Do not fail startup if communication with target is
not possible.
OpenOCD supports launching without a target connected
or the target powered down.
The user will typically power up the target and issue
a "reset init" + load his application after OpenOCD
is started then.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
This new cmd adds the ability to choose the Cortex-M3
reset method used.
It defaults to using SRST for reset if available otherwise
it falls back to using NVIC VECTRESET. This is known to work
on all cores.
Move any luminary specific reset handling to the stellaris cfg file.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
bitq.c: In function ‘bitq_scan_field’:
bitq.c:224: error: declaration of ‘pause’ shadows a global declaration
/usr/include/unistd.h:429: error: shadowed declaration is here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
committed so as to ease cooperation and to let it be improved
over time.
So far it supports:
- halt/resume
- registers inspection
- memory inspection/modification
I'm still getting up to speed with OpenOCD internals and AVR32 so code is a little
bit messy and I'd appreciate any feedback.
if a tap could not be _enabled_, the error message was
'failed to disable tap'. Fixed that. Also, display the failing
tap's name.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
The patch improves flash erase for STR9x in case of a full bank erase.
Then the chip erase command is used instead which improves speed significantly.
Also I think it might help if e.g. STR912 enters some state where flash banks are locked, and a chip erase command is the key for unlocking the flash.
ocd_ prefix is used internally in OpenOCD as a kludge more
or less to deal with the two kinds of commands that OpenOCD
has.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
if polling is off, then "reset run + halt" would fail
since halt incorrectly assumed the target was in the
reset state as it is the internal poll implementation
that moves the sw tracking of the target state out
of the reset state.
To reproduce:
> reset run; halt
JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1)
BUG: arm7/9 does not support halt during reset. This is handled in arm7_9_assert_reset()
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
back-off algorithm for polling. Double polling
interval up to 5000ms when it fails.
when polling succeeds, reset backoff.
This avoids flooding logs(as much) when working
with conditions where the target polling will fail.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It is useful to know that the printed errors are *all* the
errors there were.
Added missing error handling(found by inspection).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
it can be useful to throttle performance: test
differences in behavior, test performance effect
of long roundtrips.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This flash driver works on more than just two chips.
(Though it does need work still, e.g. to protect more than 64K.
(On non-'3748-A0 chips where errata allow that.))
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make it scriptable, so code can be conditionalized based on
what transport is in use for the session.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For the above targets the exit_point is
optional when used with run_algorithm, so remove it.
This makes updating the algorithm less error prone.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the mips32 uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the armv7m uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm4_5 codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Update the arm_checksum_memory and arm_blank_check_memory
algorithms to use a breakpoint instruction on v5 arch.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Set up more of the Luminary-specific signals, and stop cloning
a few of the JTAG defaults. More comments too.
Still leaves the "dap info 0" bugs unresolved (presumably coupled
to this particular adapter family) where TPIU, ITM, DWT, and other
debug modules wrongly display as extra NVICs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Provide $defines for more of the signals involved in the
Luminary ICDI hardware, and comment some of what's going on.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use addition for offsetting, not masking. Shorten some lines.
Make "component_start" print-only (unused otherwise; don't save).
Still doesn't resolve the issue where multiple components
are wrongly displaying as NVICs on some Cortex-M3 parts because
many PIDs appear to be zeroes ... maybe adapter related??
Signed-off-by: David Brownell <db@helium.(none)>
waiting for ZY1000 fifo to idle is now queued as
an asynchronous command. This radically improves
performance when waitIdle() is interspersed with
writes as no readback is required over TCP/IP.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Mask the upper bits after 32-bit reads.
Alsoo revert the ugly changes to use PRIx32; just cast to unsized
integers when printing (two chars not eight).
Signed-off-by: David Brownell <db@helium.(none)>
This reverts the incorrect change made to the arm9 cmd group in commit
d1eca9a74c.
The code now matches the docs and the release notes.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Bugfix and simplify legacy jtag-only defaulting
* Make "dummy" declare its jtag-only nature
* likewise update ft2232
* warn if selection is _required_ (multi-transport adapters),
fixes the "only ft2232 works" bug for at least dummy, with
other drivers going the "legacy" path (submit patches).
Signed-off-by: David Brownell <db@helium.(none)>
String compare against addresses in range 0 or so due
to not checking if there was an active session first.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Classic manifestation of weakness of dangling {
formatting :-) Hard to spot these sort of mistakes visually.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Commit 93f2afa45f dropped the sentinel off the end
of the command_registrants[] array. The loop immediately
following the initialization will walk right off the end.
Signed-off-by: Stacey Sheldon <stac@solidgoldbomb.org>
This adds the guts of a transport framework with initialization,
which should work with current JTAG-only configurations (tested
with FT2232).
Each debug adapter can declare the transports it supports, and
exactly one transport is initialized. (with its commands) in
any given OpenOCD session.
* Define a new "struct transport with init hooks and a few
"transport" subcommands to support it:
"list" ... list the transports configured (just "jtag" for now)
"select" ... makes the debug session use that transport
"init" ... initializes the selected transport (internal)
* "interface_transports" ... declares transports the current interface
can support. (Some will do this from C code instead, when there are
no hardware versioning (or other) issues to prevent it.
Plus some FT2232 tweaks, including a few to streamline upcoming
support for an SWD transport (initially for Luminary adapters).
Eventually src/jtag should probably become src/transport, moving
jtag-specific stuff to transport/jtag.
Signed-off-by: David Brownell <db@helium.(none)>
Revert change made in commit dd88b461da.
Caused segfaults when using ftdi driver under win32.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The code did not transfer the last word in no-ack transfers.
The strange thing is that this did not lead to any
observable errors.
This gaffe was introduced in commit 1f5883ea56
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Review allocation of error numbers in openocd
to avoid overlap.
Put brackets around negative numbers to avoid
issues during macro expansion.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory read/writes to virtual memory, requires that the CPU is
halted.
Use 'phys' option to write to memory while target is running.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when locking the debug access fails on the first try, it's a
bit noisy, so print out message that it succeeded on second try.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add "static" qualifier to private functions.
Move duplicated global declarations from "target/avrt.c"
and "nor/avrf.c" to "target/avrt.h".
Remove unused declarations form "nor/avrf.c".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add "static" qualifier to private functions.
Remove private prototypes from include file.
Remove empty definition of JIM_STATIC.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This fn is an implementation detail of jtag_execute_queue()
that is not to be exposed externally.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
normal code should not call jtag_get_error(), but rather check
the return code from jtag_execute_queue().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When an interactive command fails, the Jim stack trace prints references to
the line in "command.c" where the interpreter was invoked. Since that
location has no relation to the actual command that failed, the information
serves only to add confusion.
By not adding the useless source info to Jim the noise can be reduced,
while still printing a useful trace for nested commands.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add "static" qualifier to private functions.
Function Jim_InterpolateTokens() is private, but has not
been changed to "static".
This function is called only once, so compiler inlines it.
After inline, there is a warning for variable uninitialized.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
(error: declaration of ‘stat’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/sys/stat.h:279: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
(error: declaration of ‘byte’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:50: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
(error: declaration of ‘pHDev’ shadows a global declaration; ../../../../src/jtag/drivers/rlink.c:102: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
in jim.c (error: declaration of ‘boolean’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:52: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
copy & paste error + added FIFO throttling to work around
lockup bug in FPGA.
The arm11 optimisation was introduced post v0.4.0, so this
is not a regression compared to previous release.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Helper ./src/helper/membuf.c is only used in at91sam3.c
1) Replace membuf with LOG_*
2) The original code in sam3_GetDetails() invalidates
all the buffered output of sam3_GetInfo(). The new
code skips sam3_GetInfo() if its output should not
be printed.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I think this fixed an error message where the error
message would show the *previous* uc code rather than
the current unsupported uc code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when the verify failed, it didn't return an error,
which breaks e.g. tcl scripts that rely on this for
exceptions to work.
Found by -Wshadow
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this batch of fixes should be pretty straightforward
rename of 'index' and an 'i' local variable shadowing.
'index' conflicts with a global name.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
found by code inspection. There are many other places in
CFI where LOG_ERROR() should be called similarly...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when a write/unlock/erase failed during write_image, then
an error was not propagated back up so e.g. flash write
image from tcl scripts would not throw an exception.
Also flash filling speed was printed even when the
operation failed. Output is now less confusing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
failure to write to memory was not propagated.
This is an interesting case of broken error handling:
with exceptions we wouldn't have had this at all,
and I also wonder if there is a GCC option to warn
about these kinds of potential bugs.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Parameter "type" of function armv4_5_mmu_translate_va()
is now not used.
Remove the parameter and the "enum" listing its values.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function armv4_5_mmu_translate_va() now properly signals
errors in the return value.
Remove former error handling by setting variable "type" to
value "-1".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function arm920t_write_memory() default return value
should be ERROR_OK.
All cases of local errors are handled immediately and
not further propagated.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 0538081246
introduces a compile time warning:
arm920t.c: In function ‘arm920t_write_memory’:
arm920t.c:567: warning: ‘retval’ may be used uninitialized in this function
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
any read/write operation to memory can fail.
block write algorithm error propagation was broken
in that it would continue after an error was reported
writing data to ram or the algorithm failing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
JTAG_MOVESTATE is misleading, this cmd is only used
for reset.
JTAG_PATHMOVE should be used otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hello,
"stm32x mass_erase" return ERROR_OK even if something goes wrong.
Here is a summary of changes :
* in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error
detected in FLASH_SR register;
* in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the
returned value of stm32x_mass_erase().
I don't know if there is reason to always return ERROR_OK ?
Gaëtan
ETM analyze produced no output when the trace buffer was empty.
This patch provides users with a clue.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Every time command "flash probe #" is executed, memory
structures are re-allocated without preventive free()
of former areas, causing memory leak.
Also, memory allocation does not check return value,
determining segmentation fault in case of out of memory.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
We request a id register read at the end of ahbap_debugport_init
but we never actually run the queue. In some cases this causes a
segfault.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
This second half of the patch is proposed to clean up some GDB keep alive
issues on arm7_9 targets that start up with very slow clocks. If an attempt
is made to write to key registers on the processor with a slow jtag speed,
GDB timeout warnings appear on the console (at least mine) when "reset halt"
or "reset init" commands are issued from the gdb client:
*** BEFORE PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1026). Workaround: increase "set remotetimeout" in GDB
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1027). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1004). Workaround: increase "set remotetimeout" in GDB
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
I added additional keep alive steps in areas that troubleshooting revealed
were causing problems. I only did this however for non-fast write memory
accesses. I don't think most people would be using fast memory accesses to
write to memory when the jtag and system clocks are slow anyway.
If you disagree with my feeling, think there is a more elegant way to handle
the problem, or think the patch will cause other unforeseen problems with
other targets, let me know. As you can see below, the patch does eliminate
the problem on my development station and I suspect that it will benefit
others.
*** AFTER PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
Gary Carlson
Gary Carlson, MSEE
Principal Engineer
Carlson-Minot Inc.
tcl "puts" didn't work because the logging code sensored strings
that did not include a '\n'. The correct thing is to sensor
empty strings, which are used to keep gdb connection alive.
The tcl "puts" code broke apart strings which do contain '\n' in
order to implement the -nonewline argument, which is how it
got hurt by the bug in log.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Øyvind Harboe
Wookey
Spencer Oliver
David Brownell
Oleksandr Tymoshenko
Catalin Patulea
Piotr Esden-Tempski
Thomas Koeller
Fredrik Hederstierna
Michal Demin
sb-sf
Stacey Sheldon
Marc Pignat
Olaf Lüke
Antonio Borneo
Edgar Grimberg
Andreas Fritiofson
Freddie Chopin
gcembed
Jon Povey
Gary Carlson