The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This driver is used with the ESP32 chips which has builtin USB-JTAG
interface. e.g. with ESP32-C3, ESP32-S3
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61
Reviewed-on: https://review.openocd.org/c/openocd/+/6943
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/interface | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7bd6a628e9e153fc477cddf9b97087a39ec48aa7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7029
Tested-by: jenkins
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line.
Change-Id: I3992856eeb28b333c38d010ef286e22471ede263
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7026
Tested-by: jenkins
OpenOCD project is switching to SPDX tags.
Replace the few FSF boilerplate in tcl folder.
Change-Id: I15b146eb77cc491ed7355178f684f3e76fc763b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7025
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32-S2 is a single core Xtensa chip.
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I2fb32978e801af5aa21616c581691406ad7cd6bb
Reviewed-on: https://review.openocd.org/c/openocd/+/6940
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tigard[1] is an FT2232H-based development tool designed for ease of use
with many different protocols and targets. It includes a JTAG header
wired to channel B, with labeled pins for the four required signals as
well as nTRST and nSRST, which are connected through an output buffer to
BDBUS4 and BDBUS5 respectively.
Add an interface config for Tigard. I wrote it by referencing the Tigard
schematic and tested it by debugging a couple of RISC-V development
boards.
[1] https://github.com/tigard-tools/tigard
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Change-Id: I34df9f72538ba1e40ad53b568c9cdca96ae4b082
Reviewed-on: https://review.openocd.org/c/openocd/+/6952
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/nor/atsame5: add LAN9255 devices
Support Microchip LAN9255 devices with embedded SAME53J MCU.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Change-Id: Ia811c593bf7cf73e588d32873c68eb67c6fafad7
Reviewed-on: https://review.openocd.org/c/openocd/+/6811
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: Add EVB-LAN9255 config
Config for EVB-LAN9255, tested using Atmel-ICE debugger on J10
connector.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Change-Id: I8bcf779e9363499a98aa0b7d10819c53da6a19e7
Reviewed-on: https://review.openocd.org/c/openocd/+/6812
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* aarch64: support for aarch32 ARM_MODE_UND
Fix:
unrecognized psr mode: 0x1b
cannot read system control register in this mode: (UNRECOGNIZED : 0x1b)
Change-Id: I4dc3e72f90d57e52c0fe63cb59a7529a398757b3
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: Ifa5d21ae97492fde9e8c79ee7d99d8a2a871b1b5
Reviewed-on: https://review.openocd.org/c/openocd/+/6808
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Combine register lists of smp targets.
This is helpful when you want to pretend to gdb that your heterogeneous
multicore system is homogeneous, because gdb cannot handle heterogeneous
systems. This won't always works, but works fine if e.g. one of the
cores has an FPU while the other does not. (Specifically, HiFive
Unleashed has 1 core with no FPU, plus 4 cores with an FPU.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I05ff4c28646778fbc00327bc510be064bfe6c9f0
Reviewed-on: https://review.openocd.org/c/openocd/+/6362
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* semihosting: use open mode flags from GDB, not from sys/stat.h
Values defined in sys/stat.h are not guaranteed to match
the constants defined by the GDB remote protocol, which are defined in
https://sourceware.org/gdb/onlinedocs/gdb/Open-Flags.html#Open-Flags.
On my local system (Manjaro 21.2.1 x86_64), for example, O_TRUNC is
defined as 0x40, whereas GDB requires it to be 0x400,
causing all "w" file open modes to misbehave.
This patch has been tested with STM32F446.
Change-Id: Ifb2c740fd689e71d6f1a4bde1edaecd76fdca910
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* semihosting: User defined operation, Tcl command exec on host
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/smp: use a struct list_head to hold the smp targets
Instead of reinventing a simply linked list, reuse the list helper
for the list of targets in a smp cluster.
Using the existing helper, that implements a double linked list,
makes trivial going through the list in reverse order.
Change-Id: Ib36ad2955f15cd2a601b0b9e36ca6d948b12d00f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6783
Tested-by: jenkins
* helper/list: add list_for_each_entry_direction()
Use a bool flag to specify if the list should be forward or
backward iterated.
Change-Id: Ied19d049f46cdcb7f50137d459cc7c02014526bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6784
Tested-by: jenkins
* target/riscv: revive 'riscv resume_order'
This functionality was lost in [1], which was merged as commit
615709d140 ("Upstream a whole host of RISC-V changes.").
Now it works as expected again.
Add convenience macro foreach_smp_target_direction().
Link: [1] https://github.com/riscv/riscv-openocd/pull/567
Change-Id: I1545fa6b45b8a07e27c8ff9dcdcfa2fc4f950cd1
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6785
Tested-by: jenkins
* doxygen: fix some function prototype description
Change-Id: I49311a643ea73143839d2f6bde976cfd76f8c67f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6830
Tested-by: jenkins
* Cadence virtual debug interface (vdebug) integration
Change-Id: I1bc105b3addc3f34161c2356c482ff3011e3f2cc
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6097
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: Include thread name as XML attribute
Explicitly providing a thread name in the "thread" element produces
better thread visualizations in downstream tools like IDEs.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I102c14ddb8b87757fa474de8e3a3f6a1cfe10d98
Reviewed-on: https://review.openocd.org/c/openocd/+/6828
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix small memory leak.
See https://github.com/riscv/riscv-openocd/pull/672
Change-Id: Ia11ab9bcf860f770ea64ad867102c74b898f6b66
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6831
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* server: remove remaining crust from dropped eCos code
Commit 39650e2273 ("ecosboard: delete bit-rotted eCos code") has
removed eCos code but has left some empty function that was used
during non-eCos build to replace eCos mutex.
Drop the functions and the file that contain them.
Change-Id: I31bc0237ea699c11bd70921660f960ee406ffa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6835
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: threadx: Add hla_target support for ThreadX
Tested with an AZ3166 dev board (which uses the STM32F412ZGT6) running
the Azure RTOS ThreadX demonstration system.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I44c8f7701d9f1aaa872274166321cd7d34fb1855
Reviewed-on: https://review.openocd.org/c/openocd/+/6829
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* .gitmodules: switch away from repo.or.cz
The host repo.or.cz is often offline, creating issues for cloning
and building OpenOCD from scratch.
Already 'jimtcl' developer has dropped repo.or.cz, triggering the
OpenOCD commit 861e75f54e ("jimtcl: switch to github").
Change also the link of the remaining submodules 'git2cl' and
'libjaylink' to their respective main repository.
Change-Id: Ib513237427635359ce36a480a8f2060e2fb12ba4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6834
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
* flash/nor/stm32f2x: Fix erase of bank 2 sectors
This commit corrects the erase function for stm32f2x when dealing with
sectors in bank 2, for STM32F42x/43x devices with 1MB flash.
On STM32F42x/43x with 1MB flash in dual bank configuration, the sector
numbering is not consecutive. The last sector in bank 1 is number 7, and
the first sector in bank 2 is number 12.
The sector indices used by openocd, however, _are_ consecutive (0 to 15
in this case). The arguments "first" and "last" to stm32x_erase() are of
this type, and so the logic surrounding sector numbers needed to be
corrected.
Since the two banks in dual bank mode have the same number of sectors, a
sector index in bank 2 is larger than or equal to half the total number
of sectors.
Change-Id: I15260f8a86d9002769a1ae1c40ebdf62142dae18
Signed-off-by: Simon Johansson <ampleyfly@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6810
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* target/cortex_m: fix target_to_cm() helper
The third parameter of container_of() should point to the same member
as target->arch_info points to, struct arm.
It worked just because struct arm is the first member in
struct armv7m_common.
If you move arm member from the first place, OpenOCD fails heavily.
Change-Id: I0c0a5221490945563e17a0a34d99a603f1d6c2ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6749
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/armv7m,cortex_m: introduce checked arch_info cast routines
target_to_armv7m() and target_to_cm() do not match the magic number
so they are not suitable for use outside of target driver code.
Add checked versions of pointer getters. Match the magic number
to ensure the returned value points to struct of the correct type.
Change-Id: If90ef7e969ef04f0f2103e0da29dcbe8e1ac1c0d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6750
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/cortex_m: add Cortex-M part number getter
The getter checks the magic numbers in arch_info to detect eventual
type mismatch.
Change-Id: I61134b05310a97ae9831517d0516c7b4240d35a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6751
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* flash/nor/stm32xx: fix segfault accessing Cortex-M part number
Some of STM32 flash drivers read Cortex-M part number from
cortex_m->core_info.
In corner cases the core_info pointer was observed uninitialised
even if target_was_examined() returned true. See also [1]
Use the new and safe helper to get Cortex-M part number.
While on it switch also target_to_cm()/target_to_armv7m() to the safe
versions. This prevents a crash when the flash bank is misconfigured
with non-Cortex-M target.
Add missing checks for target_was_examined() to flash probes.
[1] 6545: fix crash in case cortex_m->core_info is not set
https://review.openocd.org/c/openocd/+/6545
Change-Id: If2471af74ebfe22f14442f48ae109b2e1bb5fa3b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: f5898bd93f (flash/stm32fxx.c: do not read CPUID as this info is stored in cortex_m_common)
Reviewed-on: https://review.openocd.org/c/openocd/+/6752
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* cpld: altera-epm240: Add additional IDCODEs
This adds some additional IDCODEs from the datasheet. It also adds
support for customizing the tap name.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I7cda10b92c229b61836c12cd9ca410de358ede2e
Reviewed-on: https://review.openocd.org/c/openocd/+/6846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cpld: altera-epm240: Increase adapter speed
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: Add support for ls1088a
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: ls1088a: Add service processor
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* board: Add NXP LS1088ARDB
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: fix double free
Commit 6541233aa7 ("Combine register lists of smp targets.")
unconditionally assigns the output pointers of the function
smp_reg_list_noread(), even if the function fails and returns
error.
This causes a double free from the caller, that has assigned NULL
to the pointers to simplify the error handling.
Use local variables in smp_reg_list_noread() and assign the output
pointers only on success.
Change-Id: Ic0fd2f26520566cf322f0190780e15637c01cfae
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6852
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* gdb_server: check target examined while combining reg list
Commit 6541233aa7 ("Combine register lists of smp targets.")
assumes that all the targets in the SMP cluster are already
examined and unconditionally call target_get_gdb_reg_list_noread()
that will in turn return error if the target is not examined yet.
Skip targets not examined yet.
Add an additional check in case the register list cannot be built,
e.g. because no target in the SMP cluster is examined. This should
never happen, but it's better to play safe.
Change-Id: I8609815c3d5144790fb05a870cb0c931540aef8a
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6853
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* flash/stm32l4x: fix maybe-uninitialized compiler error
using gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0 we get:
error: ‘retval’ may be used uninitialized in this function
fixes: 13cd75b6ec (flash/nor/stm32xx: fix segfault accessing Cortex-M part number)
Change-Id: I897c40c5d2233f50a5385d251ebfa536023e5cf7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix build.
Change-Id: Ia60246246dd859d75659a43d1c59588dbb274d46
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Co-authored-by: Julien Massot <julien.massot@iot.bzh>
Co-authored-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Co-authored-by: Zoltán Dudás <zedudi@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Jacek Wuwer <jacekmw8@gmail.com>
Co-authored-by: Ben McMorran <bemcmorr@microsoft.com>
Co-authored-by: Simon Johansson <ampleyfly@gmail.com>
Co-authored-by: Tomas Vanek <vanekt@fbl.cz>
Co-authored-by: Sean Anderson <sean.anderson@seco.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Also rename ftdi_oscan1_mode command which only exists in our branch.
Change-Id: Ie9b28f228b1fd984244edb8162d552104d28e462
Signed-off-by: Tim Newsome <tim@sifive.com>
The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
The driver jlink defines the command 'jlink serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: in former code the commands 'jlink serial' and 'jlink usb'
were mutually exclusive; running one of them would invalidate the
effect of a previous execution of the other. The new code gives
priority to 'adapter serial', even if executed before 'jlink usb'.
Change-Id: I920b0c136716f459b6fd6f7da8a01a7fa1ed389f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6656
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The driver xds110 defines the command 'xds110 serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: the original command 'xds110 serial' used a complex and
undocumented conversion of the serial number through multibyte
string, wide-character string and C cast. The XDS110 I can access
and the lsusb dumps available through Google don't show any
exotic USB serial that require such conversion. The original
developer doesn't remember any constraint that mandates such
conversion (see comments in https://review.openocd.org/4322/).
The conversion is removed by this patch.
Change-Id: I38909918079b2c1797ad85ebec2fea1b33743606
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6655
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver kitprog defines the command 'kitprog_serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I844cb815af01137392b6d12e1b5972fc77ac092d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6652
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver ftdi defines the command 'ftdi serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: Ia5b1f325b9fab8f58b5ea70f8b807e50b148b939
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6651
Tested-by: jenkins
The driver cmsis_dap defines the command 'cmsis_dap_serial' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I88e2d4de360a6c6f23529bb18494962a267250df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6649
Tested-by: jenkins
The driver aice defines the command 'aice serial' to specify the
serial string of the adapter, but actually does not use this value
in the code.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I892e0a4e1b41a7a87adf54a5736abf7419f32979
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6648
Tested-by: jenkins
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for ECP5 FPGA targets and board based on this chips:
Radiona ULX3S and Lambdaconcept ECPIX-5
Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6112
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tim Newsome
Antonio Borneo
Tomas Vanek
mrv96
Steve Marple
Ian Thompson
Jae Hyun Yoo
Erhan Kurubas
Thomas Hebb
Jacek Wuwer
Andreas Sandberg
Oleksij Rempel
Ranjith Chandran
Marc Schink
Matthew Mets
Patrick Stewart