added simple architecture for vpr version 8
This commit is contained in:
Steve Corey
parent
2208916a95
commit
fa50eef093
|
|
@ -0,0 +1,179 @@
|
||||||
|
<!--
|
||||||
|
Architecture file translated from ifar repository N04K04L01.FC15FO25.AREA1DELAY1.CMOS90NM.BPTM
|
||||||
|
|
||||||
|
Simple architecture file for vpr version 8 consisting of clusters of BLEs, each BLE contains a 4-LUT+FF pair. Delay models from 90nm PTM.
|
||||||
|
-->
|
||||||
|
|
||||||
|
<architecture>
|
||||||
|
|
||||||
|
<!--
|
||||||
|
ODIN II specific config begins
|
||||||
|
Describes the types of user-specified netlist blocks (in blif, this corresponds to
|
||||||
|
".model [type_of_block]") that this architecture supports.
|
||||||
|
|
||||||
|
Note: This simple architecture needs no models defined here. Basic LUTs, I/Os, and flip-flops are not included here as there are
|
||||||
|
already special structures in blif (.names, .input, .output, and .latch) that describe them.
|
||||||
|
-->
|
||||||
|
<models>
|
||||||
|
</models>
|
||||||
|
<!-- ODIN II specific config ends -->
|
||||||
|
|
||||||
|
<!-- Physical descriptions begin -->
|
||||||
|
<layout>
|
||||||
|
<auto_layout aspect_ratio="1.000000">
|
||||||
|
<!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
|
||||||
|
<perimeter type="io" priority="100"/>
|
||||||
|
<corners type="EMPTY" priority="101"/>
|
||||||
|
<!--Fill with 'clb'-->
|
||||||
|
<fill type="clb" priority="10"/>
|
||||||
|
</auto_layout>
|
||||||
|
</layout>
|
||||||
|
<device>
|
||||||
|
<sizing R_minW_nmos="6065.520020" R_minW_pmos="18138.500000"/>
|
||||||
|
<area grid_logic_tile_area="7238.080078"/>
|
||||||
|
<chan_width_distr>
|
||||||
|
<x distr="uniform" peak="1.000000"/>
|
||||||
|
<y distr="uniform" peak="1.000000"/>
|
||||||
|
</chan_width_distr>
|
||||||
|
<switch_block type="wilton" fs="3"/>
|
||||||
|
<connection_block input_switch_name="ipin_cblock"/>
|
||||||
|
</device>
|
||||||
|
<switchlist>
|
||||||
|
<switch type="mux" name="0" R="0.000000" Cin="0.000000e+00" Cout="0.000000e+00" Tdel="7.958000e-11" mux_trans_size="2.074780" buf_size="19.261999"/>
|
||||||
|
<!--switch ipin_cblock resistance set to yeild for 4x minimum drive strength buffer-->
|
||||||
|
<switch type="mux" name="ipin_cblock" R="1516.380005" Cout="0." Cin="0.000000e+00" Tdel="7.362000e-11" mux_trans_size="1.240240" buf_size="auto"/>
|
||||||
|
</switchlist>
|
||||||
|
<segmentlist>
|
||||||
|
<segment freq="1.000000" length="4" type="unidir" Rmetal="0.000000" Cmetal="0.000000e+00">
|
||||||
|
<mux name="0"/>
|
||||||
|
<sb type="pattern">1 1 1 1 1</sb>
|
||||||
|
<cb type="pattern">1 1 1 1</cb>
|
||||||
|
</segment>
|
||||||
|
</segmentlist>
|
||||||
|
|
||||||
|
<complexblocklist>
|
||||||
|
|
||||||
|
<!-- Define I/O pads begin -->
|
||||||
|
<!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
|
||||||
|
<pb_type name="io" capacity="1">
|
||||||
|
<input name="outpad" num_pins="1"/>
|
||||||
|
<output name="inpad" num_pins="1"/>
|
||||||
|
<clock name="clock" num_pins="1"/>
|
||||||
|
|
||||||
|
<!-- IOs can operate as either inputs or outputs.
|
||||||
|
Delays below come from Ian Kuon. They are small, so they should be interpreted as
|
||||||
|
the delays to and from registers in the I/O (and generally I/Os are registered
|
||||||
|
today and that is when you timing analyze them.
|
||||||
|
-->
|
||||||
|
<mode name="inpad">
|
||||||
|
<pb_type name="inpad" blif_model=".input" num_pb="1">
|
||||||
|
<output name="inpad" num_pins="1"/>
|
||||||
|
</pb_type>
|
||||||
|
<interconnect>
|
||||||
|
<direct name="inpad" input="inpad.inpad" output="io.inpad">
|
||||||
|
<delay_constant max="9.492000e-11" in_port="inpad.inpad" out_port="io.inpad"/>
|
||||||
|
</direct>
|
||||||
|
</interconnect>
|
||||||
|
|
||||||
|
</mode>
|
||||||
|
<mode name="outpad">
|
||||||
|
<pb_type name="outpad" blif_model=".output" num_pb="1">
|
||||||
|
<input name="outpad" num_pins="1"/>
|
||||||
|
</pb_type>
|
||||||
|
<interconnect>
|
||||||
|
<direct name="outpad" input="io.outpad" output="outpad.outpad">
|
||||||
|
<delay_constant max="2.675000e-11" in_port="io.outpad" out_port="outpad.outpad"/>
|
||||||
|
</direct>
|
||||||
|
</interconnect>
|
||||||
|
</mode>
|
||||||
|
|
||||||
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
||||||
|
<fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
|
||||||
|
|
||||||
|
<!-- IOs go on the periphery of the FPGA, for consistency,
|
||||||
|
make it physically equivalent on all sides so that only one definition of I/Os is needed.
|
||||||
|
If I do not make a physically equivalent definition, then I need to define 4 different I/Os, one for each side of the FPGA
|
||||||
|
-->
|
||||||
|
<pinlocations pattern="custom">
|
||||||
|
<loc side="left">io.outpad io.inpad io.clock</loc>
|
||||||
|
<loc side="top">io.outpad io.inpad io.clock</loc>
|
||||||
|
<loc side="right">io.outpad io.inpad io.clock</loc>
|
||||||
|
<loc side="bottom">io.outpad io.inpad io.clock</loc>
|
||||||
|
</pinlocations>
|
||||||
|
|
||||||
|
<power method="ignore"/>
|
||||||
|
</pb_type>
|
||||||
|
<!-- Define I/O pads ends -->
|
||||||
|
|
||||||
|
<!-- Define general purpose logic block (CLB) begin -->
|
||||||
|
<pb_type name="clb">
|
||||||
|
<input name="I" num_pins="10"/>
|
||||||
|
<output name="O" num_pins="1"/>
|
||||||
|
<clock name="clk" num_pins="1"/>
|
||||||
|
|
||||||
|
<!-- Describe basic logic element. -->
|
||||||
|
|
||||||
|
<!-- Define 4-LUT mode -->
|
||||||
|
<pb_type name="ble4" num_pb="1">
|
||||||
|
<input name="in" num_pins="4"/>
|
||||||
|
<output name="out" num_pins="1"/>
|
||||||
|
<clock name="clk" num_pins="1"/>
|
||||||
|
|
||||||
|
<!-- Define LUT -->
|
||||||
|
<pb_type name="lut4" blif_model=".names" num_pb="1" class="lut">
|
||||||
|
<input name="in" num_pins="4" port_class="lut_in"/>
|
||||||
|
<output name="out" num_pins="1" port_class="lut_out"/>
|
||||||
|
<!-- LUT timing using delay matrix -->
|
||||||
|
<delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
|
||||||
|
2.253000e-10
|
||||||
|
2.253000e-10
|
||||||
|
2.253000e-10
|
||||||
|
2.253000e-10
|
||||||
|
</delay_matrix>
|
||||||
|
</pb_type>
|
||||||
|
|
||||||
|
<!-- Define flip-flop -->
|
||||||
|
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
||||||
|
<input name="D" num_pins="1" port_class="D"/>
|
||||||
|
<output name="Q" num_pins="1" port_class="Q"/>
|
||||||
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||||
|
<T_setup value="2.160000e-10" port="ff.D" clock="clk"/>
|
||||||
|
<T_clock_to_Q max="1.426000e-10" port="ff.Q" clock="clk"/>
|
||||||
|
</pb_type>
|
||||||
|
|
||||||
|
<interconnect>
|
||||||
|
<direct name="direct1" input="ble4.in" output="lut4[0:0].in"/>
|
||||||
|
<direct name="direct2" input="lut4.out" output="ff.D">
|
||||||
|
<!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
|
||||||
|
<pack_pattern name="ble6" in_port="lut4.out" out_port="ff.D"/>
|
||||||
|
</direct>
|
||||||
|
<direct name="direct3" input="ble4.clk" output="ff.clk"/>
|
||||||
|
<mux name="mux1" input="ff.Q lut4.out" output="ble4.out">
|
||||||
|
</mux>
|
||||||
|
</interconnect>
|
||||||
|
</pb_type>
|
||||||
|
|
||||||
|
<!-- 4-LUT mode definition end -->
|
||||||
|
<interconnect>
|
||||||
|
<!-- Keyword 'complete' indicates a fully connected crossbar to get logical equivalence at inputs of CLB
|
||||||
|
here, the crossbar takes input from the clb and the feedback output from the ble.
|
||||||
|
crossbar output goes to the ble input. -->
|
||||||
|
<complete name="crossbar" input="clb.I ble4[0:0].out" output="ble4[0:0].in">
|
||||||
|
<delay_constant max="5.735000e-11" in_port="clb.I" out_port="ble4[0:0].in" />
|
||||||
|
<delay_constant max="5.428000e-11" in_port="ble4[0:0].out" out_port="ble4[0:0].in" />
|
||||||
|
</complete>
|
||||||
|
<complete name="clks" input="clb.clk" output="ble4[0:0].clk">
|
||||||
|
</complete>
|
||||||
|
<direct name="clbouts1" input="ble4[0:0].out" output="clb.O"/>
|
||||||
|
</interconnect>
|
||||||
|
|
||||||
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 25% of the tracks in a channel -->
|
||||||
|
<fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.25"/>
|
||||||
|
|
||||||
|
<pinlocations pattern="spread"/>
|
||||||
|
|
||||||
|
</pb_type>
|
||||||
|
<!-- Define general purpose logic block (CLB) ends -->
|
||||||
|
|
||||||
|
</complexblocklist>
|
||||||
|
</architecture>
|
||||||
Loading…
Reference in New Issue