From fa50eef093a2e085bb64b659576e10b21d724281 Mon Sep 17 00:00:00 2001
From: Steve Corey <s.corey@utah.edu>
Date: Wed, 11 Jul 2018 13:19:40 -0600
Subject: [PATCH] added simple architecture for vpr version 8

---
 tutorial/v8_example_arch.xml | 179 +++++++++++++++++++++++++++++++++++
 1 file changed, 179 insertions(+)
 create mode 100644 tutorial/v8_example_arch.xml

diff --git a/tutorial/v8_example_arch.xml b/tutorial/v8_example_arch.xml
new file mode 100644
index 000000000..a280fda66
--- /dev/null
+++ b/tutorial/v8_example_arch.xml
@@ -0,0 +1,179 @@
+<!-- 
+      Architecture file translated from ifar repository N04K04L01.FC15FO25.AREA1DELAY1.CMOS90NM.BPTM
+      
+      Simple architecture file for vpr version 8 consisting of clusters of BLEs, each BLE contains a 4-LUT+FF pair.  Delay models from 90nm PTM.
+-->
+
+<architecture>
+
+  <!-- 
+       ODIN II specific config begins 
+       Describes the types of user-specified netlist blocks (in blif, this corresponds to 
+       ".model [type_of_block]") that this architecture supports.
+
+        Note: This simple architecture needs no models defined here. Basic LUTs, I/Os, and flip-flops are not included here as there are 
+        already special structures in blif (.names, .input, .output, and .latch) that describe them.
+  -->
+  <models>
+  </models>
+  <!-- ODIN II specific config ends -->
+
+  <!-- Physical descriptions begin -->
+  <layout>
+    <auto_layout aspect_ratio="1.000000">
+      <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
+      <perimeter type="io" priority="100"/>
+      <corners type="EMPTY" priority="101"/>
+      <!--Fill with 'clb'-->
+      <fill type="clb" priority="10"/>
+    </auto_layout>
+  </layout>
+  <device>
+    <sizing R_minW_nmos="6065.520020" R_minW_pmos="18138.500000"/>
+    <area grid_logic_tile_area="7238.080078"/>
+    <chan_width_distr>
+      <x distr="uniform" peak="1.000000"/>
+      <y distr="uniform" peak="1.000000"/>
+    </chan_width_distr>
+    <switch_block type="wilton" fs="3"/>
+    <connection_block input_switch_name="ipin_cblock"/>
+  </device>
+  <switchlist>
+    <switch type="mux" name="0" R="0.000000" Cin="0.000000e+00" Cout="0.000000e+00" Tdel="7.958000e-11" mux_trans_size="2.074780" buf_size="19.261999"/>
+    <!--switch ipin_cblock resistance set to yeild for 4x minimum drive strength buffer-->
+    <switch type="mux" name="ipin_cblock" R="1516.380005" Cout="0." Cin="0.000000e+00" Tdel="7.362000e-11" mux_trans_size="1.240240" buf_size="auto"/>
+  </switchlist>
+  <segmentlist>
+    <segment freq="1.000000" length="4" type="unidir" Rmetal="0.000000" Cmetal="0.000000e+00">
+      <mux name="0"/>
+      <sb type="pattern">1 1 1 1 1</sb>
+      <cb type="pattern">1 1 1 1</cb>
+    </segment>
+  </segmentlist>
+
+  <complexblocklist>
+
+    <!-- Define I/O pads begin -->
+    <!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
+    <pb_type name="io" capacity="1">
+      <input name="outpad" num_pins="1"/>
+      <output name="inpad" num_pins="1"/>
+      <clock name="clock" num_pins="1"/>
+
+      <!-- IOs can operate as either inputs or outputs.
+          Delays below come from Ian Kuon. They are small, so they should be interpreted as
+          the delays to and from registers in the I/O (and generally I/Os are registered 
+          today and that is when you timing analyze them.
+      -->
+      <mode name="inpad">
+        <pb_type name="inpad" blif_model=".input" num_pb="1">
+          <output name="inpad" num_pins="1"/>
+        </pb_type>
+        <interconnect>
+          <direct name="inpad" input="inpad.inpad" output="io.inpad">
+            <delay_constant max="9.492000e-11" in_port="inpad.inpad" out_port="io.inpad"/>
+          </direct>
+        </interconnect>
+
+      </mode>
+      <mode name="outpad">
+        <pb_type name="outpad" blif_model=".output" num_pb="1">
+          <input name="outpad" num_pins="1"/>
+        </pb_type>
+        <interconnect>
+          <direct name="outpad" input="io.outpad" output="outpad.outpad">
+            <delay_constant max="2.675000e-11" in_port="io.outpad" out_port="outpad.outpad"/>
+          </direct>
+        </interconnect>
+      </mode>
+
+      <!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
+
+      <!-- IOs go on the periphery of the FPGA, for consistency, 
+           make it physically equivalent on all sides so that only one definition of I/Os is needed.
+           If I do not make a physically equivalent definition, then I need to define 4 different I/Os, one for each side of the FPGA
+      -->
+      <pinlocations pattern="custom">
+        <loc side="left">io.outpad io.inpad io.clock</loc>
+        <loc side="top">io.outpad io.inpad io.clock</loc>
+        <loc side="right">io.outpad io.inpad io.clock</loc>
+        <loc side="bottom">io.outpad io.inpad io.clock</loc>
+      </pinlocations>
+
+      <power method="ignore"/>			
+    </pb_type>
+    <!-- Define I/O pads ends -->
+
+    <!-- Define general purpose logic block (CLB) begin -->
+    <pb_type name="clb">
+      <input name="I" num_pins="10"/>
+      <output name="O" num_pins="1"/>
+      <clock name="clk" num_pins="1"/>
+
+      <!-- Describe basic logic element. -->
+
+      <!-- Define 4-LUT mode -->
+      <pb_type name="ble4" num_pb="1">
+        <input name="in" num_pins="4"/>
+        <output name="out" num_pins="1"/>
+        <clock name="clk" num_pins="1"/> 
+
+        <!-- Define LUT -->
+        <pb_type name="lut4" blif_model=".names" num_pb="1" class="lut">
+          <input name="in" num_pins="4" port_class="lut_in"/>
+          <output name="out" num_pins="1" port_class="lut_out"/>
+          <!-- LUT timing using delay matrix -->
+          <delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
+            2.253000e-10
+            2.253000e-10
+            2.253000e-10
+            2.253000e-10
+          </delay_matrix>
+        </pb_type>
+
+        <!-- Define flip-flop -->
+        <pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
+          <input name="D" num_pins="1" port_class="D"/>
+          <output name="Q" num_pins="1" port_class="Q"/>
+          <clock name="clk" num_pins="1" port_class="clock"/>
+          <T_setup value="2.160000e-10" port="ff.D" clock="clk"/>
+          <T_clock_to_Q max="1.426000e-10" port="ff.Q" clock="clk"/>
+        </pb_type>
+
+        <interconnect>
+          <direct name="direct1" input="ble4.in" output="lut4[0:0].in"/>
+          <direct name="direct2" input="lut4.out" output="ff.D">
+            <!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
+            <pack_pattern name="ble6" in_port="lut4.out" out_port="ff.D"/>
+          </direct>
+          <direct name="direct3" input="ble4.clk" output="ff.clk"/>                    
+          <mux name="mux1" input="ff.Q lut4.out" output="ble4.out">
+          </mux>
+        </interconnect>
+      </pb_type>
+
+      <!-- 4-LUT mode definition end -->
+      <interconnect>
+        <!-- Keyword 'complete' indicates a fully connected crossbar to get logical equivalence at inputs of CLB 
+             here, the crossbar takes input from the clb and the feedback output from the ble.
+             crossbar output goes to the ble input. -->
+        <complete name="crossbar" input="clb.I ble4[0:0].out" output="ble4[0:0].in">
+          <delay_constant max="5.735000e-11" in_port="clb.I" out_port="ble4[0:0].in" />
+          <delay_constant max="5.428000e-11" in_port="ble4[0:0].out" out_port="ble4[0:0].in" />
+        </complete>
+        <complete name="clks" input="clb.clk" output="ble4[0:0].clk">
+        </complete>
+        <direct name="clbouts1" input="ble4[0:0].out" output="clb.O"/>
+      </interconnect>
+
+      <!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 25% of the tracks in a channel -->
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.25"/>
+
+      <pinlocations pattern="spread"/>
+
+    </pb_type>
+    <!-- Define general purpose logic block (CLB) ends -->
+
+  </complexblocklist>
+</architecture>