defining ntrst_delay is pointless; don't.
At least the LM3S3748 eval board doesn't need nsrst_delay
either; remove that too.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2645 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- remove endianness options; these chips hard-wire "little"
- $_TARGETNAME updates:
* don't pass $_TARGETNAME where a TAP label is required
* flash config uses $_TARGETNAME (it might not be target #0)
* simplify one $_TARGETNAME construction
- update work area setup:
* remove VM spec; these chips have no VM!
* fix some wrong sizes (0x4000 == 16K, not 4K)
* simplify: take defaults
- comment fixups
git-svn-id: svn://svn.berlios.de/openocd/trunk@2589 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add flash programming support for NXP LPC1700 cortex_m3 based family
git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
on ARM9 cores, and update the DaVinci config files so they
no longer explicitly specify it.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2484 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Prepare the DaVinci PLL code to support the version 0x0E module
used in newer chips (e.g. dm365): rename the original code so
it's specific to version 0x02 PLL modules, and update the dm355evm
code to use that new name.
Fix two minor bugs in that version 2 code: sysclk3 setup used
the sysclk2 divider address (affecting video processing on dm355,
no worry for now) and sysclk2 setup had a syntax error.
Also minor fixups to dm355evm, mostly to permit use of RTCK.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2447 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch adds support for the Luminary Micro LM3S9B90 target and
LM3S9B92 Evaluation Kit. These kits include a new ft2232 adapter, the
Luminary In-Circuit Debug Interface (ICDI) Board, so this is added as a
new ft2232 layout called "luminary_icdi".
git-svn-id: svn://svn.berlios.de/openocd/trunk@2429 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Minor bugfix ... previous version was tested *with* ICEpick active.
The "-disable" can swap with "-enable"; but not with an empty string.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2418 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Improve the PXA255 target config: move all that board-specific
setup to the pxa255_sst board.cfg, to which it evidently belongs
(it's the only PXA255 board now included).
Provide the PXA255 JTAG id from Intel docs, and add a comment
about how this chip is now EOL'd (last orders taken).
Note that I still can't get my old PXA255 board to work. There's
something broken in the reset sequence, which is preventing the
TAP from coming up at all. Old mailing list posts suggest this
is a longstanding bug...
git-svn-id: svn://svn.berlios.de/openocd/trunk@2416 b42882b7-edfa-0310-969c-e2dbd0fdcd60
source the STM32 target config instead of using a private clone
git-svn-id: svn://svn.berlios.de/openocd/trunk@2352 b42882b7-edfa-0310-969c-e2dbd0fdcd60
an improved DM355, integrating much better HD video support,
Ethernet, and other goodies.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2351 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update the Beagle setup:
- OMAP3530 updates:
* split ICEpick TAP enable support to its own file, for
reuse and eventually for storing other utility code
like emulation reset
* clean up, including labeling the tap as for DAP not
for the Cortex-A8 and making endianness non-variable
* add a few FIXMEs
- BeagleBoard cleanup: there's no SRST, "endstate" is gone, etc
I'm not sure I'd say it's further than "barely limping" just yet.
Key issues remain lack of Cortex-A8 support, and more complete
support for resetting.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2267 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Fix for a goofy "board" config ... reuse target/pxa270.cfg
instead of using a private copy.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2266 b42882b7-edfa-0310-969c-e2dbd0fdcd60
DM6446 config updates:
- List two more TAPs, as disabled, mostly for doc purposes
- Included basic ICEpick support, still disabled by default
- Shorten line lengths
- Use $_TARGETNAME to configure the ETM and ETB
- This ARM core don't support endianness overriding
For now, boards that can't jumper EMU0/EMU1 will need to tweak
a variable's setting.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2265 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add another board ... OMAP2420 "H4" board. This won't be very widely
used with OpenOCD, but with mainline support in both U-Boot and Linux
it at least makes for a more complete set (and another testcase).
This is incomplete support in several respects. The ARM11 support is
not very deep yet; most registers aren't available, and the ETM can't
be hooked up. Plus, there's no script for OMAP-specific stuff like
setting up the SDRAM controller. Eventually the same NAND controller
driver should work with OMAP2 and OMAP3.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2242 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Tweak the csb337 code so that it doesn't enable alignment traps when
it completes the "reset init" sequence. It turns out that the current
CFI code reliably triggers such traps.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2179 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add configuration for an old AT91rm9200 board, the Cogent CSB 337.
Worth noting from the OpenOCD perspective:
- It got a real hardware trace port connector; wired up here as
much as we can, lacking inexpensive trace-aware dongles.
- This is the first in-tree use of the "arm920t cp15" command.
It adjusts the CPU clocking and enables i-cache, which gives
more than 4x speedup after booting Linux; it's visible even
just running U-Boot.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2134 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This is the missing half of the r1974 patch:
OSK5912 board support, which was split out from
the omap5912 target config.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1985 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Split out OSK5912 board support from the omap5912 target config, and make
it pass sanity checks on my (Rev C/original) hardware:
- Fix syntax error ("-irlen" not "irlen")
- Provide real TAP ids for the ARM926ejs and the C55x dsp
- Label both CPUs appropriately (DSP, ARM)
- List both flash chips
The scan chain looks like this (note truncated DSP instruction code):
TapName | Enabled | IdCode Expected IrLen IrCap IrMask Instr
---|--------------------|---------|------------|------------|------|------|------|---------
0 | omap5912.dsp | Y | 0x03df1d81 | 0x03df1d81 | 0x26 | 0x00 | 0x00 | 0xffffffff
1 | omap5912.arm | Y | 0x0692602f | 0x0692602f | 0x04 | 0x01 | 0x00 | 0x0c
2 | omap5912.unknown | Y | 0x00000000 | 0x00000000 | 0x08 | 0x00 | 0x00 | 0xff
I still don't know what that third TAP is; maybe an early version of
an ICEpick JTAG router.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1974 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Move src/tcl to tcl/.
- Update top Makefile.am to use new path name.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1919 b42882b7-edfa-0310-969c-e2dbd0fdcd60
oharboe
duane
ntfreak
zwelch