apcsw command was limited to SPROT bit only.
Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7
Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.
Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Command
mdw 0 0x40000000
triggers Segmentation fault on an arm.
Size parameter is a nonsence that may happen e.g. if you
mistype mdw instead of mww.
Add checking for calloc() NULL return in mdb/h/w.
Use calloc() instead of malloc() as multiplication
count * sizeof(uint32_t) overflows for size >= 0x40000000.
Change-Id: I968c944d863d1173ef932a7077d526fccb9381ae
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4349
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Functions mem_ap_read() and mem_ap_write() incremented address even
if addrinc=false. I overlooked this fact and moved mem_ap_setup_tar()
set wrong addresses in no-incr mode.
Fixed by preventing address increment in no-incr mode.
Change-Id: I512e12a6a64e30cf6bc5bf77e3d57d35cc33e058
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/4326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MEM-AP access through banked data registers MEM_AP_REG_BD0..3
does not increment TAR regardless of the current autoincrement mode.
mem_ap_read_u32() and mem_ap_write_u32() can keep the current
autoincrement mode instead of switching autoincrement off.
Change-Id: Ib7ec688d3e04f1da678363cd2819ce90e8910e58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4163
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem: If the same memory location is accessed alternatively
by MEM-AP banked data registers without autoincrement and by standard
autoincremented read/write, TAR register is not updated correctly.
How to replicate: On a Cortex-M issue
mdw 0xe000edf0
multiple times. When poll is on (poll reads the same memory location)
only the first read is correct.
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 20002640
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 00000000
No problems with poll off.
0xe000edf0: 01000000
0xe000edf0: 01000000
0xe000edf0: 01000000
mem_ap_setup_tar() writes to MEM_AP_REG_TAR if requested TAR value
changed or CSW_ADDRINC_... is currently active.
However if an autoincremented access has been issued and autoinc
switched off in CSW afterwards, TAR does not get updated.
The change introduces mem_ap_update_tar_cache() which is called
after queuing of any access to MEM_AP_REG_DRW. It simulates
TAR increment to keep tar_value in sync with MEM_AP.
Crossing tar autoincrement block boundary invalidates cached value.
mem_ap_write() and mem_ap_read() do not check tar autoincrement
block boundary, mem_ap_setup_tar() is called before each transfer instead.
dap_invalidate_cache() is introduced to ensure invalidation
of all cached values during dap_dp_init() and swd_connect()
Change-Id: I815c2283d2989cffd6ea9a4100ce2f29dc3fb7b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4162
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GCC7 with -Wall warns about possible string truncation with
snprint()-type functions with "directive output may be truncated writing
1 byte into a region of size between 0 and 9
[-Werror=format-truncation=]" + "note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 12" (or similar). Fix this by
increasing sizes of buffers.
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Ib848f2a56dd658783534158947ae1be7c0e99d45
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4175
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
GCC7 with -Wextra warns about switch-case blocks which fallthrough with
"this statement may fall through [-Werror=implicit-fallthrough=]". This
can be fixed by adding "special" comments: "/* fallthrough */".
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Iba0be791dbdd86984489b2d9a0592bb59828da1e
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4174
Tested-by: jenkins
This patch adds a Cortex-M private configuration option
that allows setting the acess point during target
creation. This circumvents situations in hybrid systems
when the correct access point can not be automatically
detected.
Change-Id: If313a5250e6e66509bb9080f3498feab7781dced
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3639
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
current loop sounds to me like 'we don't know what we do, let's do it ten times, maybe we will have luck'.
should be enough to 'ping' debug port using reading CRTL_STAT.
tested on cortex-a8, snapdragon, jetson k1, cortex-r5, cortex-r4
Change-Id: Ibc62ac1eca06c141f4fccd5de7b11350ca1f35fd
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Tested-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3193
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
A developer tool: Direct access to AP registers can be useful
for handling vendor specific AP like Freescale Kinetis MDM or Atmel SMAP.
Change-Id: Ie2c7160fc6b2e398513eb23e1e52cbb52b88d9bd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2777
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the MSP432P4xx Family TRM (SLAU356A) Figure 4-7,
0x9AF is the part number for MSP432P401xx devices.
Verified on TI MSP-EXP432P401R LaunchPad.
Change-Id: I22b57c42f2a0dc8263fab6b480cf8c169c7dc295
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3486
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This was found on multiple XMC4500:
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00001c11db
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1db, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
On multiple XMC4700 and an XMC4800 this was found instead:
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00001c11df
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1df, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
Name them "XMC4500 ROM" and "XMC4700/4800 ROM" respectively.
Change-Id: If369a6d16524004ba439b878f090a313a9f3a760
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3482
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Not documented in the Reference Manuals but found on multiple XMC1100/1202:
Valid ROM table present
Component base address 0xf0000000
Peripheral ID 0x00001c11ed
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1ed, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
Name it "XMC1000 ROM", since it didn't differ between XMC1100 and XMC1200.
Change-Id: I98a5a524c0d0836f395400fbac24fd496b2ec141
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3481
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Consistently increase the space-indentation of the .full values to
nicely align with the new "Qualcomm QDSS Component v1" .type value.
Change-Id: Icd28d8f3fc7c3afcccb9dcfe138ac57d64927d1a
Suggested-by: Freddie Chopin <freddie.chopin@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3480
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Instead of placing Atmel last, after ANY_ID, place it after ARM (it's
arm_adi_v5 despite 0x4BB) and sort it with the other vendors, i.e.
before ADI and Qualcomm. Adapt column alignment.
Drop the redundant "Atmel" comment to clarify that Analog is not Atmel.
Change-Id: Ic06785db079cf58d49815a639236636c180e5e17
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3479
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On APQ8016 was found a CoreSight component designed by
Qualcomm, according to db410c HRM [1] it has a partnumber
following this schema:
[11:8] is 0x4 meaning Qualcomm designed Coresight component in QDSS. Reads as 0x4.
[7:6] is Subsystem/core family ID (e.g. denote QDSS family or generation).
[5:4] is Subsystem/core configuration options (e.g. denote cache options, etc.).
[3:2] is Subsystem/core fuse options.
[1:0] is Subsystem/core future use field
Reads as 0x440.
[1] - https://developer.qualcomm.com/download/sd410/hardware-register-description-qualcomm-snapdragon-410.pdf
Change-Id: I9b4b41fd17c59d2f5ae35b53278d06d6087665f8
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3408
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On hi6220 'dap info' returned some unknown components from ARM.
Collected from ARM docs, mostly ROM table entries.
Typo fix for Cortex-M3 FPB.
Change-Id: I96bbf7349061937b3afc8bb8d6d1650f2609f82d
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3407
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Simplify by printing one component per call, instead of one complete ROM
Table per call. Print common information the same way for all components,
including ROM tables, because ROM tables (at least the top level) contain
useful information in their identification registers, such as the
manufacturer of the SoC.
Print component designer name using the JEP106 helper when available.
Change-Id: Ic51bccd98acfae6886243500153fbdd567be2fae
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3182
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: James Mastros <james@mastros.biz>
ADIv5 specifies that DP and AP accesses may generate a WAIT
response when the hardware is not able to complete a request for various
reasons in time before the next request is sent. Currently, the software
treats a WAIT response as a fatal error and aborts operation on the DAP.
This patch implements WAIT handling by keeping a journal of all
outstanding and completed accesses, including their response status.
At certain times (when dap_run() is called), the journal is inspected
for WAIT responses and all discarded accesses are replayed to complete
them. Special care is taken to not re-execute already successfully
completed operations.
Change-Id: I2790070388cf1ab2e8c9a042d74eb3ef776aa583
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3166
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The existing arm_adi_v5.c code decodes CoreSight peripherals based
on the part number field. However, these are specific to a
particular manufacturer (often ARM). The same part number from
two different manufacturers (distinct designer ids) should not
decode as the same CoreSight peripheral.
The Analog Devices ADSP-SC58x and ADSP-BF70x have peripherals that
overlap with existing OpenOCD decoding. The part number is the
same as existing OpenOCD decoding, but have a different JEP106 code.
Most, if not all, of the existing part number entries in
arm_adi_v5.c are probably specific to ARM. Change all entries
suspected to be designed by ARM to match only ARM's designer ID.
However, to preserve legacy behavior, existing non-ARM entries are
encoded with a wildcard so that they will behave in the same way as
the existing legacy code. It is desirable, however, to start
encoding the data with designer codes to avoid such ambiguity.
Revising the code to check both the part number and designer id
seemed to a warrant a const array lookup table instead of a
multi-tiered switch statement.
Also try to sync part identification IDs with relevant ARM docs.
Change-Id: Iac1374e4cfc6f04cebb479c0e3fa9bde527cc4a3
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
[andreas.fritiofson@gmail.com: change JEP106 to designer ID, cleanup]
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3128
Tested-by: jenkins
Remove entirely the concept of a "selected" AP that has to be maintained
between calls. All the information the DAP ops need are now provided to
each call through the AP/DAP pointer.
Consolidate the cache of the SELECT fields into one single field caching
the entire register.
Change-Id: I2e1c93ac5ee8ac38a7d680ca2c660c30093a6b87
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3165
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Move the mandatory dap_ap_select() call into the dap_queue_ap_read/write
wrapper.
This avoids the need for dap_ap_select() and the notion of a "current" AP
within target code.
Change-Id: I5cde8f3eef2c662f7458be6f3b3dd44ea693bd74
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3164
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Make dap apsel without arguments show current state instead of changing
to AP 0.
Change-Id: I75ea10e3e1b8a067f2dc417ec6691dc7ceec1af6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3163
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All AP operations should select the AP to use before calling it so
there's no point in restoring the previous value afterwards.
The explicit call to dap_ap_select() before all AP operations should be
moved into dap_queue_ap_read/write() which then would have to take the
AP as an argument instead of the DAP.
Change-Id: Icacb0c76ef2a5ac36b4d2f26b52ec01a8850286e
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3156
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All mem_ap_* functions now make sure the SELECT register is updated with
the AP number that it's operating on. This shouldn't have to be handled
explicitly.
Change-Id: Ib193d8930fabb6a25715064355f98258c9580b5d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function does two separate things, powering up the DP and setting
up a MEM-AP. But the DP needs to be powered before even searching for a
MEM-AP to initialize and targets may have multiple MEM-APs that need
initializing.
Split the function into dap_dp_init() and mem_ap_init() and change all
call sites to use the appropriate one.
Change-Id: I92f55e09754a93f3f01dd8e5aa1ffdf60c856126
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3151
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reduce use of magic numbers and add AXI type MEM-AP detection. Don't try
to call dap_rom_display on a non-existent AP.
AP identification is unique per designer, so make sure the JEDEC code
matches ARM when interpreting the AP type.
Change-Id: I8e86b7de61811382afe99bf15094ab71b43f5fdf
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3150
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change the debug_ap and memory_ap fields of the cortex_a target and
the debug_ap field of the cortex_m target to be pointers to the
struct adiv5_ap instead of AP numbers in some known DAP.
This reduces the dependency on the DAP struct in the targets and
enables MEM-AP accesses to take the relevant AP as parameter.
Change-Id: I39d7b134d78000564b7eec5bff464adf0ef89147
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3147
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This required fixing the AP ID parsing in dap_find_ap() to
match IHI0031C. The AXI type was added too.
Change-Id: I44577a7848df37586e650dce0fb57ac26f5f858c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3146
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This will make it possible to reference directly the AP used for debug
in the target instance and remove the DAP reference. This will in turn
enable getting rid of the need to select an "active" AP in the DAP (using
dap apsel).
Change-Id: I265846a427c714204f4fd3df3cdb75843686c2d0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3144
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Separate out the values from adiv5_dap that are associated with a specific AP into a new struct, so we can properly support multiple APs. Remove the DAP struct from the armv7* structs, because we can have multiple CPUs per DAP, and we shouldn't have multiple DAP structs. Tidy up a few places where ap_current is used incorrectly.
Change-Id: I0c6ef4b49cc86b140366347aaf9b76c07cbab0a8
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2984
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Prepare to support multiple cortex-m cores on one DAP. Uses mem_ap_sel_*
functions and removes mem_ap_* functions. Adds a new debug_ap
parameter to the cortex_m (currently set to zero as in existing code).
Change-Id: I6926029d1e7bf44a42d453d1aff349bda824ba72
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2983
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is a TODO in the src/target/arm_adi_v5.h for MEM-AP registers.
Some new registers are introduced in ADIv5.2 specification.
MEM_AP_REG_MGT (0x20) // Memory Barrier Transfer register
MEM_AP_REG_TAR64 (0x08) // Bits[63:32] of Transfer Address
MEM_AP_REG_BASE64 (0xF0) // Bits[63:32] of Debug Base Address
Refer to
7.5 MEM-AP register summary in
IHI0031C: ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
Change-Id: I3bc4296a04c35f5c64f851e5865d3099922613fa
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2904
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem
dap->ap_current is register value, not field value.
it restores invalid ap when it calls dap_ap_select(dap, ap_old) later.
* assume the current ap is 1, dap->ap_current value would be (1 << 24).
ap_old = dap->ap_current; <-- ap_old = 1<<24 = 0x1000000.
...
dap_ap_select(dap, ap_old); <-- select 0x1000000, not 1.
* All AP registers accessing fail afterwards.
One of the reproducible case(s): CORE residents in AP >= 1
dap_lookup_cs_component() being used to find PE(*).
In most cases, PE would be found in AP==0, hence the problem is hidden.
When AP number is 1, dap->ap_current would have the value of 1<<24.
Anyone get the AP value with dap->ap_current and resotre it later would
select the wrong AP and all accessing later would fail.
The ARM Versatile and/or FPGA would have better chance to provide this
kind of environment that PE residents in AP>=1. As they have an 'umbrella'
system at AP0, and main system at AP>=1.
* PE: Processing Element. AKA Core. See ARM Glossary at
http://infocenter.arm.com/help/topic/com.arm.doc.aeg0014g/ABCDEFGH.html
Fix
Use dap_ap_get_select() to get ap value.
a. Retrieve current ap value by calling dap_ap_get_select();
src/flash/nor/kinetis.c
src/target/arm_adi_v5.c
b. The code is correct (dap->ap_current >> 24), but it's better to use
dap_ap_get_select() so everything could be synchronized.
src/flash/nor/sim3x.c
Change-Id: I97b5a13a3fc5506cf287e299c6c35699374de74f
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2935
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Some targets need arbitrary amount of time (usually not too long)
after reset (both sysresetreq and srst) to do initialisation, and
SWD/JTAG is not available during that. According to PSoC4 docs, the
debugger should try connecting until it succeeds.
Also ahbap_debugport_init might be necessary to perform after using
hardware srst too, so add it there (except for the targets that
support srst_nogate since they are very unlikely to need it).
Change-Id: I3598d5ff7b8e0bf3a5566a57dec4b0b2b243d297
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2601
Tested-by: jenkins
Add Cortex-A5 identification to ROM-table display, and also
to cortex_a_init_debug_access. This change is mostly cosmetic.
Change-Id: I7b1dd8755d70d45eb5f315aa1918d44a813b3cdf
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/2483
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Added Cortex-A15 support for DAP AHB-AP init code as per ADI V5 spec.
Also added changes to make the APB MEM-AP to work with A15.
Made the the cortex_a target code generic to work with A8, A9
and A15 single core or multicore implementation. Added armv7a code
for os_border calculation to work for known A8, A9 and A15
platforms based on the ARM DDI 0344H, ARM DDI 0407F, ARM DDI 0406C
ARMV7A architecture docs.
Change-Id: Ib2803ab62588bf40f1ae4b9192b619af31525a1a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1601
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
added "Single Wire Output" and "Trace Memory Controller" peripheral
IDs to dap_rom_display(), which is invoked by the "dap info" command
Change-Id: Iea3201007bb98e6376fbb50be40a4a2e031b0a03
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek
Matthias Welwarsky
Jiri Kastner
Freddie Chopin
Marc Schink
Andreas Färber
James Mastros
Andreas Fritiofson
Matthias Welwarsky
Peter Lawrence
Patrick Stewart
Alamy Liu
Paul Fertser
Uwe Bonnes
Olivier Schonken
Kamal Dasu
Spencer Oliver