you can now set a variable in a script like set version [version].
Also version takes an optional argument "git" to show git version
of source. If git is not installed during the build, then this
will yield an error that is ignored during the build and "version git"
returns an empty string.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Commands that output progress output and no return value
will have the progress output captured.
Commands that do not output progress output(tcl commands)
will return the tcl return value instead.
The advantage here is that it is no longer necessary to
consider which command one is capturing, it works for
either.
Example #1: capture progress output:
set foo [capture help]
Example #2: capture tcl return value
set foo [capture {set abc def}]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
for non_cfi cfi chips free() was invoked on rodata.
The mystery is why this bug has survived for so long.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
sizeof() is a bit less scary than seing assumption
about size of type, no bug as such.
Use NULL instead of 0 for pointers. More obvious that
it is a pointer from code inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
This simple patch fixes a problem I noticed on the xscale where incorrect values
are sometimes reported by the reg command. The problem can occur when
requesting the value of registers in the xscale-specific register cache. With a
couple of exceptions, none of the registers in the xscale register cache are
automatically retrieved on debug entry. This is probably fine, as they are
unlikely to be needed on a regular basis during a typical debug session, and
they can be retrieved when explicitly requested by name using the reg command.
The problem is that once this is done, the register remains marked as valid for
the remainder of the OpenOCD session, and the reg command will henceforth always
report the same value because it is obtained from the cache and is never again
retrieved from the debug handler on the target.
The fix is to mark all registers in the xscale register cache as invalid on
debug entry (before the two exceptions are retrieved), thus forcing retrieval
(when requested) from the target across resumptions in execution, and avoiding
the reporting of stale values.
Small addition change by Øyvind: change 'i' to unsigned to fix compiler
warning for xscale_debug_entry() fn.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I a mail conversation with Øyvind we stated that speed may not be set at
all on case CLOCK_MODE_KHZ and CLOCK_MODE_RCLK. Also there isn't proper
error propagation adapter_khz_to_speed or jtag_rclk_to_speed.
So jtag_get_speed may need some rewrite for error propagation.
CC: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Do not fail startup if communication with target is
not possible.
OpenOCD supports launching without a target connected
or the target powered down.
The user will typically power up the target and issue
a "reset init" + load his application after OpenOCD
is started then.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
This new cmd adds the ability to choose the Cortex-M3
reset method used.
It defaults to using SRST for reset if available otherwise
it falls back to using NVIC VECTRESET. This is known to work
on all cores.
Move any luminary specific reset handling to the stellaris cfg file.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
bitq.c: In function ‘bitq_scan_field’:
bitq.c:224: error: declaration of ‘pause’ shadows a global declaration
/usr/include/unistd.h:429: error: shadowed declaration is here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
committed so as to ease cooperation and to let it be improved
over time.
So far it supports:
- halt/resume
- registers inspection
- memory inspection/modification
I'm still getting up to speed with OpenOCD internals and AVR32 so code is a little
bit messy and I'd appreciate any feedback.
if a tap could not be _enabled_, the error message was
'failed to disable tap'. Fixed that. Also, display the failing
tap's name.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
The patch improves flash erase for STR9x in case of a full bank erase.
Then the chip erase command is used instead which improves speed significantly.
Also I think it might help if e.g. STR912 enters some state where flash banks are locked, and a chip erase command is the key for unlocking the flash.
ocd_ prefix is used internally in OpenOCD as a kludge more
or less to deal with the two kinds of commands that OpenOCD
has.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
if polling is off, then "reset run + halt" would fail
since halt incorrectly assumed the target was in the
reset state as it is the internal poll implementation
that moves the sw tracking of the target state out
of the reset state.
To reproduce:
> reset run; halt
JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1)
BUG: arm7/9 does not support halt during reset. This is handled in arm7_9_assert_reset()
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
back-off algorithm for polling. Double polling
interval up to 5000ms when it fails.
when polling succeeds, reset backoff.
This avoids flooding logs(as much) when working
with conditions where the target polling will fail.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It is useful to know that the printed errors are *all* the
errors there were.
Added missing error handling(found by inspection).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
it can be useful to throttle performance: test
differences in behavior, test performance effect
of long roundtrips.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This flash driver works on more than just two chips.
(Though it does need work still, e.g. to protect more than 64K.
(On non-'3748-A0 chips where errata allow that.))
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make it scriptable, so code can be conditionalized based on
what transport is in use for the session.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For the above targets the exit_point is
optional when used with run_algorithm, so remove it.
This makes updating the algorithm less error prone.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the mips32 uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the armv7m uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm4_5 codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Update the arm_checksum_memory and arm_blank_check_memory
algorithms to use a breakpoint instruction on v5 arch.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Set up more of the Luminary-specific signals, and stop cloning
a few of the JTAG defaults. More comments too.
Still leaves the "dap info 0" bugs unresolved (presumably coupled
to this particular adapter family) where TPIU, ITM, DWT, and other
debug modules wrongly display as extra NVICs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Provide $defines for more of the signals involved in the
Luminary ICDI hardware, and comment some of what's going on.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use addition for offsetting, not masking. Shorten some lines.
Make "component_start" print-only (unused otherwise; don't save).
Still doesn't resolve the issue where multiple components
are wrongly displaying as NVICs on some Cortex-M3 parts because
many PIDs appear to be zeroes ... maybe adapter related??
Signed-off-by: David Brownell <db@helium.(none)>
waiting for ZY1000 fifo to idle is now queued as
an asynchronous command. This radically improves
performance when waitIdle() is interspersed with
writes as no readback is required over TCP/IP.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Mask the upper bits after 32-bit reads.
Alsoo revert the ugly changes to use PRIx32; just cast to unsized
integers when printing (two chars not eight).
Signed-off-by: David Brownell <db@helium.(none)>
This reverts the incorrect change made to the arm9 cmd group in commit
d1eca9a74c.
The code now matches the docs and the release notes.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Bugfix and simplify legacy jtag-only defaulting
* Make "dummy" declare its jtag-only nature
* likewise update ft2232
* warn if selection is _required_ (multi-transport adapters),
fixes the "only ft2232 works" bug for at least dummy, with
other drivers going the "legacy" path (submit patches).
Signed-off-by: David Brownell <db@helium.(none)>
String compare against addresses in range 0 or so due
to not checking if there was an active session first.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Classic manifestation of weakness of dangling {
formatting :-) Hard to spot these sort of mistakes visually.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Commit 93f2afa45f dropped the sentinel off the end
of the command_registrants[] array. The loop immediately
following the initialization will walk right off the end.
Signed-off-by: Stacey Sheldon <stac@solidgoldbomb.org>
This adds the guts of a transport framework with initialization,
which should work with current JTAG-only configurations (tested
with FT2232).
Each debug adapter can declare the transports it supports, and
exactly one transport is initialized. (with its commands) in
any given OpenOCD session.
* Define a new "struct transport with init hooks and a few
"transport" subcommands to support it:
"list" ... list the transports configured (just "jtag" for now)
"select" ... makes the debug session use that transport
"init" ... initializes the selected transport (internal)
* "interface_transports" ... declares transports the current interface
can support. (Some will do this from C code instead, when there are
no hardware versioning (or other) issues to prevent it.
Plus some FT2232 tweaks, including a few to streamline upcoming
support for an SWD transport (initially for Luminary adapters).
Eventually src/jtag should probably become src/transport, moving
jtag-specific stuff to transport/jtag.
Signed-off-by: David Brownell <db@helium.(none)>
Revert change made in commit dd88b461da.
Caused segfaults when using ftdi driver under win32.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The code did not transfer the last word in no-ack transfers.
The strange thing is that this did not lead to any
observable errors.
This gaffe was introduced in commit 1f5883ea56
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Review allocation of error numbers in openocd
to avoid overlap.
Put brackets around negative numbers to avoid
issues during macro expansion.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory read/writes to virtual memory, requires that the CPU is
halted.
Use 'phys' option to write to memory while target is running.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when locking the debug access fails on the first try, it's a
bit noisy, so print out message that it succeeded on second try.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Øyvind Harboe
Mike Dunn
Alexander Stein
Wookey
Spencer Oliver
David Brownell
Oleksandr Tymoshenko
Catalin Patulea
Piotr Esden-Tempski
Thomas Koeller
Fredrik Hederstierna
Michal Demin
sb-sf
Stacey Sheldon
Marc Pignat
Olaf Lüke
Antonio Borneo
Edgar Grimberg