Various fixes for memory leaks, adds a target cleanup for aarch64
and ARM CTI objects.
Change-Id: I2267f0894df655fdf73d70c11ed03df0b8f8d07d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4478
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
includes target configuration for i.MX8M SoC family,
board file needs to set up CHIPNAME and CHIPCORES
to match the actual hardware configuration
Change-Id: Ieb6d89cab2477a58f85d0ef9cd242710950191c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4434
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
configuration also contains a reset-init procedure that disables the
watchdog and initilizes the boards DDR memory so that you can upload
baremetal (e.g. boot loader) code into DDR and start it from there.
Change-Id: I4d2311b3708a5fcb5174a3447f34ae3904de7243
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Microchip (former Atmel) SAM drivers allocate a struct per chip.
at91sam3, at91sam34:
Deallocate all chip structs from the list at once, on the first bank
deallocation.
at91samd and at91sam4l drivers do not handle more than one bank.
Convert them to simple driver_priv allocation and use
default_flash_free_driver_priv().
Change-Id: I49d7200f38a4568c7e12f306c27d1b1b72646736
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4416
Tested-by: jenkins
Most of flash drivers have to ensure proper flash write block alignment
and padding. As there was no support for it in the flash infrastructure,
each driver does it its own way. Sometimes this part of code is not properly
tested and contains bugs.
flash_write(_unlock) joins all image sections targeted to one flash bank
using padded areas as a glue. This solves alignment problems on section
boundaries but imposes other problems.
Introduce new flash bank parameters write_start_alignment,
write_end_alignment and minimal_write_gap.
New flash drivers can just properly set these values instead of handling
alignment by its own.
Adapt infrastructure (namely flash_write_unlock(), handle_flash_fill_command()
and handle_flash_write_bank_command()) to prepare write data padded
to an alignment required by the flash bank.
Rework flash_write_unlock() to discontinue write block when the gap
between sections is bigger than minimum specified in minimal_write_gap.
minimal_write_gap is set to one sector by default.
Change-Id: I4368dd402dfaf51c193bcbf1332cffff092b239b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4399
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.
The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).
Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.
default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.
Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Add configuration for the Renesas R-Car R8A7791 M2W target.
This is an SoC with two Cortex A15 ARMv7a cores, both cores
are supported.
This patch is based on initial submission by Adam Bass and
improvements by Niklas Söderlund.
Change-Id: I297da62b9ce71ad222a401d98e6bcb8502427673
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Adam Bass <adam.bass@renesas.com>
Cc: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-on: http://openocd.zylin.com/4485
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This also fixes the transport_is_hla FIXME.
Change-Id: I33960f373f11e3e203f9aed9c6d02bf7ca48ac97
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4473
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use sector sizes instead of bank size.
Detect a gap between sectors and emit xml blocks accordingly.
Detect sector overflow over the bank size.
Change-Id: If0e0e44b0c3b93067b4d717c9c7b07c08582e57b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4436
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Structures rtos_standard_Cortex_M4F_stacking and
rtos_standard_Cortex_M4F_FPU_stacking in rtos_standard_stackings.c
where using rtos_standard_Cortex_M3_stack_align for the stack-align
function. This function calls rtos_Cortex_M_stack_align with
XPSR_OFFSET = 0x3c. This offset is correct for cortex-M3 but not for
cortex-M4F and cortex-M4F with fpu. This patch adds stack_align
functions for M4F an M4F_FPU
Change-Id: If6a90b1898fccbb85619a10f3aef5277dd88ce47
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Reviewed-on: http://openocd.zylin.com/4037
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
On SMP targets, the "target smp" command creates a list of targets
that belong to the SMP cluster. Free this list when a target gets
destroyed on shutdown. For simplicity, the complete list is free'd as
soon as the first target of the SMP cluster is destroyed instead of
individually removing targets from the list.
Change-Id: Ie217ae1efb2e819c288ff3b1155aeaf0a19b06be
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
apcsw command was limited to SPROT bit only.
Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7
Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.
Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
It's not implemented for 0.11 because we don't need it. Returning error
caused 0.11 targets to not be debuggable since change
848062d0d1.
Change-Id: I8b04a1fcf3c3e8bf8340cbf39aaf475d2a213519
Tell git to give us 20 lines of context, which hopefully is enough to
deal with some spurious warnings.
Change-Id: I97cb572f7b89ff305f46290d20ed0b4674af1f5b
* Enforce OpenOCD style guide.
Change-Id: I579a9f54ed22a774bf52f6aa5bc13bcbd2e82cd8
* Fail if `git diff` fails
Change-Id: I57256b0a24247f6123cb0e25a89c1b59867cb3f9
* Maybe every line gets its own shell?
Change-Id: I1a6f83e9f3d7cfd39f8933f0dba13c3cf76f71f6
* Maybe this will error properly.
Change-Id: I50803cfc229e61158569fb6b609195f7191ecac9
* Take different approach than merge-base
Change-Id: I345cbc4eecc4755c7127e8e36e403f7b727010b1
* Fix style issues.
Change-Id: I90e71f710858524812d0ab160b25c486b7b099e7
Instead of trying to predict exactly how many steps will be required
(doable but error-prone), just allocate more memory when we need it.
Tested against HiFive1, and Arty board image.
Change-Id: I3cd9798432e65176616c700ba122daf7a5ed6209
This saves us from re-reading s0 before doing just about anything
program buffer related.
Improves DebugBreakpoint from 3.01s to 2.89s. Feels like the improvement
should be larger than that. Maybe my metric isn't very good.
Change-Id: I85e1a1ddbf09006d76c451a32048be7b773dcfe9
Add option "nvmuserrow" to "at91samd" for changing and reading the register at 0x804000 which represents various fuses.
Change-Id: I6382cc4ac15e6b9681e2f30b0ae60397a6289c3b
Signed-off-by: Stefan Arnold <sarnold@sh-sw.de>
Reviewed-on: http://openocd.zylin.com/4260
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
HWID originally added in commit 7829f31a6d
was accidentally omited during refactoring in commit
52885d2b53
While on it move old ingeneering sample of 51822 to block of 51822 rev 1
Change-Id: Ie9f15563792a27a72e71df6edbcc6b04490370ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4437
Tested-by: jenkins
KitProg firmware does not send a zero length packet at the end of the bulk-in
transmission of a length divisible by a bulk packet size. This is inconsistent
with the USB specification and results in jtag_libusb_bulk_read()
waits forever when a transmission of specific size is received.
Limit bulk read size to expected number of bytes for problematic tranfer sizes.
Use 1 second timeout as the last resort.
Change-Id: Ice80306424afd76e9fbc6851911ffd5109c84501
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4426
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Avoid ever overflowing the DWT_COMPARATOR array by allocating space for
16 comparators (the field is masked by 0xf).
On a stm32f767zi chip (on a nucleo-767zi board) I've been seeing crashes
with address sanitizer enabled due to its (apparent) 10 present
comparators. This appears to be due to
https://sourceforge.net/p/openocd/tickets/178/.
In non-address sanitizer builds, this would likely cause some random
memory to be written to in some cases. (see above bug for observations).
Change-Id: I2b7d599eb326236dbc93f74b350c442c9a502c4b
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4458
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Matthias Welwarsky
Tomas Vanek
Niklas Söderlund
Paul Fertser
Armin van der Togt
Megan Wachs
Tim Newsome
Darius Rad
Stefan Arnold
Cody P Schafer
Michele Sardo