the current path:
DR-SHIFT -> DR-EXIT1 -> DR-PAUSE -> DR-EXIT2 -> DR-UPDATE -> IDLE
is changed to:
DR-SHIFT -> DR-EXIT1 -> DR-UPDATE -> IDLE
only if IDLE is the endstate (which is the driver default).
Before this patch, once the SHIFT sequence is complete, the driver would
normally move to the nearest stable state, which is DR-PAUSE, by clocking
out a '10' binary sequence. Then it would follow the path provided by
tap_get_tms_path() to reach endstate. It is done this way because
tap_get_tms_path() only supports stable states.
After this patch, the strategy is mostly the same, with the exception that,
if TAP_IDLE is the endstate, a '110' binary sequence is output after completing
the SHIFT sequence. This takes the TAP directly to IDLE, with no further action
required.
A scheme of the DR chain is shown below. A * character is used to mark the
stable states.
----------------------------------------------------------------------
| | 0
v 1 0 0 1 0 1 1 |
IDLE* -> SEL-DR -> CAPTURE -> SHIFT* -> EXIT1 -> PAUSE* -> EXIT2 -> UPDATE
| ^
1 | |
-----------------------------
Change-Id: Ib413e5c4c0bbf75dae0b4672119bae4ef03d0258
Signed-off-by: Luis de Arquer <luis.dearquer@inertim.com>
Reviewed-on: http://openocd.zylin.com/6123
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
auto-completion behavior:
- if there is only one matched command complete the user-command
- else if multiple matches add the common part then in second step
list all matched commands
- sub-commands are handled in the same way
- auto-completion restarts after these characters ';', '[', '{'
Change-Id: I1b81dd19191a5785e68d0bb5cd244e01a4dd0587
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6095
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The documentation of Jim_SetResultFormatted() reports that the jim
objects passed as arguments would be freed if have zero refcount.
Remove the useless Jim_IncrRefCount()/Jim_DecrRefCount().
Remove the dangerous Jim_FreeNewObj() that should trigger a double
free(). Not tested due to lack of aice adapter.
While there, rename some CamelCase symbol.
Change-Id: Ic56704c83d6391c38f6b0efa6566784d453bc0fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6190
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 7a731eb637 ("Added HostOS variable"), merged in 2009,
adds a TCL global variable 'ocd_HostOS' that reports in a string
the OS of the host.
This was proposed as a workaround for jimtcl that didn't define
the standard TCL variable 'tcl_platform(os)'.
With commit 42f3fb7b7f46 ("Determine platform_tcl() settings with
configure"), merged in 2010 and part of jimtcl 0.70 issued in
early 2011, jimtcl provides the requires TCL standard variable
'tcl_platform(os)'.
The variable 'ocd_HostOS' has never been used by any TCL script
distributed with OpenOCD.
Drop the TCL variable 'ocd_HostOS'.
Change-Id: I27858de35cc9d30df97145ca1ccd24877be4af11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6189
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If malloc() fails, the just allocated Jim_Obj will leaks.
Move Jim_IncrRefCount() before the malloc() and deallocate the Jim
object with Jim_DecrRefCount() on malloc() fail.
While there, add the 'out of memory' log and fix the CamelCase
name of the symbol tclOutput.
Change-Id: Ic733db229d5aa5d477d758ea9cb88cd81d7542cd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6188
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The files jim-nvp.[ch] were originally inside jimtcl, then in 2011
they were dropped by jimtcl and integrated in OpenOCD.
The initial purpose was to make them as an independent library,
thus the presence of an 'init' function. Being now part of OpenOCD
do not require the 'init' function anymore, that is still empty
and unused, plus its name is in violation of the coding style.
Drop the function Jim_nvpInit().
Change-Id: I429e10444c86a26dbdc22aa071315324dc5edc3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6187
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Accordingly to OpenOCD coding style, both typedef and Camelcase
symbols are forbidden.
The type '_Bool' is not used in the code, having 'bool' as
preferred choice.
Remove the definition of '_Bool' from 'types.h'.
Change-Id: I8863f9836ccd9166e0c69fa5d75d6fef79ae7bfb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6186
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The ELF typedef's 'Elf32_Sword' and 'Elf32_Hashelt' are not used
within OpenOCD. Plus, being their name in CamelCase require extra
effort to include them in the exceptions for checkpatch.
Remove the unused typedef's.
Change-Id: I18f039567edd5b24dbb41df5406c154f31022ae7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6178
Tested-by: jenkins
Reviewed-by: Christian Hoff <christian.hoff@advantest.com>
The existing code asserted in that case, which is not correct. This
would allow the user to crash OpenOCD with a bad ELF file, which is
not what we want. A proper error should be reported in that case and
OpenOCD should not crash.
Change-Id: Ied5a6a6fd4ee0fd163f3fe850d304a121ecbe33a
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/6172
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Libusb defines both the struct and a typedef to the struct using
the same struct name. It's then possible to use either 'struct x'
and 'x'. E.g.:
typedef struct libusb_device libusb_device;
OpenOCD is not consistent and uses a mix of 'struct x' and 'x'.
To make OpenOCD code uniform, stick at project's coding style and
use 'struct x' in place of the typedef'd name.
Change-Id: I901458b680e42830d3f371e47997157f91b7f675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6165
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit a7d68878e4 ("helper/command: unregister commands through
their full-name") introduces for the first time in OpenOCD the use
of jimtcl API Jim_DeleteCommand().
The prototype of Jim_DeleteCommand() has changed with jimtcl 0.80
and the current code doesn't build with jimtcl 0.79 or older. This
is an issue for those distributions, like Debian, that provide
jimtcl as a separate package/library and have not switched yet to
the new jimtcl version.
Add a compile-time condition to cope with the jimtcl API change.
Change-Id: Ic813ab7c0ebd3c8772f27775ba3912a47d5c275c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: a7d68878e4 ("helper/command: unregister commands through their full-name")
Reviewed-on: http://openocd.zylin.com/6191
Tested-by: jenkins
Uses CMSIS-DAP v 1.2 or higher protocol command DAP_SWD_Sequence
to write to DP TARGETSEL register. This write is not acknowledged
by device so we cannot use standard DAP_Transfer
Change-Id: Ib252d09570bcc2282be5f854e0ab9a0dfda06189
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6117
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
Commit 246782229f ("smp: replace commands smp_on/smp_off with
"smp [on|off]"") deprecates some multi-word comments, when openocd
was unable to properly handle mixes of multi-word commands and tcl
procedures having a common initial word.
This limitation is over, so move in startup.tcl the multi-word
commands deprecation, making it easy to remove them after a grace
period.
Change-Id: Icb550d1fa7559b95692d2a1244880da6c90ec0b2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5677
Tested-by: jenkins
Windows socket descriptor is not file descriptor, so when
using remote_bitbang on Windows, it fails with "fdopen:
failed to open write stream".
This patch removes the file write stream, replaces it
with socket write calls.
Change-Id: Ifd7c8a4139a5ac51ecd2846835a7a947a90fe16c
Signed-off-by: Yun Liu <liuyun.97@gmail.com>
Reviewed-on: http://openocd.zylin.com/6096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some CMSIS-DAP adapters keep buffered packets over
USB close/open so we need to flush up to 64 old packets
to be sure all buffers are empty.
Flush just after cmsis_dap_open() and in the case of command mismatch.
Change-Id: If21a118639e64d90635b4ecf81013d29a7b9f78d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6135
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Check returned HID report number (or the first byte of returned
bulk packet) which should be equal to the issued command or 0xff
in case of the command is not implemented.
Fix error return paths in cmsis_dap_init() to clean up the adapter
connection.
Don't fail cmsis_dap_init() when an unimportant function fails
(for the case the adapter doesn't implement some parts of protocol).
Change-Id: Ief8382aabe9915346b2273702fb2ff17bbb5eb1b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6121
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
The function's name was consistent with its purpose to handle
commands that were not at root level, thus not directly 'known'
by jimtcl.
Rename it as jim_command_dispatch() to highlight that now it is
a jim_handler and its purpose is to dispatch the call to the
proper command handler.
Change-Id: I9491a6d6459b8eb37a6c402abcae08388c693764
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5791
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that all commands are executed through the common handler
command_unknown(), the message about command execution is logged
by command_unknown(). There is no need, for "native" commands
(.jim_handler) at root level to log the message (again) by itself.
Remove calls to script_debug() apart from command_unknown().
Make script_debug() static as only used in command.c.
Change-Id: I9b2728b69e7643d6121c4b35a96bc825bcb5488d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5676
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
There is no need anymore to keep alive the tree of struct command.
Remove it and let jim to free() the command's struct command that
is referenced through command's private data.
Change-Id: I2cd84e0274a969ce200320e3a177ac20c7823da0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5675
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While keeping the struct command in place, unregister the jim
commands by scanning the list of jim commands through their
full-name.
Change-Id: I0e903fbc31172858b703d67ccd471809c7949e86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5674
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that every command has struct command as private data, use jim
to get access to the struct command to read the command mode,
instead of running through the tree of struct command.
Change-Id: Iddacdbac604714f6abe38a050daad245bdcfd20c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5673
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that the commands are registered using their full-name, the
full-name is in argv[0].
Don't rebuild the full-name but use directly argv[0].
Change-Id: Ic9e469ac39276367b8c47527e70791ff470fefbc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5672
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While still keeping the tree of struct command, stop registering
commands in jim by the root "word" only.
Register the full-name of the command and pass as private data the
struct command of the command itself.
Still use the tree of struct command to un-register the commands.
Some "native" commands (.jim_handler) share the same handler, then
the handler checks the command name to run the right code.
Now argv[0] returns the full-name of the command, so check the
name by looking in the struct command passed as private data.
Change-Id: I5623c61cceee8a75f5d5a551ef3fbf5a303af6be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5671
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The current implementation of "help" related commands is tightly
connected to the tree of struct command.
The TCL commands 'add_usage_text' and 'add_help_text' have to add
fake commands in the tree of struct command to handle the help of
TCL procs.
Move all the help texts in a list accessible from the struct
command_context and register the commands through their full name.
Keep the list sorted alphabetically by the command name, so the
result of commands 'help' and 'usage' will be sorted too.
Remove the associated help and usage during commands un-register,
but call help_del_all_commands() for the text added through TCL
commands 'add_usage_text' and 'add_help_text'.
The resulting help and usage output is not changed by this patch
(tested on all the help and usage strings in current master
branch).
Change-Id: Ifd37bb5bd374cba1a22cd7aac208505b4ae1e6fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5670
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A tcl proc can be executed anytime, in any command mode.
Let the command "command mode" to detect a tcl proc and return the
string "any".
Change-Id: I0559076c3063632ee0ea9a57a25f91060209b77f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5669
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Replace the "struct command *parent" parameter with a string that
contains the command prefix.
This abstracts the openocd code from the knowledge of the tree of
struct command.
This also makes unused the function command_find_in_context(), so
remove it.
Change-Id: I598d60719cfdc1811ee6f6edfff8a116f82c7ed6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5668
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In current code the current target is overridden whenever
jim_handler_data is not NULL. This happens not only with target
prefixed commands, but also with cti, dap and swo/tpiu prefixed
commands.
While this is not causing any run-time issue, by now, the
behaviour is tricky and makes the code cryptic.
Add a specific field to struct command for the target override so
the content of jim_handler_data can be restricted to command
specific data only (today only cti, dap and swo/tpiu).
Extend the API register_commands() to specify the presence of
either the command data or the override target.
The new API makes obsolete calling command_set_handler_data() to
set jim_handler_data, so remove it.
Change-Id: Icc323faf754b0546a72208f90abd9e68ff2ef52f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5667
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that target override is uniformly implemented for all types of
commands, there is no need for target-prefixed "native" commands
(.jim_handler) to sneakily extract the overridden target from the
struct command.
Modify the commands to use the standard API get_current_target().
Change-Id: I732a09c3261e56524edd5217634fa409eb97a8c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5666
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Today openocd registers the commands to jim with three methods:
1) "native" commands (.jim_handler) at root level are registered
directly as jim commands;
2) "simple" commands (.handler) at root level are registered
through the handler script_command();
3) all other commands not at root level are registered through the
handler command_unknown().
Apart from using different handler, other inconsistencies are
present:
a) command in 1) are not checked for their "mode", so are run with
no check about current mode (COMMAND_CONFIG or COMMAND_EXEC);
b) target_call_timer_callbacks_now() is called only for "simple"
commands and not for "native" commands;
c) target override is performed only for "simple" commands and not
for "native" commands.
Drop script_command() and extend command_unknown() to uniformly
handle all the cases above, fixing all the inconsistencies already
mentioned.
The handler's name command_unknown() is probably not anymore
appropriate, but will be renamed in a separate change.
Note: today all the commands in a) have mode CONFIG_ANY, apart for
"mem2array" and "array2mem" that have mode COMMAND_EXEC. But the
latter commands are registered during target init, so do not exist
during COMMAND_CONFIG and no issue is present.
Change-Id: I67bd6e47eb2c575107251b9192c676c27d4aabae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5665
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While registering a new command, jim accepts a pointer to command's
private data that will be accessible during the command execution.
Today openocd is not consistent and passes different private data
depending on the command, and then even overwrites it:
- "simple" commands (.handler) are registered with their own
struct command pointer as command private data;
- "native" commands (.jim_handler) at root level are registered
with NULL command private data;
- "native" commands (.jim_handler) not at root level are
registered with the struct command pointer of their root command
as command private data but, when executed, the command private
data is overwritten by the value in field jim_handler_data taken
from their struct command.
Uniform the usage of command private data by always set it to the
struct command pointer while registering the new commands.
Note: for multi-word commands only the root command is registered,
so command private data will be set to the struct command of the
root command. This will change later in this series when the full-
name of the command will be registered.
Don't overwrite the command private data, but let the commands that
needs jim_handler_data to get it directly through struct command.
For sake of uniformity, let function command_set_handler_data() to
set the field jim_handler_data also for "group" commands, even if
such value will not be used.
Now Jim_CmdPrivData() always returns a struct command pointer, so
wrap it in the inline function jim_to_command() to gain compile
time check on the returned type.
While there, uniform the code to use the macro Jim_CmdPrivData()
to access the command's private data pointer.
Change-Id: Idba16242ba1f6769341b4030a49cdf35a5278695
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5664
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
If current core is in EL0, it cannot use 'msr sctlr_el1, x0'
Change-Id: I04e60e39e4c84f9d9de7cc87a8e438f5d2737dc3
Signed-off-by: Cheng-Shiun Tsai <cheng.shiun.tsai@gmail.com>
Reviewed-on: http://openocd.zylin.com/6051
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The target mem_ap is a convenient way to access buses, memory and
peripherals behind an ARM AP.
The current implementation provides only access through OpenOCD
commands, because GDB remote protocol has to interact with a CPU
and has to operate on CPU states and registers.
Using GDB to access the memory is welcome, because GDB can resolve
the symbol's address from an ELF file and can nicely display the
content of complex struct and data types.
Extend mem_ap target with the bare minimal support for a remote
GDB connection, by emulating a fake basic ARM core. It means that
only a GDB that has support for ARM can be used (either 'aarch64',
'arm' or 'multiarch' GDB). This is not seen as a big limitation,
because the mem_ap target is mainly used on ARM based devices.
Add a minimalist register description for the fake CPU.
Fill the field 'debug_reason' as expected by GDB server.
Call the target halted event to reply to GDB halt requests.
For backward compatibility, don't open the GDB port by default. If
needed, it has to be specified at 'target create' or 'configure'
with the flag '-gdb-port'.
Change-Id: I5a1b7adb749746516f5d4ffc6193c47b70132364
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6034
Tested-by: jenkins
There are some breakpoint/watchpoint related code in armv8_dpm.c,
but seems not working for aarch64. Target aarch64 has its own
breakpoint implementation in aarch64.c. This commit follows the
same logic to add watchpoint support for target aarch64.
This commit also increases the size of stop_reason[] in function
gdb_signal_reply() since the old size is too small to fit in a
64-bit address, such as ffff8000115e6980.
Change-Id: I907dc0e648130e36b434220f570c37d0e8eb5ce1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/4761
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Kevin Burke <kevinb@os.amperecomputing.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Each one of CMSIS-DAP command handlers was responsible for setting
HID report number, which in case of USB bulk transport was not used
at all. The command had to be filled with 1 byte offset whereas
the response was read without an offset.
Introduce 'command' and 'response' pointers into struct cmsis_dap.
Use them for filling the command and read the response respectively.
CMSIS-DAP command parameter are now at positions as documented in
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__Commands__gr.html
Adjust buffer allocation for HID and USB bulk transports.
While on it, use h_u32_to_le() and h_u16_to_le() instead of per-byte
writes.
Change-Id: Ib0808d6826ba0e254c1007ace8b743405536332a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6120
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The hidapi cmsis-dap backend is using a packet_size of
64+1: 64 is the bMaxPacketSize0 and 1 is the hid Report-Id.
In hidapi::hid_write(), the packet_size is decremented by 1 and
stored for the next transfer.
The packet_size is now valid bMaxPacketSize0=64,
so when hid_read() is called, libusb_bulk_transfer() finishes w/o timeout.
For the libusb bulk backend, the same packet_size of 64+1 is used,
but there's no hid_write() to decrement and store it for the next read.
So the next time a read is done, it will try to read 64+1 bytes.
Fix this by putting the packet logic within each backend.
Use calloc() to allocate the struct cmsis_dap to be on safer side.
Change-Id: I0c450adbc7674d5fcd8208dd23062d5cdd209efd
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5920
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Now that the old drivers have been converted to libusb1, there is
no need to keep the build dependency from libusb0.
Drop libusb0 from configure and makefiles, remove the libusb0
helper and remove libusb0 and libusb-compat from the README files.
Change-Id: Icc05be74ae5971ba6cbb67d39107c709a4d826e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5993
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: Idef0b6cf10fab583bc8d13b3b4fadd5cc368c090
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5990
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: I3f334f2d02515d612097955e714910a587169990
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5992
Tested-by: jenkins
The API Jim_CreateCommand() in latest version of jimtcl leaks the
memory allocated internally by jimtcl when it converts the string
command-name to a Jim_Obj.
The fix is already merged upstream and would be available in next
jimtcl 0.81, expected in ~6 months, hopefully before the next tag
for OpenOCD v0.12.0.
OpenOCD v0.11.0 is distributed with jimtcl 0.79.
Debian distributes jimtcl as a separate library package and today
it's still on 0.79.
It make sense to keep using jimtcl 0.80 in current development
cycle to test it further. But having this background memory leak
noise hides the eventual new memory leaks that could come from the
development activity.
This patch uses the internal jimtcl API Jim_CreateCommandObj() and
correctly free the internal object, avoiding the memory leak.
Being an internal API, it is not accessible if OpenOCD is linked
with an external jimtcl library. Nevertheless, building jimtcl as
a submodule of OpenOCD makes the trick effective.
The scope of this patch is thus limited at developers that build
OpenOCD with jimtcl submodule and need to control and debug memory
leaks.
This patch is supposed to be removed as soon as jimtcl 0.81 gets
available.
The added code is located, on purpose, in an area of the file that
hopefully will not conflict other patches pending in gerrit.
Change-Id: I4d300ad21bdb6c616c3f0f14b429b4fdf360900d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
After bootstrapping build, if we want to do an out-of-tree build (ie: in the
OOT-build dir) we have a build failure because build system relies on
the OOT-build/src directory exists
```sh
./bootstrap
mkdir OOT-build
cd OOT-build
../configure --disable-dependency-tracking --<flag1> --<flag2> ...
make
$ LANG=C make
cat ../src/helper/startup.tcl ../src/jtag/startup.tcl ../src/target/startup.tcl ../src/server/startup.tcl ../src/flash/startup.tcl | ../src/helper/bin2char.sh > src/startup_tcl.inc || { rm -f src/startup_tcl.inc; false; }
/bin/bash: line 1: src/startup_tcl.inc: No such file or directory
make: *** [Makefile:6603: src/startup_tcl.inc] Error 1
```
These kind of errors are fixed indicating relevant directory creation in
Makefile.am before actually relying on it.
Change-Id: I8185fd41ef942184597dc4c0092796034572cbe1
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6106
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduction of 'enum stm32l4_rdp' enumerating possible RDP levels for
devices with and without TrustZone.
also in 'stm32l4_flash_bank' structure we added and rdp and tzen members
to store read values by the helper 'stm32l4_sync_rdp_tzen'
these new members are used to display security and protection status
while probing the flash.
Change-Id: Icf883189715278a3323fe210d295047678b16592
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5541
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In flash/nor/cfi.c:835 struct cfi_info is allocated by malloc(). As
write-mem was uninitialized the pointer pointed to an out of range
address, which led to a segmentation fault and crashed openocd.
This happened during flash-command of an external flash-bank, using
cfi.
Use calloc() instead.
While on it check for NULL return and remove unnecessary initialzation.
Change-Id: I0e2ffb90559afe7f090837023428dcc06b2e29f6
Signed-off-by: Mischa Studer <mischa.studer@csa.ch>
Reviewed-on: http://openocd.zylin.com/6070
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In case of some error, the USB device and firmware file are still
claimed. Make sure refcounting is properly accounted for both cases.
Change-Id: I933114f68e59280e58372c0941a0062fe96ab340
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/6115
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If not, multiple instances of OOCD can concurrently use it.
Change-Id: I48cc9d90521d1dcc7720c6e8bec74f45972d16f7
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4589
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For Zephyr rtos support it is necessary to define general register
numbers for architecture. There were some already in arc.h file.
Let's define ARC registers numbers as a set instead of separate defines.
Change-Id: I63742b8608f9556c2ec9bd2661a0fd9cf88e9b74
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/6105
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This removes some warnings which prevent a successful build with -Werror
which is enabled by default. I'm using gcc 11, so maybe others are not
getting this warnings yet.
In src/flash/nor/numicro.c the debug messages were misleadingly indented.
In src/target/arm920t.c the array size where smaller than expected from
the receiving function.
Change-Id: I66f5c6a63beb9f9416e73b726299297476c884d8
Signed-off-by: Rene Kita <git@rkta.de>
Reviewed-on: http://openocd.zylin.com/6104
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this will help navigate to the line start and end easily
Change-Id: I3f42eb5267df64c59a85ece67de5fce39a8843ec
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6094
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Support halting the CPU directly after a reset. If halt is
requested, the CPU stops directly at the reset vector, before
any code is executed.
This functionality was implemented using the Reset Catch
debug event.
Change-Id: If90d54c088442340376f0b588ba10267ea8e7327
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/5947
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
With zy1000 removed, there is no other implementation that uses
the minidriver, apart from the test/example minidriver-dummy.
While the idea of the minidriver is probably still valid (that is
to intercept jtag primitives before serialization), there is no
current use case, no guarantee it is really working, and the way
it was implemented (by macros and #if conditionals) is really hard
to maintain and test.
Let's let it rip in git history, from where it could eventually be
taken back in a more modern implementation.
The entry points of minidriver API are still in the code with the
original names.
Change-Id: I882e32cb26cf5842f9cba14e3badaf8948e3760d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6091
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The code for ioutil has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I36dce1669ebe9acada5f9e752835c53e5214e3be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6089
Tested-by: jenkins
The code for oocd_trace has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I989f8345dee4ff2369bcf5e2e2ace86bbd5aa6a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6088
Tested-by: jenkins
We do not have anymore any deprecated target name.
Drop the code to handle deprecated target names and the placehold
in struct target_type.
This patch is separated from the patch that drops the remaining
deprecated target names to be ready to revert this if there is any
need in the future.
Change-Id: I96fca7ffa39d8292f81e79f115ea45c4a30035d7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6087
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some target name were marked as deprecated in release v0.7.0 and
v0.8.0, almost 7 years ago, and replaced with more 'actual' names.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.8.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the target names already deprecated in v0.8.0.
Change-Id: I7c7491496db1b302b4eb1e9fc6090b58d4acf05a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6086
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OpenOCD command line flag -p/--pipe was marked as deprecated
in release v0.5.0, more than 9 years ago.
We can reasonably expect that in these 9 years any user of OpenOCD
has already migrated to v0.5.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the command line flag already deprecated in v0.5.0.
Change-Id: I2faeb592ed2c2f67c2d3227f118093e39fcf4a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6084
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm920t cp15i' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I755c4283e13e125558fcd73b15fe20498eae95ca
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6083
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm720t cp15' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I2b325d0312d96ca5e5f0f1bad13bb162b3b75c52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6082
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is specially needed when, in the probe routine, device is not
found among the stm32l4_parts. In this case, the stm32l4_flash_bank->part_info
is undefined and inadvertentanly used afterwards:
part_info = stm32l4_info->part_info;
If the stm32l4_flash_bank is zero init, the probe routine checks for
the validity of the part_info field in the previous struct and correctly
detects the unsupported (or not found) condition, raising an error
rather than a SIGSEGV
Change-Id: I7d9d669fb3fa7f8f0903acd60046966b4acb0031
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6103
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no good reason to use macros instead of static inline functions. The
current code is hard maintain. For example, it changes variables outside of the
macro scope. Also, it is conflicting with the C coding style.
Change-Id: I5ac9d2ae076ef73c176d4e32b2e7e0a99fa875ab
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6046
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The buffer passed to stlink_usb_trace_read() is allocated of size
*size and does not need to be zero-terminated. There is no reason
to not fill its last byte.
When checking the bytes available on swo, limit the retrieved byte
length to *size.
Change-Id: Iade0f8963118695931f13a8a3f1ab204911236b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6061
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Missing the space cause the hex value to be printed together with
the following field.
Add a space after PRIx32.
Change-Id: I95824a9a8b8c0ad911d6c31f732d926cb3e0c068
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6060
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
With the removal of old tpiu code, commit 7e6556b3ca ("server:
permit the add_service function to return the created service")
http://openocd.zylin.com/5717/ can be reverted.
Fix also the new calls to add_service().
Change-Id: Ib7f2dfc6a9e829239e20313e0f121911085fdc00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6031
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
This is supposed to replace big part of armv7m_trace.[ch], since
TPIU is not only the one implemented in Cortex-M3 and M4.
Change-Id: I7588d16cbefe9cdb371c52fb0aa5cdfb48518804
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5858
Tested-by: jenkins
If the command 'itm port[s]' is issued before 'init', the ITM can
not be programmed because OpenOCD cannot access the target yet.
The configuration is recorded and applied after target examine.
The current test to trigger the ITM delayed-programming is based
on the TPIU configuration. This is allowed because the only use of
ITM it so send data through TPIU.
In case of system TPIU, not belonging anymore to the target, there
is no more association between target ITM and system TPIU.
Add a flag to record the pending ITM configuration requested
before 'init' and test the flag to trigger the delayed-programming
of the ITM.
Change-Id: I101eb97a116d7925cd2ff068f3e8813fc008b08e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6029
Tested-by: jenkins
The change [1] guarantees that the value pointed by 'prescaler'
gets always set, even when the adapter does not support the
specific mode requested (e.g. sync), or during trace disabling.
This works fine with the code in armv7m_trace_tpiu_config(), but
requires all the parameters to be valid also to disable the trace
(with 'enable==false'), otherwise returns error on incorrect
parameters or even causes segmentation fault if pointers
'trace_freq' or 'prescaler' are NULL.
Another problem in stlink_config_trace(), not linked with [1], is
caused by a tentative to change the settings on an already enabled
trace; the trace is disabled before the new parameters are fully
validated and in case of invalid parameters the trace is not
re-enabled.
It would be more logical to first check all the parameters, then
disable the trace, change the settings and re-enable the trace.
Practically revert [1] by checking 'enable==false' at function
entry, then disable trace and exit without any further check on
the other parameters.
For the case 'enable==true', validate all the function parameters
then disable the trace, update the trace settings and re-enable
the trace.
Modify the caller armv7m_trace_tpiu_config() to initialize the
variable 'prescaler' to a safe value to avoid the issue targeted
by [1].
[1] commit 38277fa752 ("jtag/drivers/stlink_usb: fix SWO prescaler")
Change-Id: Ia6530682162ca2c9f5ac64301f2456f70cc07ed2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5934
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Convert the driver from libusb0 to libusb1.
Change-Id: I17d14522db18b4050d462d23151ec97d3a315a7f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5991
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
pg315 of CoreSight Components:
It is recommended that the ITMEn bit is cleared and waits for the
ITMBusy bit to be cleared, before changing any fields in the
Control Register, otherwise the behavior can be unpredictable.
Change-Id: Ie9a2b842825c98ee5edc9a35776320c668047769
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6043
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target->endianness is initialized to TARGET_ENDIAN_UNKNOWN at 34 lines
below, before calling target_configure. This initialization is
redundant and not needed.
Change-Id: Iea2d5e17a13c1a8b0b209ba7c20043736b520ef6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tarek BOCHKATI
Marc Schink
Daniel Anselmi
Antonio Borneo
Peter Lawrence
asier70
Tim Newsome
Luis de Arquer
Christian Hoff
Florian Meister
Tomas Vanek
Yun Liu
Cheng-Shiun Tsai
Liming Sun
Adrian Negreanu
Raúl Sánchez Siles
Mischa Studer
Oleksij Rempel
Evgeniy Didin
Rene Kita
Yasushi SHOJI