Read buffer is sized for 32-bit APB version of PWRSTAT/PWRCTL registers. Initialize to zero so 8-bit JTAG register mirrors are accurate.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I81310649fa7180893d0188aab3c8a14315aaea0a
Reviewed-on: https://review.openocd.org/c/openocd/+/7183
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I2b6a8365f554e332520fa77ccf076188083a932f
Reviewed-on: https://review.openocd.org/c/openocd/+/7122
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
New GCC reports 5 warning:
src/jtag/drivers/ep93xx.c: In function 'set_gonk_mode':
src/jtag/drivers/ep93xx.c:123:47: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
123 | devicecfg = *((volatile int *)(syscon + 0x80));
| ^
src/jtag/drivers/ep93xx.c:124:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
124 | *((volatile int *)(syscon + 0xc0)) = 0xaa;
| ^
src/jtag/drivers/ep93xx.c:125:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
125 | *((volatile int *)(syscon + 0x80)) = devicecfg | 0x08000000;
| ^
src/jtag/drivers/ep93xx.c: In function 'ep93xx_init':
src/jtag/drivers/ep93xx.c:182:46: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
182 | gpio_data_register = gpio_controller + 0x08;
| ^
src/jtag/drivers/ep93xx.c:183:56: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
183 | gpio_data_direction_register = gpio_controller + 0x18;
| ^
Change pointer type to allow pointer arithmetic.
Change-Id: Idd78a7156bdf99df2624043e924b8e54a0588ace
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7180
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change") replaces the jimtcl command "expr" with an openocd
version that detects the TCL syntax change and prints a warning.
The openocd "expr" command will be dropped after v0.12.0,
One side effect is that openocd invokes polling the target after
every openocd command, causing scripts that use several "expr"
commands to run much slower; see [1].
The proper fix would require openocd to invoke polling only at the
time period deadline, instead of at each command. Such fix is too
risky to be applied now, due to short time before v0.12.0-rc1.
As a temporarily workaround, let openocd to detect the "expr"
command and skip the polling.
This will be dropped together with the openocd "expr" command.
Change-Id: I8151aa28694817001046165a15475d64896f985e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/362/ [1]
Fixes: c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr' syntax change")
Reviewed-on: https://review.openocd.org/c/openocd/+/7174
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not used outside the file should not be exported
and should be declared as static.
Change-Id: Icbe7f7bce287b903edec9dc9db3370722c51fbd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7173
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Variables should not be declared in the include file, otherwise
multiple include will cause multiple instances.
Move the declaration in the C file and make it static.
Change-Id: I8b4884cba643a792a78df4e123aa324b19d92279
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7172
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Move the existing comments to the static declarations.
Change-Id: Idf208e3fda4b3f8df789553cf03ebf5f20d811bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7170
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I6a059080bbba9b3559d26c641b217be8be3b199e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7169
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I2475524f4c14520e3163572560f4a9f276356ed5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7168
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not exported should be declared as static.
Change-Id: Ieb627f7f896e4663b0d5b18c4ab1853b39d23d03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7167
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: Ie3bd17535c8cb2a0fec5d3bedfe7de3e0a702613
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7166
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Symbols that are not exported should be declared as static.
Change-Id: I6224ae89ebda3230dfee2413e3823be9b8716bba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7165
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The function set_log_output() has never been used after the drop
of eCos build with commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") in 2012.
Drop it!
Change-Id: I070b688061776c7ced5db18f738d78a4a7623726
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7164
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For some configurations, notably on DAP systems, resolve issue where single-stepping does not always transition into the HALTED state.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I053f4eaffad8c3228878ba87580ada640e4bd2fe
Reviewed-on: https://review.openocd.org/c/openocd/+/7150
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Enable ADIv5 DAP systems via JTAG or SWD transport
- Select correct PWRCTL/PWRSTAT bits for XDM/APB
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I5894210c804f85075da868d0cfc6fb20b589d99f
Reviewed-on: https://review.openocd.org/c/openocd/+/7144
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We have left the camelcase symbols *xPSR* for some time, to avoid
any conflict with possibly pending patches in gerrit.
With the approaching v0.12.0-rc1, it's time to revisit it.
The patches in gerrit that conflict with this rename are all not
merge-able due to conflicts or due to negative review.
Drop these CamelCase symbols.
Change-Id: Ifbac4c1df9cc55994e024971a2aaebeed2ea4ed3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the help of checkpatch, some CamelCase symbol passed
through the filter of maintainer's review.
Drop them.
Change-Id: If5fb07b2ffb89e853dd2a61f20d4134aa6e20d24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 48f267d4ad ("flash/stm32l4x: avoid using magic numbers for device ids")
Fixes: 5ab74bde06 ("semihosting: User defined operation, Tcl command exec on host")
Reviewed-on: https://review.openocd.org/c/openocd/+/7154
Tested-by: jenkins
Use indirect enum IDs to access XDM registers in preparation for supporting both NAR (JTAG) and APB (DAP). No new clang static analysis warnings.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I0b742fe4661ff3cf609454b8650493d141a1e1ff
Reviewed-on: https://review.openocd.org/c/openocd/+/7143
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As a follow-up of talks between JEDEC and STMicroelectronics,
JEDEC agrees to let OpenOCD project including the manufacturer's
identification code list extracted from JEDEC JEP106 document and
to let OpenOCD being updated regularly using the future JEDEC
JEP106 document versions. JEDEC requires OpenOCD to report the
origin of the JEDEC JEP106 manufacturer's identification code list
together with the JEDEC copyright.
As agreed with JEDEC, add in the file jep106.inc:
- the SPDX tag with the GPL license of the OpenOCD project;
- the JEDEC copyright;
- the text provided by JEDEC reporting the origin of the JEDEC
JEP106 manufacturer's identification code list.
While there:
- add a line reporting the version of the JEP106 document that was
used for the current code list extraction;
- remove the obsolete comment, as the script for extraction is not
working anymore; keep the script as example.
Change-Id: Iaa76716db14e15ffca04fcf7d8c27bb85a27ba10
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The full text of the license is already available in the file
LICENSES/preferred/BSD-2-Clause
and there is no need to replicate it in the source code.
Remove the BSD-2-Clause boilerplate but, preserved the copyright
notice because it provides the info on the copyright holder.
Change-Id: I162aa4ad06b551f1a71a28d049cb797ee8ab5a01
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7146
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
In the app-trace module we are polling the target in the while loops
outside of the server.c
In that loops, we need to catch ctrl+c signal by checking shutdown_openocd
status
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Id87c709a01470bf6d3642078b160a68ca85f4406
Reviewed-on: https://review.openocd.org/c/openocd/+/7142
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested with an PLUS-F5270 board which uses the MM32F5277E9PV.
Signed-off-by: iysheng <iyysheng@gmail.com>
Change-Id: Icb75ae8337fdc6fa60e39d3d74dd8bc163707bdd
Reviewed-on: https://review.openocd.org/c/openocd/+/7136
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
kinetis.c:994:61: error: '%u' directive output may be truncated
writing between 1 and 10 bytes into a region of size 4
[-Werror=format-truncation=]
tested with scan-build-14
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I72d141a3f8e19ca3596beee2be8434fc8492946f
Reviewed-on: https://review.openocd.org/c/openocd/+/7140
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Scan-build of target/xtensa/ has no clang analyzer warnings from xtensa source files.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I11a125c923ece9a6fd0d9ee1698f742f88ee5cab
Reviewed-on: https://review.openocd.org/c/openocd/+/7141
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it rename misleading write_algorithm_sp to write_algorithm_stack
and change messages referring 'stack pointer' instead of stack.
No functional change.
Change-Id: Ibb9897d3f01734812ed0f8bc8cd43b935a573f8a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7132
Tested-by: jenkins
Reviewed-by: Salvatore Giorgio Pecorino <salvatore-giorgio.pecorino@st.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
FLASH_MAX_ERROR_STR is not used since commit 815c3b3533
(merged in ~2008)
Change-Id: Ic117a2e3d22235c31dc14533b6564ebf5a13ae58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7121
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The value of struct flash_driver::command can be NULL when the
flash driver does not need to add any new command.
Remove empty command definitions.
Change-Id: I5413967d4069030234469822d24e9825425ae012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7120
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The change 6363: Call poll at a fixed interval
switched from target_call_timer_callbacks() to target_call_timer_callbacks_now().
It breaks the timing as all timers callbacks are called every time
one timer expires.
Revert this part of change and use target_call_timer_callbacks().
Fixes: db16b3dc5b (Call poll at a fixed interval.)
Change-Id: Ib5b7774de9694d40c55d2a4109d0d1582fc5008b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7118
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since commit 88f429ead0
5321: target/cortex_m: faster reading of all CPU registers
debugging with a kitprog adapter freezes at debug entry.
How to replicate:
openocd -f interface/kitprog.cfg -f target/psoc4.cfg
Connect to telnet server.
Make sure the target is running:
resume
Halt the target:
halt
Without this patch OpenOCD freezes in kitprog_hid_command()
in library call hid_write().
Reduce the number of SWD transactions sent in one USB bulk write
as a workaround, simply use shorter buffer.
For details see the comment in src/jtag/drivers/kitprog.c
Change-Id: I0116894d5ebf1655f6011f0d35acdbbc178cd48c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7107
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When printing memory sizes standard ISO 80000-1 prefixes should be used.
Also a space should be added between any number and its unit according
to papers publication rules.
Change-Id: Id1d35e210766b55c201de4e80ac165d8d0414d0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix Unused code Dead assignment at line 657
Fix Memory error Double free at line 2851
Fix Memory error Memory leak at line 2530
Fix error: 'a3' may be used uninitialized at line 758
Fix error: '%04x' directive writing between 4 and 8 bytes
into a region of size 5 at line 2471
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0382a622bc7c4108a335fd741816577e79240397
Reviewed-on: https://review.openocd.org/c/openocd/+/7137
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Also used type helper (PRId64) to specify format of int64_t
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I594863eab594aff621c26fefcc69a1872e9730ee
Reviewed-on: https://review.openocd.org/c/openocd/+/7111
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some files have author info some doesn't. For the consistency we removed all.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie6f1ec012302e3a954c75c5106f12820722cb715
Reviewed-on: https://review.openocd.org/c/openocd/+/7104
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Change-Id: I9466edd2f43791e64f2dce719957c67728f3ec06
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Most adapters define their own commands to obtain the GPIO number and
other GPIO configuration information such as chip number, output drive
type, active high/low.
Define a general command 'adapter gpio' as replacement for the
driver-specific ones.
Change-Id: I1ca9ca94f0c7df5713172e9f62ffb0ad64e9ee97
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6967
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The S_RESET_ST sticky bit is reset after DHCSR read.
It is set at power-on reset and keeps active until the debuger reads DHCSR.
Ignore S_RESET_ST at the very first read after OpenOCD start
and suppress possibly misleading message "external reset detected"
if we cannot guarantee the reset happened recently.
While on it add a TODO comment.
Change-Id: I15217c2ca6f69ac97aff8be86bce67cba94a42cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7109
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide a customizable hook for handling target-specific GDB queries
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I684a259ed29f3651cbce668101cff421e522f79e
Reviewed-on: https://review.openocd.org/c/openocd/+/7082
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add additional error handling for targets where gaps may exist in reg_list[]
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I65232429e2de08f5d54eeca53aea0db8ce2b58af
Reviewed-on: https://review.openocd.org/c/openocd/+/7103
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'init' causes the execution of few lower level
commands, e.g. 'target init', and switches from command mode
COMMAND_CONFIG to COMMAND_EXEC, with an intermediate switch back
to mode COMMAND_CONFIG.
A timed target polling can occur during the execution of 'init'
and the target's status can trigger the execution of some events.
E.g. if a target has been left halted by a previous execution of
OpenOCD, the first poll will find the target halted, calling the
corresponding 'halted' event.
The event handler can use commands that can only be executed in
mode COMMAND_EXEC. If the poll happens while OpenOCD is in mode
COMMAND_CONFIG, the triggered handler will fail.
Prevent the target polling to operate during the execution of the
'init' command.
Change-Id: Ia435a5d2039be9b247e2336616dab53ed5d983ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7007
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The same flag 'jtag_poll' is currently used as local data for the
command 'poll' and to temporarily mask the target polling.
This can cause unexpected behavior if the command 'poll' is
executed while polling is temporarily masked.
Add a new flag 'jtag_poll_en' to hold the temporarily mask
condition and keep 'jtag_poll' for the 'poll' command only.
While there, change the initial assignment of 'jtag_poll' using
the proper boolean value.
Change-Id: I18dcf7c65b07aefadf046caaa2fcd2d74fa6fbae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB remote serial protocol specifies breakpoint/watchpoint packet
responses can be an empty string to indicate the specified breakpoint
type is not supported. Add support for this response alongside existing
"OK", "E NN" replies.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iaf6280e4c936eb95a92bc80cc74d451ebb328dc3
Reviewed-on: https://review.openocd.org/c/openocd/+/7102
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After a certain RTOS has been configured there is no mechanism
to go back to no RTOS support. It may be useful for debugging
purposes. With the provided modification, the "none" option
of RTOS is provided as a valid option.
It has been tested in two different board (Cortex M4 and Cortex M33).
Documentation has also been updated.
Signed-off-by: Asier Llano <allano@hubbell.com>
Change-Id: I602210bff31ccadd41c41e9454c52b5fffa1671e
Reviewed-on: https://review.openocd.org/c/openocd/+/7092
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This one doesn't have the license in there, which means now it's
acceptable to GPLv2 again.
See https://github.com/riscv/riscv-openocd/pull/711
Change-Id: I8ba27801172ffa955470d2627fa656cad282ee99
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7087
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tcl commands 'arm reg', 'arm mcr/mrc' do not work on M-profile based devices.
Isolate them from 'arm core_state' and 'arm disassemble' and do not chain
them from armv7m_command_handlers.
Change-Id: I2c6befdf82575e95cf05ed158ab5e6faa1a182c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7101
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tcl command 'arm core_state' was exposed even on Cortex-M devices.
However it returned message "Unsupported Command" without error status
on such device.
Set the only possible arm->core_state ARM_STATE_THUMB in armv7m init.
Block setting core_state to arm on Cortex-M.
Change-Id: I9525553ac8863a6cf77bbacbcd57e354b6cfe1ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7100
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If a Cortex-M MCU become unresponsive during a debug session and
re-examination fails to find MEM-AP, debug_ap pointer is set to NULL.
Eventual call of cortex_m_poll() dereferences debug_ap.
Check debug_ap validity at the begin of cortex_m_poll().
Change-Id: I9519f48760c91a48a9e5e8c34634d247098cb14a
Fixes: 35a503b08d (arm_adi_v5: add ap refcount and add get/put around ap use)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Just a cosmetic refactoring.
Change-Id: I7fbc05324e346fafc98d1b42691d33d3d8fbd04e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7003
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
AARCH64_COMMON_MAGIC was same as CORTEX_A_COMMON_MAGIC, probably copy pasta.
Define unique AARCH64_COMMON_MAGIC
Change-Id: Ie30e0028453a1fce5624ecad9bf73d5ac3791281
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6997
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Unify common_magic type to unsigned int
Move common_magic to be the first member of the struct
Add unsigned specifier to xxx_COMMON_MAGIC #defines
Change-Id: If961d33232698529514ba3720e04418baf6dc6fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6996
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The flash/nor subsystem uses bus_width and chip_width for CFI
external flash only. Drop setting these values for internal flash.
Change-Id: I64e79ab38b6e39e845ff96fbf4f60145e3b9690a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7098
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The working area allocation routines use 4 byte word alignment.
In the corner case the size of the working area is not aligned,
target_alloc_working_area() of size = target_get_working_area_avail()
will fail because the size gets aligned up and does not fit to the area
which size is aligned down.
Align down the result of target_get_working_area_avail() to cope with that
corner case.
While on it use fancy ALIGN_... macros instead of bitwise and operator.
Change-Id: Ia2a1e861c401c2c78fe6323379a3776fb4f47b06
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7096
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Kinetis 100 MHz rev 1.x devices have no SMC and hence need different
checking of the run mode. Details about the differences between rev 1.x
and 2.x of the Kinetis 100 MHz series can be found here:
https://www.nxp.com.cn/docs/en/application-note/AN4445.pdf
Signed-off-by: Martin Hierholzer <martin.hierholzer@desy.de>
Change-Id: Ib705385a931275159bdae9b31caecc6ec9c0da1e
Reviewed-on: https://review.openocd.org/c/openocd/+/7015
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Previously, if the target was halted before the FreeRTOS scheduler was
started but after at least one thread was created, then the current thread
would be set to whichever thread had the highest priority. In addition to
being misleading, because that thread is not actually running, it can
cause issues with gdb. For instance, breaking somewhere before the first
thread is created will show the current execution as the current thread,
but stepping over a line that creates a thread will cause the current
thread to switch to the newly created thread and the current execution to
disappear. The sudden disappearance of the current execution thread seems
to confuse some versions of gdb.
With this change, the value of xSchedulerRunning is checked to determine
whether the scheduler has been started. If it hasn't, then a fake
'current execution' thread is always created and made the current thread.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: Ide0fe7d9ffb9fac95cee4c805735f434c7c4934d
Reviewed-on: https://review.openocd.org/c/openocd/+/6935
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When there are no rtos threads or none are active, a fake thread with
ID 1 is created for the current execution, but the current thread ID was
never set to this new fake ID. This would lead to an incorrect attempt to
read stacked registers for this fake thread. Explicitly setting the
current thread ID to the fake ID ensures that the registers are read from
the core instead of calling freertos_get_thread_reg_list.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I694509a0e01df089429b20ff1b879fc0592b532d
Reviewed-on: https://review.openocd.org/c/openocd/+/6934
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make the main RISC-V structure more compliant with OpenOCD coding style.
Other typedefs remains as is.
Change-Id: I5657ad28fea8108fd66ab27b2dfe1c868dc5805b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6998
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
We found that the NPCX has an issue with the byte lanes so that non byte
aligned writes aren't working. To overcome this, for byte accesses we
copy the byte to be written to all of the byte lanes.
doc: Document command nu_npcx_quirks
Signed-off-by: benjbender <benjbender@gmail.com>
[Andreas Fritiofson: Squashed commits]
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I9ef63bf692f4e68f57459e1ec33f3abcbf533cd2
Reviewed-on: https://review.openocd.org/c/openocd/+/6630
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for DAP interface to Cadence vdebug driver.
It implements a new transport layer for dapdirect_swd.
Change-Id: I64b02a9e1ce91e552e07fca692879655496f88b6
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6965
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit b8e18d292e ("helper/jim-nvp: comply with coding style
[1/2]") tags as deprecated the old CamelCase API of jim-nvp, so
that old patches already in gerrit or in user's local git can
still build while dumping a deprecated message.
So far, we have not found any such case, so the deprecated API can
be safely dropped in preparation of v0.12.0-rc1.
Drop the compile flag "-Wno-error=deprecated-declarations" and the
deprecated API.
Change-Id: I52ce47eda69a51c2dd29aac15f16e285492d89b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7052
Tested-by: jenkins
With most of the files already processed through scripts, replace
manually the license to the few remaining files.
Change-Id: I3c7131e66b89ddad482f1074b5be5a9a69fdf6fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7073
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I30cd66ac7d737f1973c68fdbb841ffcf00e917c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7072
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: If0194089baded7f58dc5d87a35d6e0aff9f43785
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7070
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ie873d12bb0fb838d0d6252e6b9ca3c2118853e9a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7069
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I7851617e2682f97ccc3927e3941aadef2df63b54
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7068
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ic7db91fe37d1139d42c99e303b3243b6c8fe3ea2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7067
Tested-by: jenkins
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line in specific format.
Move the SPDX tag to the first line and fix it where needed.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ie9a05f530009d482a4116eebd147fd7e1ee3d41e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7066
Tested-by: jenkins
Use the standard SPDX tag, where it was incorrectly applied.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Iaec63abc6e0a38e5b0ae0ea7f5ecee7ca007bbbd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7065
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
Change-Id: I29f51caa5ae9854d05ce7e150d168a7002607cd1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7064
Tested-by: jenkins
Few files have the FSF boilerplate without the latest statement on
where to get the GPL license.
Manually replace the FSF boilerplate with the SPDX tag.
While there, reorganize the copyright statement.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I0c908d01c010e24f9c7e94885e7fbed4ecf26a86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7063
Tested-by: jenkins
Add the new license text in the license pool.
Replace the GPL and BSD boilerplates with the SPDX tag.
Add the copyright owner of Atmel, as it was explicitly listed in
the BSD boilerplate text.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ibb117dbf8402269be3e5ba4f4c472162494d813f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7062
Tested-by: jenkins
Add the license exception text in the license pool.
Add the exception chapter in license-rules.txt
Replace the boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ied513b7c9c0722ed2a9c11dbdff3fbf59f1b41ce
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7061
Tested-by: jenkins
Add the license text in the license pool.
Replace the BSD boilerplate with the SPDX tag.
Add the copyright owner of Jim Project, as it was explicitly
listed in the boilerplate text.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I6dd004b1945773c10539016ce733d1fbfe776a9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7060
Tested-by: jenkins
Replace the BSD boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I5a8cab2051eee7eb99adf67f9631b0827c1359de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7059
Tested-by: jenkins
Some file miss completely the license tag.
Add the SPDX tag, using the same GPL-2.0-or-later license of the
OpenOCD project.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I1fb51e722232d14f050458a820c3041de3dc9138
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7058
Tested-by: jenkins
SPDX tag is replacing the FSF boilerplate.
For files that have both, remove the FSF boilerplate and keep only
the SPDX tag.
Change-Id: I04c4764d13d4ca92453f30ed16aeae53cd4c3fc8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7057
Tested-by: jenkins
Add the SPDX tag to makefiles, configuration scripts and tcl files
present in the folders under src/
Change-Id: I1e4552aafe46ef4893d510da9d732c5f181784a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7051
Tested-by: jenkins
ARM/RISC-V semihosting calls SYS_READ/SYS_WRITE require
inversion of the result value as described in
"Semihosting for AArch32 and AArch64". Prior to
this patch, this was done correctly only if
(semihosting->is_fileio==false).
This patch has been tested with STM32F446.
Change-Id: I1b34c8d8393f7dfa66ee6539904a2eaf8f9154b0
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/232/
Reviewed-on: https://review.openocd.org/c/openocd/+/6803
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable 'smp_break' is only set and used in case of smp.
But clang cannot track if 'target->smp' get modified between the
set and the use of 'smp_break', so it consider possible to use
'smp_break' uninitialized.
Initialize 'smp_break' to silent clang.
Change-Id: Ifa25a84fe9ffa25b8b58d7920ec77994c3b7ebfe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 77287b8d47 ("target: add Espressif ESP32 basic support")
Reviewed-on: https://review.openocd.org/c/openocd/+/7050
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
These enum values are useful for the arch level semihosting call handlers.
Currently riscv uses them, we also need similar return codes for the xtensa.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I8f63749cc203c59b07862f33edf3c393cd7e33a9
Reviewed-on: https://review.openocd.org/c/openocd/+/7039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This driver is used with the ESP32 chips which has builtin USB-JTAG
interface. e.g. with ESP32-C3, ESP32-S3
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61
Reviewed-on: https://review.openocd.org/c/openocd/+/6943
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Ian Thompson
Steve Marple
Antonio Borneo
Toms Stūrmanis
Antonio Borneo
Marc Schink
Erhan Kurubas
iysheng
Tim Newsome
Tomas Vanek
Paul Fertser
MadSquirrel
Asier Llano
Martin Hierholzer
Frank Dischner
Ben Bender
Jacek Wuwer
Pavel Kirienko