Starting the daemon with with just a bare "openocd" I saw:
Can't find openocd.cfg
That's not an error; don't treat it as if it were. There may
be an error later -- like, "no interface set up" -- but let
messages only report real errors, not fake ones.
JTAG has only two possible JTAG ack codes for APACC and DPACC
register reads/writes. Define them, and remove empty "else"
clause in the code which now uses those codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I think some of these assumptions are not well-founded.
Related, that swjdp_transaction_endcheck() is a bit iffy.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The gdb_port command can be invoked during normal execution
to report the port used for gdb, whereas it was listed as
CONFIG stage only, which caused an error when excuting
it to return the reported error.
Also in line with the grander goal of making more commands
available during all "modes" (perhaps retiring config mode),
there is no particular reason to limit gdb_port to the
config stage.
Regression was introduced in:
b3bf1d12b2 aka
v0.4.0-rc1-32-gb3bf1d1
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add doxyegen description for this driver.
Correct the helptext (configures *or* displays based on #params),
and usage (use the same BNF as the User's Guide).
Remove superfluous #include
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove superfluous #include.
Correct the helptext (configures *or* displays based on #params),
and usage (use the same BNF as the User's Guide).
Add doxygen -- file-level description and a @todo for doing
RTCK correctly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The command processing conversion a while back lost the
"rtck" enable/disable command; restore it.
NOTE that having such a command is wrong; there's a standard
way to enable adaptive clocking ("speed 0").
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Build fixes: it failed abysmally with PPDEV enabled. Swapped
a build-time error with a FIXME comment in the affected macros.
Cleanup: remove "&" before function pointers, and excess indent,
for the interface struct declaration.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename DAP_IR_* as JTAG_DP_* since those symbols are specifically
for JTAG-DP (or SWJ-DP in JTAG mode), and won't work with SWD.
Define the JTAG ABORT and IDCODE instructions for completeness;
add a comment about where to (someday) use ABORT.
Fix messaging which assumes everything is an SWJ-DP; say "JTAG-DP"
instead, it's at least more appropriate for all JTAG transports.
Shrink the affected lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix: don't print the BASE address except if it's a MEM-AP;
that's an unlikely error, but there's no point getting it wrong.
Tweaks: comments, capitalization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make some private functions "static". Remove their public declarations,
and what is now an obviously unused function. Shrinks this object's size
(about 5% on x86_64) while making the code's scope easier to understand.
Shrink the affected lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Instead of magic numbers, use their AP_REG_* constants. Rename
the ROM address symbol as BASE to match ARM's documentation.
Comment various other symbols in the header; add some missing ones.
Remove an unused struct. Add some doxygen for stuff including the
DAP structure and initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Shrink some lines, add some comments, simplify some tests.
During debug startup, log the core revision level too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This makes it so that the usage/help command properly uses the whole command,
including subcommand, in the search for help information. This previously
caused erroneous output from the usage command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I wanted to make it so I can be ignorant of a commands invocation string, so
I tried to use CMD_CURRENT (aka cmd->current) which is supposed to house a
pointer to the current command. It turns out that this wasn't being set.
This patch adds the current command structure to the command invocation
structure before sending it along to the command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Handlers for commands
- arm7_9 semihosting <enable | disable>
- $_TARGETNAME arp_reset assert 1
didn't check if target has already been examined, and could
segfault when using the NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove useless space/tab at end of lines.
Remove spaces in indentation and replace with tab.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The handler for "arm9tdmi vector_catch ..." did not check
if target has already been examined. Without this fix it
segfaults when using NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Misc:
- Introduce some "struct reg" temporaries, for clarity
- Shorten lines
- Add some missing whitespace
- Clean up comments
- Add notes about some fault handling issues
- Most of these errata workarounds are for *OLD* chip revisions
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
And add my copyright. MPCore is untested, but it's the
only other ARM11 core to care about.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Command "reset halt" checks if PC properly resets, issueing warning:
"PC was not 0. Does this target need srst_pulls_trst?".
Checking PC against 0 is not always correct.
Removed PC value check, as suggested by Øyvind Harboe.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: U-PROPRIET-28D9DF\PROPRIETAIRE <PROPRIETAIRE@propriet-28d9df.(none)>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
In conjunction with manual register setup, this lets the ETM trigger
cause entry to debug state. It should make it easier to test and
bugfix the ETM code, by enabling non-trace usage and isolating bugs
specific to thef ETM support. (One current issue being that trace
data collection using the ETB doesn't yet behave.)
For example, many ARM9 cores with an ETM should be able to implement
four more (simple) breakpoints and two more (simple) watchpoints than
the EmbeddedICE supports. Or, they should be able to support complex
breakpoints, incorporating ETM sequencer, counters, and/or subroutine
entry/exit criteria int criteria used to trigger debug entry.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Change handling of the CYCLE_ACCURATE, BRANCH_OUTPUT, and
TRACE_* flags; also the CONTEXTID size values.
- Convert to symbols matching the actual register bits, instead of
some random *other* bits (and then correcting that abuse).
- Get rid of a now-needless enum.
- Keep those values in etm->control, and remove etm->tracemode.
These values all affect the trace data that's recorded by a trace
pod or in the ETB. I modified the file format used to dump ETB
data; since it's fairly clear nobody can use this mechanism now,
this can't cause anyone trouble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide better comments for the ETM_CTRL bits; use the correct bit
for half/full clock mode; and define a few more of the bits available
from the earliest ETM versions.
The new bit defintions use ETM_CTRL_* names to match their register
(instead of ETM_PORT_* or ETMV1_*). For clarity, and better matching
to docs, they are defined with bitshifting not pre-computed masks.
Stop abusing typdefs for ETM_CTRL values; such values are not limited
to the enumerated set of individual bit values.
Rename etm->portmode to etm->control ... and start morphing it into a
single generic shadow of ETM_CTRL. Eventually etm->tracemode should
vanish, so we can just write etm->control to ETM_CTRL.
Restore an "if" that somehow got dropped.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This command was misplaced; it's not generic to all traceport drivers,
only the ETB supports this kind of configuration. So move it, and
update the relevant documentation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Much to my surprise, I observed a "flash erase_address ..."
command erasing data which I said should not be erased.
The issue turns out to be generic NOR flash code which was
silently, and rather dangerously, morphing partial-sector
references into unrequested whole-sector ones.
This patch removes that low-level morphing. If desired, it
can and should be done in higher level code. (We might need
to fix some stuff in the GDB server code.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's currently allocating a big buffer but writing it out in
units of sizeof(host's pointer) ... sub-optimal.
Plus fix a couple minor coding style goofs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Word count == size/4; cope. And increase buf_min so it's large
enough to cover the overhead in my tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We can actually do the right thing if the MMU is off; save
the error message for the phys-but-MMU-enabled path, which
is what isn't yet supported.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Try to right-size the SRAM buffers, by not:
- using them for very small writes
- giving up when a large buffer isn't available
- allocating buffers much larger than their data
Also don't:
- bother loading the code unless we allocate the writebuffer too
- be so verbose with messaging:
* be more concise
* reduce importance (e.g. DEBUG not WARNING)
* remove duplication
The minimum buffer size is something of a guess. It's eight
times smaller than before, almost the same size as the code
being downloaded. It probably deserves some tuning.
Also, note an erratum affecting flash protection on some chips;
and narrow many over-wide lines affected by the above changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Refactored the write page raw function into two new functions
for writing data to a NAND device and then another function to
finish up a write to a NAND device. This includes some new
updates to introduce more error checking to existing code.
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Added a new function to encapsulate reading a page of data from
a NAND device using either the read_block_data function of a NAND
controller or to use direct reading of data from the NAND device.
This also adds some performance enhancements and uses the read_data
function if the read_block_data function fails safely (because it
can't allocate a buffer in the working area).
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tweak the "scan_chain" output by removing column separators. Also
remove the "current instruction" state ... which changes constantly.
Now its style resembles the "targets" output, and can even fit on
one line in standard terminals and in the PDF docs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Someday revisit various issues: Tempest parts support writing
more than one word at a time; for some target firmware it might
be necessary to save and restore flash IRQ configuration. (The
safest policy is likely to always reset after flash updates.)
Plus swap some undesirable TAB characters with SPACE.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix potential memory leak: make sure the per-bank data
structures are only allocated in probe(), and that calling
probe() multiple times is a NOP. Use it for auto_probe().
Require probe() to have done its thing: don't make access
routines cope with it not having been called. Shrink a
bunch of failure paths; and in some cases, correct them.
Don't needlessly insist on a halted target for probe().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No point in reading and discarding a status value when fetching
part description data. Or having that needless "#if 0" code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously "reading" clock info (and part info) also, as a side
effect, wrote the flash timing register. Instead, be more safe:
"reading" should only read. Write paths still refresh timing,
coping with changes the application code may have made.
Also rename the routine which sets flash timing, indicating what
it's really doing; it's got nothing to do with a "mode".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
By exhausting data on input, the performance will be more
consistent + the code more clearly distinguishes between
polling and processing. A test showed gdb packet load
performance go from ~1550kByte/s to 1650kBytes/s + being
more stable.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Teach ARM11 how to use:
- the new "reset-assert" event
- vector catch to implement "reset halt"
- use SRST more like other cores do
- ... including leaving post-SRST delays up to config scripts
This gives OMAP2420 the ability to reset, and doesn't seem to
cause new iMX31 problems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I added the remaining devices and device IDs to stellaris.c, and
removed several devices that don't exist on the Stellaris web page.
Additionally, I found a few devices with duplicate IDs ... the DID1
Version Number for LM3Sxxx parts have DID1 Version = 0x0, and for
LM3Sxxxx have DID1 Version = 0x1. So I extended the comparison to
use the VER and FAM fields from DID1 also.
ID=0x33: LM3S812 (DID1v0) and LM3S2616 (DID1v1)
ID=0x39: LM3S808 (DID1v0) and LM3S2276 (DID1v1)
These are the parts I removed from the file for lack of documentation
(no data sheet to confirm part ID):
LM3S318,
LM3S1101, LM3S1108,
LM3S1615, LM3S1616,
LM3S2016,
LM3S2101, LM3S2108,
LM3S3759, LM3S3768,
LM3S5757, LM3S5767, LM3S5768, LM3S5769,
LM3S6815, LM3S6816,
LM3S6915, LM3S6916,
LM3S6111, LM3S6118.
Also, sort devices according to part number.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a "-ignore-version" to "jtag newtap" which makes the IDCODE
comparison logic optionally ignore version differences.
Update the "scan_chain" command to illustrate this by showing
the "*" character instead of the (ignored) version nibble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make these ".h" files adopt the same policy the ".c" files already
follow: don't use <subsystem/...h> syntax for private interfaces.
If we ever get reviewed/supported "public" interfaces they should
come exclusively from some include/... directory; that'll be the
time to switch to <...> syntax for any subsystem's own interfaces.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't include <helper/jim.h> from target.h ... not everything
which touches targets needs to be able to talk to Jim. Plus,
most files include this header by another path.
Also, switch the affected files to use the classic sequence
for #included files: all <framework/headers.h> first, then
the "local_headers.h". This helps prevent growth of problematic
layering, by minimizing entanglement.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For some routines that only returned ERROR_OK and where the
caller never checked ... don't bother. Remove some noise,
and bugfix some comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Abstract the DPM breakpoint and watchpoint data structures to
have a shared core for housekeeping.
Abstract the code updating the watchpoint registers so that it
can be used to update breakpoint registers. Then do so, when
something has set up the breakpoint state used by this code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Properly detect all of these, including the "2" variants;
and bugfix parameter display for LDC and STC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
ITR register handling seemed to be giving me problems, so I updated
the comments to better say what the code is trying to do ... and to
note the preconditions (one of which seems to be an issue) as listed
in the ARM1136 TRM.
Also removed the unused "ARM11_TAP_DEFAULT" from the ITR scan code;
all the callers already specify an exit path, since this register
isn't usable with such vague semantics.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This fixes the issue under native win32 of the socket interface not being
enabled (via WSAStartup) before init is called from a script.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
I neglected to copy Magnus' copyright when I moved several
declarations from the ARMv7-M header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Bugfix the read side of flash protection:
- read the right register(s)!
- handle more than 64K
- record the results in the right places
- don't display garbage.
Partially bugfix the write side:
- use 2KB lock regions instead of 1KB pages (!)
- validate input range
- don't try to _remove_ protection (it's write-once)
- #define values we'll need to commit writes.
- ... still doesn't handle pages over 64KB mark, or commit writes
And minor cleanup and fixes:
- get rid of some forward decls
- properly locate a doxygen comment
- fix some bad indentation
- remove superfluous #include
- add a new part ID (many are still missing)
- make the downloaded algorithm code be read-only
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
These were all basically "can't happen" cases ... like having
state be corrupted by an alpha particle after the previous check
for whether a value was in-range.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of these happened to be in the target.h file.
Some of those are associated with symbols that could be
removed at some point ... e.g. NVP_ASSERT/true and its
sibling NVP_DEASSERT/false.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The exception being declarations for drivers. Those should
be split out in some clean way -- like driver add/remove calls
made by initialization code -- but that's for another day.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's as if despite integers being 32-bits, GCC refuses to
convert a "uint32_t" to one of them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Low latency low CPU processing power systems(embedded)
will benefit greatly from being able to inline certain
jtag_add_xxx() fn's. The trick is that this has to be
done in such a way as to allow implementing an OpenOCD
API with a shared library(eventually) on a PC hosted
OpenOCD.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Some versions of GCC don't understand that if you mask with 0x3
then have cases 0-3, it's not possible for a variable assigned in
all those branches to have no value at end-of-case. Feh.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
When starting up, say how many hardware breakpoints and watchpoints
are available on various targets.
This makes it easier to tell GDB how many of those resources exist.
Its remote protocol currently has no way to ask OpenOCD for that
information, so it must configured by hand (or not at all).
Update the docs to mention this; remove obsolete "don't do this" info.
Presentation of GDB setup information is still a mess, but at least
it calls out the three components that need setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide and use debug_reason_name() instead of expecting targets
to call Jim_Nvp_value2name_simple(). Less dependency on Jim, and
the code becomes more clear too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Have various ARM cores delegate to arm_arch_state() to display
basic information, instead of duplicating that logic.
This shrinks the code, makes them all report when semihosting
is active, and highlights which data are specific to this core.
(Like ARM720 not having separate instruction and data caches.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move most declarations in <target/armv4_5.h> to <target/arm.h>
and update users.
What's left in the older file is stuff that I think should be
removed ... the old register cache access stuff, which makes it
awkward to support microcontroller profile (Cortex-M) cores.
The armv4_5_run_algorithm() declaration was moved too, even
though it's not yet as generic as it probably ought to be.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename some (mostly) generic ARM functions:
armv4_5_arch_state() --> arm_arch_state()
armv4_5_get_gdb_reg_list() --> arm_get_gdb_reg_list()
armv4_5_init_arch_info() --> arm_init_arch_info()
Cores using the microcontroller profile may want a different
arch_state() routine though.
(Also fix strange indentation in arm_arch_state: use tabs only!
And update a call to it, removing assignment-in-conditional.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the ARM opcode macros from <target/armv4_5.h>, and a few
Thumb2 ones from <target/armv7m.h>, to more appropriate homes
in a new <target/arm_opcodes.h> file.
Removed duplicate opcodes from that v7m/Thumb2 set. Protected
a few macro argument references by adding missing parentheses.
Tightening up some of the line lengths turned up a curious artifact:
the macros for the Thumb opcodes are all 32 bits wide, not 16 bits.
There's currently no explanation for why it's done that way...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Get rid of mrc_opcode() in favor of ARMV4_5_MRC() or, where
arm*20t should have used it, ARMV4_5_MCR() instead.
Basically, *writing* coprocessor registers shouldn't have
used the *read* opcode ... and both should stick to standard
opcode constructors, not rearranging parameter sequence any
more than already needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The SRS and RFE instructions speed exception entry/exit by
making it easy to save and restore PC and SPSR. This handles
both ARM and Thumb2 encodings.
Fix minor PLD goofage; that "should never reach this point"
can't happen, so remove it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The low two bits are defined as should-be-zero-or-presereved.
We'll take the zero option, it's easier to enforce.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the existing 'flash banks' implementation as 'flash list', and
replace the broken 'flash_banks' TCL wrapper with a new command handler.
Adds documentation for the new 'flash list' command in the user guide.
The 'flash banks' command produces a list that needs to be formatted
properly for GDB's 'mem info' to work properly. The flash_banks TCL
wrapper provided this formatting, but wrappers no longer work for
second-level commands as they did in the past. With this patch,
the 'flash_banks' command can be used with the new command syntax
and display the required information.
More updates from the code review by Steve Grubb <sgrubb@redhat.com>.
The Jim float-comparision bug just gets a comment not a fix, though.
Cc: Steve Grubb <sgrubb@redhat.com>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fall back to software breakpoint when vector catch isn't available.
Possible enhancements:
- add extra optional command parameter to select high vectors
- add extra optional command parameter to select hardware breakpoint
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename nand.h as flash/nand/core.h, chase consumers. The public APIs
need to be sorted out with imp.h, but this allows other changes to
begin improving the separation between policy and mechanism.
Moves #include <target/target.h> and #include "driver.h" into the
internal headers or source files, removing it from <flash/nand/core.h>.
Moves commands into nand/tcl.c and core implementation to 'nand/core.c'
and 'nand/fileio.c'. Eliminates 'flash/nand.c'.
Adds 'nand/imp.h' to share routines between TCL commands and core.
This work parallels the NOR directory, encapsulating the NAND drivers
into a separate file. This takes an extra step by encapsulating the
type of data structure used to manage the drivers, allowing it to be
changed from an array to a dynamic list in the future.
Remove an undesirable use of the CPSR symbol ... it needs to vanish.
Flag mode-to-number stuff as obsolete; say why ... should also vanish.
Get rid of no-longer-used mode and state typedefs.
Comment a few of the implicit ties to "classic ARM".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
As with Cortex-A8, the WFAR register holds useful information
that should be recorded and, where relevant, displayed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tweak scanchain 7 debug messaging:
- show register addresses in decimal, matching ARM docs;
- remove some pointless noise
Avoid some needless roundtrips:
- skip SCAN_N when SCREG already holds that number (speeds up
polling and other common operations)
- avoid zeroing vcr twice on resume
Show the IR opcode as a label ("RESTART") too; and in decimal,
matching ARM docs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the bulk of the flash.h file into flash/nor/core.h, leaving an
empty husk that will be removed in the next patch.
The NOR driver structure is an implementation detail, so move it into
its own private header file <flash/nor/driver.h> along with helper
declaration for finding them by name.
David Brownell
Spencer Oliver
David Claffey
Øyvind Harboe
Dean Glazeski
Antonio Borneo
Freddie Chopin
Piotr Esden-Tempski
Catalin Patulea
mkdorg@users.sourceforge.net
Eric Wetzel
Zachary T Welch
Rafael Campos Las Heras
Mathias Kuester
Nicolas Pitre