added "Single Wire Output" and "Trace Memory Controller" peripheral
IDs to dap_rom_display(), which is invoked by the "dap info" command
Change-Id: Iea3201007bb98e6376fbb50be40a4a2e031b0a03
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When looking for a debug base address of a core, one should search
through all the ROM tables, not just the top-level one.
This code also assumes that the first found entry (in a depth-first
search) will correspond to core 0, the second to core 1 etc.
The patch is supposed to be an alternative implementation of
http://openocd.zylin.com/#/c/1313/.
Change-Id: Ifc88971a02fe3d9c00d9bf72a822ade5804d4e09
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code treats registers that are shadowed in FIQ mode in a special
way: to read them out the target is first switches to USR mode. But
since USR != ANY the current implementation later skips register read,
and the loop becomes endless in case any !valid ARM_MODE_ANY is
present at the moment arm_dpm_full_context() is called. This was
reported in https://sourceforge.net/p/openocd/tickets/76/. The issue
surfaced because 2efb1f14f6 added two
ARM_MODE_ANY registers ("sp" and "lr") which were not normally read,
so at the time a user was calling "arm reg" they were not valid.
Fix this by changing the mode appropriately while keeping the "mode"
variable state intact so it would later match register's mode.
Compile-tested only.
Change-Id: I01840e8fa20ec392220138a3f1497ac25deb080a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
This was very helpful when debugging programs during async loading.
Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Using custom build-time tools is always more problematic, especially
for cross-compiling.
This alternative implementation assumes "od" (IEEE Std 1003.1-2001)
and sed are available which should be the case for any reasonably
modern system.
Change-Id: I0208f475648c78e7dca127ff4bab60d314b2bf53
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2139
Tested-by: jenkins
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If load_image address overlap with fast_data_area,
it will caouse different mysterius issues. This patch
should prevent it.
Change-Id: Ibc95e5aa3ac002a59755029496b6a72616e9287f
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1854
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A previous commit changes the target name used by tcl scripts.
commit d9ba56c295
target: rename cortex_a8 to cortex_a
The current change renames target functions and definitions in the
implementation from cortex_a8 to cortex_a.
This prepares the implementation to support Cortex-A8, A9, A15-MPCore
in one place.
Change-Id: I73b5a38a92c12ba5bd3b806fbbb664817575a6d7
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1599
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Polling was disabled based on global variables jtag_trst and jtag_srst
which were never touched in non-JTAG mode. Modify the check and remove
the ugly workaround to avoid calls to a possibly uninitialized JTAG
subsystem.
Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2143
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also align them with spaces instead of tabs.
Change-Id: I1c01412a3ea77b29e8e133f5c92d05ed79d7c0f3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2133
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only
setting that is guaranteed to be implemented, as well as being the reset
value in ADIv5.0.
Thus it makes no sense supporting anything else.
Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2132
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Name of the function is already a part of the LOG_DEBUG macro, so
there's no need to include it in the string itself.
Change-Id: I18c3d5b746e9106d55104e490ccf5bc5e85cc380
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2138
Tested-by: jenkins
SAM4L requires additional steps to be taken right after SYSRESETREQ is
issued in order to function robustly:
- CMSIS-DAP DAP driver needs to explicitly check for sticky bit
errors since it is possible for adapter to perform successful
write opration, report no errors and then, under the hood, do
some other things that will result in sticky bit being set.
- Debugger needs to wait for security system to finish
intialization and assert CDBGPWRUPACK before proceeding
This change is related to commit http://openocd.zylin.com/#/c/1995/
Change-Id: I741c95a809bfd60d930cec9482239e4796a62326
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2088
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
We don't need to do full blown AP ABORT in case of CMSIS-DAP errors,
and the code that was in place was not doing that(issuing AP ABORT)
anyway.
Change-Id: Ide83b1f8875d725da6cb0d53aae8229f8c6316b3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2112
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Swd_queue_ap_abort should set DAPABORT, not only clear sticky errors.
However, DAPABORT should not be set as soon as there is a single
FAULT/WAIT response. It's an "emergency only" operations for use only when
the AP have stalled the transfer for a long time. So these need to be
separate functions.
Change-Id: I37618447884faad54d846c2b07fa668ad505919d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1956
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These features are not currently used so remove or disable them before
something starts to. Not having them around simplifies redesign of the
APIs.
Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1955
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Increases performance by a factor of two for long reads.
Change-Id: I81a7a83835058560c6a53a43c3cc991100f01766
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1954
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Otherwise it breaks SWD targets. The check seems really weird anyway since
it loops through *all* TAPs after the ADIv5 target but doesn't do anything
at all with the result, other than not setting the return values despite
returning ERROR_OK.
Remove a bogus initialization that was needed because of the odd
behaviour of this routine when an IDCODE wasn't found.
Change-Id: Ic086352f6af868b3406b00420291a0a671e3acac
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1953
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix bug in parity calculation macro.
Cache and update the selected DP bank when necessary.
Add aborts when the Ack code signals a failure (we should really only
clear the sticky bits, but this will do for now).
Change-Id: I38a4da136ba1d9e989b33c1875a80c0b1b2be874
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1950
Tested-by: jenkins
while investigating coresight components, i've found some new partnumbers and devtypes.
Change-Id: Ie68032b0b21d542c2084f80db38b06f5cd4c7591
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/2166
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On a processor with caches, when you write data to memory OpenOCD invalidates
the cache lines affected. If you write to an address within 64 bytes of
UINT32_MAX, then the for loop control variable wrapped around resulting in an
infinite loop. Change control variable to be an offset from the address
involved. We should never be asked to write 2^32 bytes, so wraparound should
not be a problem.
Change-Id: Ibfe654113eff71684862ff651e7a1cd05ccc6760
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2126
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We don't need to swap the endianness in the target generic code.
This swap is necessary because of the adv_debug_if debug unit.
This patch moves this specific piece of code from or1k.c to
or1k_du_adv.c.
Change-Id: I3acea092fe6edfa79b4a87861b5f01204f071bf0
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1663
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
ARMv7-R cores are largely uniprocessor-configured, and when they are
multiprocessor-configured the format of the MPIDR register isn't
compatible with ARMv7-A cores.
Change-Id: I024ec514496fbab5075c6fb34b6acd870e68e1fc
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2096
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Configuration commands assume the last created target is the one they
should be applied to. An example of this is sourcing an stm32f1.cfg
several times to access several microcontrollers on the same JTAG chain
where cortex_m reset_config should apply to the target that was just
created, not to the first one.
This fixes http://sourceforge.net/p/openocd/tickets/71/ .
Change-Id: I1ca41cc05fe5f36c4bc62dde4614da1405754fd8
Reported-by: Michael Eischer <mieischer@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2142
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If polling was failing, it likely meant that either the target was
disconnected or rebooted. In the latter case it needs to be reexamined
to be properly configured for the debug session, so do it just in
case.
Reported-by: Tim Sander <tim@krieglstein.org>
Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I5b067c18d9276d4e86cc59739f196ae7d0931622
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2151
Tested-by: jenkins
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move logging for cmsis_dap_queue_ap_read/write to happen after a call
to cmsis_dap_ap_q_bankselect so that that SWD operation would appear
in the log in the same sequence they happen on the bus.
Change-Id: Ic046bc753e661da7924b019c9100d6932fb686bf
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2087
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Previous to this commit 'ahbap_debugport_init' would ignore if timeout
happened or not when waiting for CDBGPWRUPACK and CSYSPWRUPACK and would
continue initialization regardless. It also would not reset the
timeout counter after finishing polling for CDBGPWRUPACK and starting
for CSYSPWRUPACK which could potentially cause some problems.
Also refactor code of both snippets into a more generic function to
avoid duplication.
Change-Id: I16e4f50e6819e08c4126e71ef8cec7db559d608e
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2086
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Fix for LOG format specifiers, this is a superset of those
exposed by the arm-none-eabi build.
Add 0x prefix for all values printed in hex.
Add LOG messages for error cases when enabling or disabling
paging.
Change-Id: I070c556e0ad31204231a2b572e7b93af22a9bc61
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2149
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b
Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is only the basic code proposed for mips32_pracc_exec() function.
It checks every pracc address against the expected address when
reading (instruction fetch).
The code expects to start at PRACC_TEXT and any subsequent read address
is obtained by adding 4 to the previous one.
After shifting out all the instructions the code executes a final check.
It checks now for the first pass trough PRACC_TEXT and shift out
only NOP instructions.
A mips core does not need an additional NOP and after the first check
it exits if there is no store access pending.
After shifting out one NOP the core must be reading at pracc text or the
code exits with error.
The code continues shifting out NOPs until all store accesses have
been performed.
After shifting out 10 NOPs it exits with error.
No assumption is made about the number of store instruction shifted out or
the ordering of the store accesses. It only checks that the number of
store accesses is the same as the number of store instructions at dmseg
after execution.
mips32_pracc_read_ctrl_addr() and mips32_pracc_finish() are added to
simpify a bit the code. Fields pa_ctrl and pa_addr are added
in ejtag_info for storing values of pracc control and address.
Change-Id: If6322d5c8cbeadcd4acd3972c0f72c8490f53c34
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1827
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is the first patch intended to make a more precise pracc check
when running in legacy mode (code executed by mips32_pracc_exec()).
It only makes some cleanups, mostly due to unnecessary code.
With the last cache optimizations for processor access (pa for short)
all the pracc functions generate the code following some rules that
make pa more easily to check:
There are no load instructions from dmseg. All the read pas are
instruction fetches. PARAM_IN related stuff is not needed.
Registers are restored either from COP0 DeSave or from ejtag
info fields. PRACC_STACK related stuff is not needed any more.
The code starts execution at PRACC_TEXT and there are no branch or jump
instruction in the code, apart from the last jump to PRACC_TEXT.
The fetch address is ever known.
For every store instruction to dmseg the function code sets
the address of the write/store pa.
The address of every store pa is known.
Current code ends execution when reading a second pass through PRACC_TEXT.
This approach has same inconveniences:
If the code starts in the delay slot of a jump it makes a jump
to PRACC_TEXT after executing the first instruction. A second pass
through PRACC_TEXt is read and the function exits without any warning.
This seems to occur sometimes when a 24kc core is halted in the delay
slot of a branch.
If a debug mode exception is triggered during the execution of a
function the core restarts execution at PRACC_TEXT. Again the function
exits without any warning.
If for whatever reason the core starts fetching at an unexpected
address the code now sends a jump instruction to PRACC_TEXT, but due
to the delay slot the core continues fetching at whatever address + 4
and a second jump instruction will be send for execution. The result
of a jump instruction in the delay slot of another jump is
UNPREDICTABLE. It may work as expected (ar7241), or let the core in
the delay slot of a jump to PRACC_TEXT for example. This means the
function called next may also fail (pic32mx).
Change-Id: I9516a5146ee9c8c694d741331edc7daec9bde4e3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1825
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Near all pracc functions store $15 in DeSave and
restore it when exiting.
There is no need to save it, if mips32_pracc_read_regs()
save this register in Desave when entering debug mode.
mips32_pracc_write_regs() needs to update it when
exiting debug mode.
Other pracc functions must not modify DeSave.
The jump code in the fastdata transfer function needs also
some little modifications.
Remark:
Like in current code the user can read/modify $15
with the cp0 31 commands.
Change-Id: I5b7dfc1b6169da846f5d2dd3ad4209a9da2c3fad
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1565
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently the code is loaded calling mips32_pracc_write_mem_generic().
Cache synchronization is not performed.
If configured as write back cache there is no chance to execute the
handler. If configured as write through cache and the cache
lines written to are not cache resident (I-side cache miss) may work.
The patch makes possible to execute the handler in a cached active
memory segment (mainly from KSEG0), but nothing else. The data
is still loaded without performing cache synchronization, code loaded
may not be executable.
Performance may not be faster. At start, for example, the code resides in
main memory, not in cache, and the core must transfer code from
memory. We can really modify the code to force a wait for the first
transfer like we do with start and end addresses, making sure the code
is cache resident for the rest of the queued transfers.
This can also may happen if we execute code (greater than the I cache size)
and the handler code is evicted from the cache.
Code tested on ar7241.
Change-Id: Iffdb4dae108b872fef0e7bacc5ea99649cdc1630
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1564
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently the functions mips32_checksum_memory() and mips32_blank_check_memory()
load the code word by word.
The bug in cache code is a good reason for doing so.
If there is no other reason we can load the code as a buffer to save time.
mips_m4k_write_memory() expect a buffer in target endianness, this is done by
target_buffer_set_u32_array().
Cleaned up exit code.
Tested on ar7241 big endian and pic32mx little endian with verify_image.
Flash erase check only tested in pic32mx.
Change-Id: Ib63ed98732b2e23b058e7349a0a57934b7604905
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1562
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Follows the the same rules of optimization used by all pracc functions.
Solves some bugs in previous code and adds support for write through caches.
Change-Id: If88c6738ca8c8197f327f22b766120a24f71b567
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1557
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
As exposed by arm-none-eabi build, fix the wrong modifiers.
Change-Id: Ia6ce7c5c1d40e95059525c3e5d81b752df2fea7c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2122
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paging checking and disabling wasn't present for IO r/w,
so the commands were successful only when paging wasn't
enabled (e.g. EFI boot phase).
Change-Id: I41366c0fadff3ea1eb8a153291f20a46cd9ddec1
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2118
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Since c6216201b2 gdb target description
generation support is enabled by default and it counts on checking
"feature" pointer in reg_list. Both mips32 and dsp563xx neither used
calloc nor explicitly set feature (as it was a newly introduced struct
field).
This patch changes all targets to use calloc for consistency.
Change-Id: I9eceadef8b04aacb108e24ae23cb51ca3009586f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2102
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to the "Arm Arch Ref Manual ARMv7-a and ARMv7-R edition" the
CPSR encoding for Monitor mode is 0b10110 (22) not 0b11010 (26) as is
currently used.
Change-Id: I73373a0029a81abc92febf518b88bf0dd4dec1fa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2081
Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Tested-by: jenkins
Reviewed-by: Younes REGAIEG <y.regaieg@gmail.com>
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If gdb was disconnected by the moment the target entered halted state,
update_halt_gdb would segfault.
Change-Id: I67477e9199c1df097be83a49e38602f975c083f5
Reported-by: Younes REGAIEG <younes.regaieg@imag.fr>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
COMMAND_PARSE_NUMBER may return, thus any memory allocated may not be
freed, simple reorder fixes the issue.
Change-Id: I0ce444a5b032f5c49b6d33a03a8c0b71cad49c8c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2065
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GPL requires providing sources for any derived work. I do not see any
reason to not include the xscale stuff into release tarballs.
Wildcard matching is used because plain directory name matches
implicit rule for executables and xscale.c built is errorneously
attempted, and directory name with a slash duplicates a directory
(xscale/xscale) in dist.
Change-Id: Ie0266470dcb97be87a09ba2dda9b3957f7cbc2fa
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1911
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Ignoring the value parameter in that function makes its code rather
misleading. Also the only caller of it, armv7m_restore_context already
does the whole "buf_get_u32" conversion business, so using
'value' also removes the waste of doing the conversion twice.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I515979c314d9b59ee1065c55b5bb5747c7e93f01
Reviewed-on: http://openocd.zylin.com/2057
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The timer callback is started on target init, but it makes no sense to
poll until the target is fully setup.
Change-Id: I118201e125e39be3d0a920e3ef9a3f68a2035f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2041
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ST-LINK/V2 has limited internal buffering, such that trace data
can be missed if the target is generating data at a rate quicker than
the OpenOCD trace sampling. The issue of lost data is compounded since
individual TPIU packets may be split across individual STLINK_TRACE_EP
reads, and misleading results can occur if mid-packet loss occurs.
This patch increases the frequency of checking for pending trace data
with the aim of minimising such losses. Note: With the limited (I/O
and memory) bandwidth of the ST-LINK/V2 there cannot, however, be a
guarantee against trace data loss.
The timer callback is only added when enabling tracing, and is removed
when tracing is disabled.
Change-Id: Ibde9794b77793d3068f88cb5c1a26f9ceadcbd8a
Signed-off-by: James G. Smith <jsmith@ecoscentric.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1661
Tested-by: jenkins
Make the APB-AB memory read routines handle endianess order
when running on big endian host. cortex_a8_read_apb_ab_memory
is also called by cortex_a8_write_apb_ab_memory and was breaking
both APB-AB read and write functions. Also fixed bug in write
function in calculating the offset of end of buffer data. The
change aslo fixes the read issues with all combinations of
aligned unaligned memory access found by 'test_mem_access' cmd.
Tested with target "test_mem_access 4000", also size 1-9,
'mdb/h/w' 'mwb/h/w' cmds and equivalent gdb 'x' 'set' cmds.
Change-Id: Ia927c60c4837617f5342a9beb6fdab1f061855fe
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1781
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
This makes the listing easier to read, imho. The tab indentation
technique causes the base address to precess as the parser proceeds
through the subtables, and can easily wrap.
Change-Id: Iea5e678255e6314a9d532e4b222a2572b5394390
Signed-off-by: Brad Riensche <brad.riensche@gmail.com>
Reviewed-on: http://openocd.zylin.com/1518
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Move the ROM table printing into a separate function to allow
recursive calls with nested tables. ROM tables can nest. The
printing is limited to 16 levels.
Update the types of tables printed. When an entry can't be read, print
a warning and continue.
Change-Id: Ib134edd9e987af2f5f606071521885b17af4d70f
Signed-off-by: Chris Johns <chrisj@rtems.org>
Reviewed-on: http://openocd.zylin.com/1427
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
v2:
- Split work into separate patches
The received packet will not be altered in any of the processing functions.
Some it can be made "const".
Change-Id: I7bb410224cf6daa74a6c494624176ccb9ae638ac
Signed-off-by: Christian Eggers <ceggers@gmx.de>
Reviewed-on: http://openocd.zylin.com/1919
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Perform proper ICache flush operations on memory writes. This should fix
inability to use software breakpoints for debugging with caches
enabled.
This patch is only compile-time tested.
Commit 1137eaedaf fixed the same issue
for arm920t. Among all the arm7_9_common targets only arm926ejs seems
to be broken in the same way.
Change-Id: I575306ac4319a69fc637b42f7c958f4595c5e81f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1912
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Intel Quark X10xx SoC debug support added
Lakemont version 1 (LMT1) is the x86 core in Quark X10xx SoC
Generic x86 32-bit code is in x86_32_common.c/h
Change-Id: If2bf77275cd0277a82558cd9895b4c66155cf368
Signed-off-by: adrian.burns@intel.com
Reviewed-on: http://openocd.zylin.com/1829
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
On a target where AHB AP memory access is unavailable, care should be
taken to avoid treating addresses as virtual if the MMU was disabled
at the time the target was stopped.
Without this it's impossible to peek memory with Gdb when debugging
e.g. a bootloader because cortex_a8_read_memory() unconditionally
tried (and failed because of a sanity check in cortex_a8_mmu_modify)
to enable MMU.
Change-Id: Id7c63f4912920fb71a6104226ec6428d18c96a56
Reported-by: mbm@openwrt.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1787
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the standard every operation returns at least an integer,
so PRIu8 format specifier is not suitable for these values as is.
This breaks build on OS X (x86_64-apple-darwin13.0.0) with "Apple LLVM
version 5.0 (clang-500.2.79) (based on LLVM 3.3svn)".
Fix by adding appropriate casts. In fact there's plenty of room (and
I'd say necessity) for factoring out common code in there, but it's
too invasive for a non-maintainer.
Change-Id: I7d2182eb1d2f86fa22c882fbbaa6cfadf1c3e8fc
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1878
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The argument 'force' enables a user to bypass the internal cache and read
a target register directly. However it is missing from the user guide.
Change-Id: I26f689eec20b38a0dc5294626b25df566b554446
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1897
Tested-by: jenkins
Commit ff5ec942d8 made this target
always use generic arm7_9 memory write routines for software
breakpoints which resulted in inability to debug and single-step
sources in Gdb when icache is active as generic routine doesn't
invalidate it. This should fix it (and is real-life tested against
Samsung S3C2442). I expect other arm7-9 targets to be affected as
well.
Change-Id: Id7980e370ae4db47ac6b1490321d81ffe85711c0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1817
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This commit adds support for passing the ARM4 target description to GDB
when enabling gdb_target_description, in order to expose all banked
registers.
Change-Id: Id618bc6226f00fe83397ea28888a84b64b09cafd
Signed-off-by: Luca BRUNO <lucab@debian.org>
Reviewed-on: http://openocd.zylin.com/1810
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The out only version of jtag_add_dr_scan smells like a bogus optimization
that complicates the minidriver API for questionable gain.
The function was only used by four old ARM targets. Rewrite the callers
to use the generic function and remove all implementations.
Change-Id: I13b643687ee8ed6bc9b6336e7096c34f40ea96af
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1801
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Review and modify to conform to C99 integer types format specifiers.
Use arm-none-eabi toolchain to build successfully.
Change-Id: If855072a8f88886809309155ac6d031dcfcbc4b2
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Signed-off-by: Hsiangkai <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is used for the emulated DCC channel which is only maintained as long
as target->dbg_msg_enabled is set. Skip the saving and restoring if not
enabled to save one dap_run() per core register access.
Note that we could've probably queued all core register accesses in the
same transaction if the armv7 register framework hadn't required
synchronous register accesses.
Change-Id: I4fe6d713261ee5db42422203eb63035fdcc48891
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1848
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It's far nicer to pass a size parameter than to split the calls to
separate wrappers which are combined to a single function anyway.
Change-Id: I716741ebf916f6f8e9358a31c8f4fe761107c82f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1847
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
This is not in the Intel hex file format specification but
some hex files may include comments (i.e. Altera USB-Blaster II
firmware) starting with '#'.
This patch makes image_ihex_buffer_complete_inner to skip
comment lines.
Change-Id: Id1f57d84d75da45e592f1c72b2b8c29193bc14e3
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1842
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the flash is not ready (MDM_STAT_FREADY is 0) then
dap_syssec_kinetis_mdmap() would act as if the MDM_STAT_SYSSEC bit was
set and erase the flash. Wait until MDM_STAT_FREADY is set before
checking the MDM_STAT_SYSSEC bit.
Change-Id: I5c3352f625599016625ed9be8787033f49bfacea
Signed-off-by: Per Ekman <pekenator@gmail.com>
Reviewed-on: http://openocd.zylin.com/1762
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Peter Lawrence
Spencer Oliver
Paul Fertser
Jon Burgess
Andreas Fritiofson
Angus Gratton
Oleksij Rempel
Kamal Dasu
Mathias K
Andrey Smirnov
Fatih Aşıcı
Jiri Kastner
Franck Jullien
Seth LaForge
Alex Ray
Ivan De Cesaris
Salvador Arroyo
Tim Sander
Brad Riensche
Chris Johns
Christian Eggers
Antony Pavlov
Adrian Burns
Luca BRUNO
Hsiangkai Wang
Per Ekman
Sergio Chico
Dongxue Zhang