This patch adds Micrel's KS869x target. The configuration was taken from
http://www.mmnt.net/db/0/0/www.micrel.com/ethernet/8695 - Micrel's
FTP server i.e. their OpenOCD 7.0 package.
The only change compared to the original file is the removal of
reset configuration, as it belongs to the board configuration.
Change-Id: Ic8509aa5fe5ce3166a3129e1c055280a3b2b9312
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-on: http://openocd.zylin.com/2125
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b
Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add configuration file for General Plus GP326XXXA series. Tested on
GP326833A on GPC-1737B board.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I1ad0e22598b01317bbc823870a7a262e9192c595
Reviewed-on: http://openocd.zylin.com/2058
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Also add the board to the firmware recovery script.
Change-Id: I4f9c895dae171df7249e3b1c0563b288518b9fe0
Signed-off-by: Lee Bowyer <lee@sodnpoo.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SoftDevice stack ihex binary, provided by Nordic expects being able to
write data necessary for its correct operation at the adresses inside UICR.
This patch exposes UICR region of flash as a second bank on the MCU to
facilitate that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Idbc140b8de027f60655f78043877b7c054eb06f9
Reviewed-on: http://openocd.zylin.com/2013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds support for the am43xx SoC and the AM437x GP EVM and AM438x
ePOS EVM.
Change-Id: I09cbb09072f38e0e08fdd520dedb6e67d45056be
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2047
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
instead of replicating icepick_d_tapenable in many of TI's newer
platforms, we can move to icepick.cfg and just call it from board TCL
configuration file. This is similar to the C but has a few changes we
need to make.
Change-Id: I0ab48005ccd66cd5b67b919fb5e3b462288f211d
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2030
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
From testing this target does not seem to support using SYSRESETREQ, change
the default to the safe VECTRESET.
This target also has other reset issues (srst not working) that will be
addressed in another patch.
Change-Id: Icfc78347dc71aa3a062ddea63190a818d7fbc760
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1995
Tested-by: jenkins
Reviewed-by: Angus Gratton <gus@projectgus.com>
Atmel's SAM3 and SAM4 processor families are very close to each other
in many respects. However, so far, only the SAM4 target script
contained the magic to allow using SWD, while SAM3 was tied to JTAG
only. This e.g. prevented the CMSIS-DAP driver from accessing SAM3
devices as it only uses SWD transport (by now).
The patch pulls all the things from the SAM4 target script that are
also applicable to SAM3 devices. With the patch, an Atmel CMSIS-DAP
debugger (Atmel-ICE) was proven to be able to successfully attach to a
SAM3S-EK evaluation kit. I also cross-checked that accessing through
a SAM-ICE (Segger J-Link) still works with the patch.
Change-Id: I20dafbff8e1e9f967da950e48a56205586eeef8d
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2046
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for Broadcom's dual A9 mobile SoC and its reference board.
Change-Id: Ia145b120043bddc89c44726066023154ae390788
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-on: http://openocd.zylin.com/1926
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
flash: at91sam4: add support for the SAMG53 family (this also covers the
SAMG51). The SAMG5x parts have an EEFC (enhanced embedded flash controller)
which seems to be identical to the EFC that the sam4 driver supports.
Add a script for the Xplained Pro G53 board, this has the onboard CMSIS-DAP
debugger and a SAMG53N19. Tested on this board and chip combination.
Change-Id: I12af50402cd2069b3c7380d92e6fe54816d6c045
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1974
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Intel Quark X10xx SoC debug support added
Lakemont version 1 (LMT1) is the x86 core in Quark X10xx SoC
Generic x86 32-bit code is in x86_32_common.c/h
Change-Id: If2bf77275cd0277a82558cd9895b4c66155cf368
Signed-off-by: adrian.burns@intel.com
Reviewed-on: http://openocd.zylin.com/1829
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Originally the LPC17xx user guide (UM10360 Rev 2) stated that SYSRESETREQ
was not supported, so this was the default cortex_m reset mode.
Rev 3 of the same user guide states that it is now supported.
This has been verified on a LPC1768 mbed platform, previously I have not
tested this functionality.
Change-Id: I4858248903981a1c93ce75016e67c9e02702fcc5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1892
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds a new NOR Flash driver, "at91samd", which supports the
built-in Flash on Atmel's D-series Cortex M MCUs, starting with the D20.
Parts and their geometry are detected automatically using the DSU and
lookup schemes described in the D20 document, 42129F–SAM–10/2013.
Future D-series variants and families should presumably use this
controller as well (possibly with minor changes and improvements).
Tested on the SAMD20 Xplained Pro board, for which we also add the
corresponding Flash configuration.
Change-Id: Id8d3dd601e9f53121682d1a1190d0be4ea3b83eb
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1684
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a new NOR Flash driver, "at91sam4l", which supports the
built-in Flash on Atmel's low-power SAM4L family of Cortex M4 MCUs.
Parts and their geometry are detected automatically using the Chip ID
and lookup schemes described in document 42023E–SAM–07/2013.
Tested on AT91SAM4LC4CA via the SAM4L XPlained Pro development kit.
Change-Id: If73499dee92cc8ce231845244ea25c6984f6cecd
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1639
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These kits feature a CMSIS-DAP compliant debugger and so have been added
as part of the pending support.
Currently the flash drivers for the L8 and D20 are wip.
One issue this implementation of CMSIS-DAP raised is that it supports
512byte HID reports, however using the current HIDAPI we have no cross platform
way of querying this info. Long term we plan to add this support to HIDAPI.
Change-Id: Ie8b7c871f58a099d963cd71a9f8a0105a38784e9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1625
Tested-by: jenkins
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
Tested flashing a real v1.1 device.
Change-Id: Ie0d202b9fded8b92e731d93e0ef17be415a75fc8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1852
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".
The RAM setup is not done as it would require considerable efforts
without much practical gain.
The only issue I noticed so far is that "reset" doesn't actually reset
the chip.
Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.
Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.
Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* openocd.berlios.de -> openocd.sourceforge.net
* Update link to AM/DM37x Technical Reference Manual (ver R)
* "ICEpick" is properly spelled "ICEPick" according to TI
Change-Id: Ie04458e82c97ef766ec03bd9b9f27edadf5d1cb2
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1856
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The set command was missing the $ prefix on the SJC_TAPID variable
and so would fail if SJC_TAPID was set
Change-Id: Ib9af58f5188bd8a2bc3f888309f203d624476c27
Signed-off-by: Alex Murray <alex.murray@cohdawireless.com>
Reviewed-on: http://openocd.zylin.com/1811
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on Nemuisan Tokusei's. Untested, but original config was reported
to work ok.
Change-Id: Ic991dce55bfca266880081fe2bbd9e6e263b0fc0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1803
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
all other at91 cfg files already has this fix.
It also fix "No flash at address 0x...." error when JTAG chain consist of
more than one at91sam7sx cores during attempt to flash other than first mcu
in chain.
Change-Id: I7785d9103d0fc494b6a823e2c73f850373ffe112
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1812
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32F42xxx & STM32F43xxx series boudary scan TAP-ID are differ from
STM32F405xx/07xx & STM32F415xx/17xx.
And Section number was also fixed for RM0090 rev5.
Tested on a STM32F427IIT6 and STM32F429ZIT6.
Change-Id: Ie9c54c55b97b9c396ace752d94ea2ad916cc8479
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1808
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a Cortex-M1 controller targetting aviation appliances.
Contributed (and live-tested) by 8daemon.
Change-Id: I133d6122cf6492b51ddbdbd800c16ba121d51bf3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1818
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the TMS570 Cortex-R4 MCU from TI and their USB stick
development kit, TMDX570LS31USB. Tested attaching, reset/halt/run, and
reading and writing memory and registers.
Change-Id: I12d779cef0c2b834f9bcf722307f35677cc4bd8f
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1788
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some boards might have RCLK omitted from the JTAG connector and if the
interface claims support for it, OpenOCD will end up trying to use
RCLK while it's actually impossible.
This is a "cd tcl/target; sed -i s/jtag_rclk/adapter_khz/g *" patch.
Change-Id: Iee7337107bc1457966b104389ba9db75a9c860b4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1695
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Initial support for using the jtag interface to the Marvell Armada 370
family of SoCs.
Change-Id: Id823a567e8805ac622c3c330bc111297c1dae37e
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-on: http://openocd.zylin.com/1690
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The smallest available RAM size for this family is 2K, set this as the
default. Issue reported by quitte on IRC.
Change-Id: I3318f7f268f7681ffe2cddab61820f4b94c4e5fd
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1559
Tested-by: jenkins
This commit adds two tcl configuration files, one for the Altera
Cyclone V SoC series, and one for the SoCkit development board.
The board configuration is able to halt and resume the cpu cores,
and dump register contents etc. It has not been fully tested, however.
Change-Id: Id3f18c3408975cf986a5f5aec410b5b13240c35e
Signed-off-by: Brad Riensche <brad.riensche@gmail.com>
Reviewed-on: http://openocd.zylin.com/1494
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds example config and flash driver for russian Cortex-M3
microcontroller model.
Run-time tested on MDR32F9Q2I evaluation board; the flash driver
should be compatible with MDR32F2x (Cortex-M0) too but I lack hardware
to test.
There're no status bits at all, the datasheets specifies some delays
for flash operations instead. All being in <100us range, they're hard
to violate with JTAG, I hope. There're also no flash identification
registers so the flash size and type has to be hardcoded into the
config.
The flashing is considerably complicated because the flash is split
into pages, and each page consists of 4 interleaved non-consecutive
"sectors" (on MDR32F9 only, MDR32F2 is single-sectored), so the
fastest way is to latch the page and sector address and then write
only the part that should go into the current page and current sector.
Performance testing results with adapter_khz 1000 and the chip running
on its default HSI 8MHz oscillator:
When working area is specified, a target helper algorithm is used:
wrote 131072 bytes from file testfile.bin in 3.698427s (34.609 KiB/s)
This can theoretically be sped up by ~1.4 times if the helper
algorithm is fed some kind of "loader instructions stream" to allow
sector-by-sector writing.
Pure JTAG implementation (when target memory area is not available)
flashes all the 128k memory in 49.5s.
Flashing "info" memory region is also implemented, but due to the
overlapping memory addresses (resulting in incorrect memory map
calculations for GDB) it can't be used at the same time, so OpenOCD
needs to be started this way: -c "set IMEMORY true" -f
target/mdr32f9q2i.cfg
It also can't be read/verified because it's not memory-mapped anywhere
ever, and OpenOCD NOR framework doesn't really allow to provide a
custom handler that would be used when verifying.
Change-Id: I80c0632da686d49856fdbf9e05d908846dd44316
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1532
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Austriancoder on IRC reports getting this ID on his board.
Change-Id: Ie859f0ee422e18fdb94bf817cdd2b41d15b968da
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1533
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Pull the jtag_rtck setting from imx51.cfg and imx53.cfg . Since
not all boards using these CPUs do support RTCK signal, move the
configuration of RTCK into board files.
Change-Id: I632c5d38e00ada8779a451cd26428fd122452001
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1460
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Ignore version of Boundary Scan TAP in newer revisions of the str9.
Change-Id: I6e205f8c731f07078c469e686025857c180f3a6d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1436
Tested-by: jenkins
Add target code for Andes targets.
Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d9ba56c295 did a bunch of
renaming of cortex_a8 to cortex_a, including the names in config
files. However that introduced a regression as the name in target_type
struct remained unchanged.
This adds the last missing bit: actual renaming of the target name as
understood by OpenOCD.
Also change the (hopefully) last instance of using it in the supplied
config files, namely from imx6.cfg.
Change-Id: Ib9289fc6d946630133ec6e36c20015ccb50acf61
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1420
Tested-by: jenkins
Reviewed-by: Chris Johns <chrisj@rtems.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is needed for configs that might be used with the cheapest
STM32F100 parts that have only 4kB SRAM.
Restrictions for the other STM32 families are verified to be set
appropriately.
Change-Id: I1ad2370435015604db9f27c1a76c153480311a28
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1378
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to reports of newer targets using a updated version of the ICEPick tap
rather than add another tapid we ignore the tap version.
Also see Trac 49 for details.
Change-Id: Ic78414c54af2545c817e1bb2c860970c1b587259
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1373
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
As requested, here is the target configuration that I'm using for an
STLink-V2-attached STM32W108C8. For some reason, it only seems to work
with "reset_config trst_only".
Change-Id: Icbff4f83343e1f505d8afdfc53ff6f8b7496cac9
Signed-off-by: Ben Nahill <bnahill@gmail.com>
Reviewed-on: http://openocd.zylin.com/1347
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By default pic32mx starts after any reset with 1 wait state for RAM access/exec.
It can be changed to 0 wait states by clearing the BMXWSDRM bit (bit 6) in BMXCON register.
With 0 wait states near doubles the execution speed. CRC check sum can be done much faster
increasing verify_image speed. Fast data transfer also works with a bit higher scan rate, up to 1500 Khz.
This option can be set at any time with
mww 0xbf882004 0x40
or cleared with
mww 0xbf882008 0x40.
Some numbers for FTDI/HS with current devel code and a elf file:
Core clock / wait states verify_image speed
------------------------------------|------------------------------
4 Mhz / 1 21 KiB/s
4 Mhz / 0 36 KiB/s
8 Mhz / 1 37 KiB/s
8 Mhz / 0 57 KiB/s
Change-Id: I4092ad0f3753f72f77108718d0ed3a3ab84e3b23
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1141
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This change adds a simple target configuration for Freescale
single/dual/quad core i.MX6 SoCs, only one core is configured by default.
Change-Id: I853dd27f4c6765b7f731be2ddea82e85d496c6a4
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-on: http://openocd.zylin.com/1135
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch change the default reset config from SYSRESETREQ to the working
VECTRESET.
Change-Id: I21a9a74b9c0c68cfa3a6e6dac9b123acc98a93cb
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1186
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update adds support for the STM32Lx 384kb dual bank flash. Previously there was a problem when writing an
image that was larger than 192Kb. That lead to openocd printing out two error messages like
"Error: access denied / write protected" and "Error: invalid program address". The reason was that the stm32lx
driver tried to write half pages which overlapped into the next flash bank.
A new configuration file stm32lx_dual_bank.cfg can be used for stm32lx chips with dual bank flash (256kb or 384kb devices).
A sanity check was added for probed flash size values to fix the issue seen on some ST samples that answered incorrectly.
Change-Id: I69e25131983d88613be8606b438f98870c5f1e52
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The smallest pert in the family has 10k RAM, so use that as a default
for the working area.
Change-Id: I78be0d14a254c109ac15a7163552c6132f810416
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1005
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Switch to using the internal HSI when a reset init is called, this also
matches the std stm32l cfg.
Read (verify) speed is increased from 17 to 120 KiB/s.
Change-Id: Ic94ba85949ffdefa17b7be45eef14e30f941d107
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1004
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
As part of the switch to using the hla for the stlink interface we rename
the cmds to a more generic name.
Update scripts to match new names.
Also add handlers for deprecated names.
Change-Id: I6f00743da746e3aa13ce06acfdc93c8049545e07
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/921
Tested-by: jenkins
As for openocd 0.6.0-rc2 the function mips32_pracc_fastdata_xfer()
should now work at a scan frequency up to 1200Khz.
Mainly usefull to increase programming speed.
Also verify_image should be slightly faster.
Change-Id: I1e9b2be73690a4597e2f6ba069c1205026850f07
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/805
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added a new configuration file for LPC18xx based boards, such as
HitexLPC1850RevA Evaluation Board, and all other based on the
same microcontroller by NXP.
Change-Id: I68c3827be535b6d09a5c70b6d57191937d00354d
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/930
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the target supports SYSRESETREQ make sure we use that as the default
if srst is not fitted/configured.
Change-Id: I24c907493134506320e69c1218702930629c1cdc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/792
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
- Moved variant-independent code to lpc17xx.cfg, which will be included from
lpc17??.cfg files automatically.
- lpc1768.cfg filled with variant-dependent code.
Change-Id: I7dabe6ed7da7be640ed38c13aaaa096b8796d9a0
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/675
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These were deprecated in commit 69ac20a.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I047872f8cd61b42aaca6588ab75566219e4a3f5d
Reviewed-on: http://openocd.zylin.com/741
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add support for the new stm32f3x family from stmicro:
http://www.st.com/stm32f3
Change-Id: Icd1db95bb2767d9c0ecef24deefa92b4fdaa4f14
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/735
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Seems like an esthetic change, but it will allow easy support for
other lpc17xx devices.
Change-Id: I2cb953ce1afdd82f6ca65b38d5557a28416f895e
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the TI Calypso CPU to the configuration files.
Change-Id: Ieb462960391c4a2c630d7a83699c3b6e8162ace9
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/630
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These events have been deprecated for a number of years, update any
remaining scripts to the new events.
Change-Id: Ic31ff388545ac8b3a500045699ca92c541b13f12
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/634
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
The smallest stm32f0 has 4k sram, so use this as the default.
Change-Id: I9097be9608da92b1b9da504e5bacc1280c86907a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/603
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This enable the user or board config to override the parameters
passed to stm32_stlink.cfg.
Required to fix a incorrect working area bug with the stm32vldiscovery.
Change-Id: I40a4f7913ff37d577d44b1f23befccf0317080a1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/597
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this patch adds the initial support for the omap4460 es1.0
version which is similar to the omap4430 and used on the
pandaboard-es.
Change-Id: If885f7d9f8809929bd799786b539e4f499fa3478
Signed-off-by: David Anders <danders.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/572
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This adds support for the STM32F4 target and the STM3241G Eval Board, in
both standalone and using the onboard STLINK.
Change-Id: I62f8908b5880568b2b36c78a78f94c40861ff335
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/540
Tested-by: jenkins
The SAM3A/X processors that were released thus far is either
a SAM3A/X(4) - 256K, or a SAM3A/X(8) - 512K device. Thus
the config files are per variant, and not per device.
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Change-Id: I84d26d044e810eb428b1d6287907ea3bf8364c73
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/522
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Split out functions specific to the AM335x SOC into the target directory and simplified the board config
file. This should allow one to quickly create new configs for boards based on the TI processor family.
Change-Id: I0c3db97950dfa832f1f1918fc10c180f068bba74
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The stm32 family supports using SYSRESETREQ as a software reset, lets
use it.
Change-Id: I171ffa8d888a2d0c28b266051030311521e9bca9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/472
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This sets the default stellaris working area to 2k rather than
the current 8k. 2K is the smallest RAM size in the stellaris family.
Change-Id: I1407f758eb0926cc094b824a6d25199b313c45de
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/458
Tested-by: jenkins
Added the file imx28.cfg to the target directory
Added the file imx28evk.cfg to the board directory
Change-Id: I02a74a03f3773892f830d13660ffdded34f3261d
Signed-off-by: James Robinson <jmr13031@gmail.com>
Reviewed-on: http://openocd.zylin.com/428
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32L ref manual (RM00038 Rev5) states the SW-DP id should be 0x4ba00477.
The correct value from silicon is 0x2ba01477 - the typo has been confirmed by ST.
Change-Id: Ie35a1f13dc5dedc1b148fb219c6974bfa48b537c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/441
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This enables the user to override the transport used for st-link.
If JTAG is selected it will also change the default id used to the JTAG id
rather than the SW-DP id.
Change-Id: I4fe352e4932e2f4ec278168e99ba2d2d50fd850a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/443
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Make _TARGETNAME variable global so it could be used by scripts sourcing it.
Change-Id: Iaf1c3b53875734658b1b8f136c9bb958988b56bf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/421
Tested-by: jenkins
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This patch add jtag support to the stlink driver add
two new transport types, JTAG and SWIM.
Change-Id: I7089d74250330be5c6a01c24066307641df7d11e
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/393
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Yegor Yefremov
Andrey Smirnov
Seth LaForge
Lee Bowyer
Paul Fertser
Tim Sander
Felipe Balbi
Spencer Oliver
Jörg Wunsch
Tim Kryger
Andrey Yurovsky
Fatih Aşıcı
Adrian Burns
Robert P. J. Day
Alex Murray
Sergey A. Borshch
Nemui Trinomius
Sergio Chico
Greg Ungerer
Franck Jullien
Brad Riensche
Marek Vasut
Giuseppe Barba
Hsiangkai Wang
Andreas Fritiofson
Ben Nahill
Peter Dietzsch
Salvador Arroyo
Vladimir Zapolskiy
Mathias K
Johan Almquist
Roman D
is2t
Gianluca Renzi
Vandra Akos
Olivier Schonken
David Anders
Jim Norris
Neil Jensen
Jonathan Dumaresq
James Robinson
Freddie Chopin
Michel JAOUEN
John