Add access to dsp registers and a command for dsp related operations.
Checkpatch-ignore: MACRO_ARG_REUSE
Change-Id: I30aec0b9e4984896965edb1663f74216ad41101e
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7867
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command substantially complicates support of nRF53/91
series. It was not even properly ported to nRF52.
The informative value is disputable. Who wants to see
e.g. override trim values for radio or unique device ID?
Drop it and simplify the driver.
Change-Id: Ia7fb20ce2ebf16065705c5d18deaf934e58db426
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Prior to the change when calling `log_output` without any arguments it
was unclear where the log was redirected.
Change-Id: Iaa3ecea8166f9c7ec8aad7adf5bd412799f719a1
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8071
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enable support for USB vid and pid combinations other than 0x0403/0x6001
on OpenJTAG adapters.
Change-Id: Ibb5fb14a6f33abbc011dbf3179df20d79ed74a7a
Signed-off-by: N S <nlshipp@yahoo.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8100
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add detection for mips cpu types by using prid.
Add cpuinfo command for inspecting more verbose info.
Add MIPS Architecture specs in openocd docs.
Change-Id: I28573b7c51783628db986bad0e226dcc399b4fa6
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7912
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested with APM32F030C8T.
Change-Id: I63cd8b66424135dae481a96ba560e6f0b1f9544e
Suggested-by: Christian U <info@cu-tec.de>
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8014
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some devices with an internal multi-tap JTAG router require a vendor
specific bypass instruction to bypass the master TAP when addressing
slave taps internal to the same device. On these devices the standard
bypass instruction bypasses the whole device.
Change-Id: I4506f0e67c9e4dfe39b7fa18c63d67900313e594
Signed-off-by: Henrik Nordström <henrik.nordstrom@addiva.se>
Reviewed-on: https://review.openocd.org/c/openocd/+/8041
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If the remote_bitbang host does not execute requests immediately,
delays performed inside OpenOCD can be lost. This option allows
the delays to be sent to the remote host so that they can be
queued and executed in order.
Signed-off-by: Jeremy Herbert <jeremy.006@gmail.com>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Change-Id: Ie1b09e09ea132dd528139618e4305154819cbc9e
Reviewed-on: https://review.openocd.org/c/openocd/+/7472
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce 'cmsis-dap quirk' command to enable and
disable quirk mode.
If enabled, disconnect and connect before a switch
sequence and do not use multiple packets pipelining.
Change-Id: I6576f7de9f6c98a25c3cf9eec9a456a23610d00d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7966
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix the 'wp' command documentation.
Change-Id: I70f3110e8ce286051f8f810260f1857b2285e634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8022
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This is useful when using the SEGGER RTT tooling, as the SEGGER RTT
tool J-Link RTT Viewer version 7.84f requires that it receives a
messages immediately after connecting. Otherwise it will give a timeout
and it will not connect.
Change-Id: I9240a1b6a93cd5c0fbd18292afb33b89013d78bf
Signed-off-by: Thiemo van Engelen <tvanengelen@victronenergy.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7752
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This allows programmatically determining the debug reason.
Change-Id: I0c3e85cebb6dc28fc0fc212beca84a484ac654a5
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7952
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This patch adds the "all" option to the rwp command.
It removes all watchpoints, much like rbp all removes
all breakpoints.
Change-Id: Id58dd103085e558f17afa4a287888cf085566ca9
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7907
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously, if you ran a tcl command in capture like so:
"capture { reg 0x1000 hw }"
Such command did overwrite the tcl result if LOG_LVL_INFO or
lower was logged during it.
This patch changes it by prepending the log to the tcl result instead.
As the tcl results should not be lost during capture.
Change-Id: I37381b45e15c931ba2844d65c9d38f6ed2f6e4fd
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7902
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
add refresh command for lattice devices
rename gowin reprogram to refresh
rename virtex2 program to refresh
Change-Id: I9da83a614b96da3e947ac4608b0a291b1d126914
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7839
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Jtagspi is using a proxy bitstream to "connect" JTAG to the
SPI pins. This is not possible with all FPGA vendors/families.
In this cases a dedicated procedure is needed to establish such
a connection.
This patch adds a jtagspi-mode for these cases. It also adds the
needed interfaces to jtagspi and the pld-driver so the driver
can select the mode and provide the necessary procedures.
For the cases where a proxy bitstream is needed, the pld driver
will select the mode and provide instruction code needed in this
case.
Change-Id: I9563f26739589157b39a3664a73d91152cd13f77
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7822
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added NPCX flash driver to support the Nuvoton NPCX4/K3 series
microcontrollers. Add config file for these series.
Change-Id: I0b6e128fa51146b561f422e23a98260594b1f138
Signed-off-by: Luca Hung <YCHUNG0@nuvoton.com>
Signed-off-by: Mulin CHao <mlchao@nuvoton.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7794
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This emulation mode supports software translation of an AP request
into an address mapped transaction that does not rely on physical AP
hardware. This is necessary in some hardware such as K3 SoCs since the
hardware architecture anticipates a potential race condition between
AP doing direct memory access generating transactions back to system
bus and firewalls that data path out.
This emulation mode allows direct memory driver to emulate CoreSight
Access Port (AP) and reuse the SoC configuration meant for JTAG
debuggers.
Since the address ranges are flat in nature, the requisite memory base
and size will need to be provided a-priori to the driver for mapping.
The other design alternative would be to map requested memory map for
every register operation, but, that would defeat our intent of getting
max debug performance.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I2d3c5f7833f1973e90b4f6b247827f62fc2905d0
Reviewed-on: https://review.openocd.org/c/openocd/+/7089
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Direct memory driver support for CoreSight Access Port(AP).
Even though we emulate SWD (serial wire debug), we aren't actually
using swd. Instead, we are using a direct memory access to get to the
register set. This is similar in approach to other fast access native
drivers such as am335xgpio drivers.
Example operation on Texas Instrument's AM62x K3 SoC:
+-----------+
| OpenOCD | SoC mem map
| on |--------------+
| Cortex-A53| |
+-----------+ |
|
+-----------+ +-----v-----+
|Cortex-M4F |<───────| |
+-----------+ | |
| DebugSS |
+-----------+ | |
|Cortex-M4F |<───────| |
+-----------+ +-----------+
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I8470cb15348863dd844b2c0e3f63a9063cb032c6
Reviewed-on: https://review.openocd.org/c/openocd/+/7088
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The bcm2835gpio driver preferred /dev/gpiomem for access to
memory mapped GPIO control and used /dev/mem as a fallback
only if it couldn't open /dev/gpiomem.
/dev/mem usually requires elevated rights or specific capabilities
of the opening process, so the fallback failed anyway.
Although /dev/gpiomem is the strongly preferred option with respect
to security, there could be also use cases which require /dev/mem
even if /dev/gpiomem is available (e.g. changing the GPIO pad
settings is necessary or testing/debugging OpenOCD).
It was difficult to handle such cases because they required
to block globally the system device /dev/gpiomem
(remove, rename or chmod).
Drop the fallback feature and select the memory device
by 'bcm2835gpio peripheral_mem_dev' configuration command.
Use /dev/gpiomem as a default.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I60e427bda795d7a13d55d61443590dd31d694832
Reviewed-on: https://review.openocd.org/c/openocd/+/7350
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The pads were configured at a wrong memory address
if /dev/gpiomem was mapped.
The pad setting registers are not accessible in mapped /dev/gpiomem,
disable the pads setting if the driver doesn't open /dev/mem.
While on it, do not fail the driver initialization if pad mapping fails
- just emit a warning and work with unchanged pad setting.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I0bce76cade8f7efd75efd9087a7d9ba6511a6239
Reviewed-on: https://review.openocd.org/c/openocd/+/7684
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Walter Ji
Tomas Vanek
Evgeniy Naydanov
N S
ianst
David Vidrie Leon
Marc Schink
Henrik Nordström
Jeremy Herbert
Karl Palsson
Manuel Wick
Thiemo van Engelen
Peter Collingbourne
Marek Vrbka
Daniel Anselmi
Luca Hung
Jason Peck
Nishanth Menon
Ahmed BOUDJELIDA
Parshintsev Anatoly
Laurent LEMELE
iosabi
Erhan Kurubas