We changed the actual target name quite a while ago.
This changes the actual target function names/defines to also match
this change.
Change-Id: I4f22fb107636db2279865b45350c9c776e608a75
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1626
Tested-by: jenkins
Usage:
export LIBUSB1_SRC=/path/to/libusb-1.0
export OPENOCD_CONFIG="--enable-..."
cd /work/dir
/path/to/openocd/contrib/cross-build.sh <host-triplet>
For static linking, a workaround is to
export LIBUSB1_CONFIG="--enable-static --disable-shared"
All the paths must not contain any spaces.
Feel free to comment or update this patchset with improvements.
Change-Id: Ib3b4970117f13a6140a1eddc493d324a52364519
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1531
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds example config and flash driver for russian Cortex-M3
microcontroller model.
Run-time tested on MDR32F9Q2I evaluation board; the flash driver
should be compatible with MDR32F2x (Cortex-M0) too but I lack hardware
to test.
There're no status bits at all, the datasheets specifies some delays
for flash operations instead. All being in <100us range, they're hard
to violate with JTAG, I hope. There're also no flash identification
registers so the flash size and type has to be hardcoded into the
config.
The flashing is considerably complicated because the flash is split
into pages, and each page consists of 4 interleaved non-consecutive
"sectors" (on MDR32F9 only, MDR32F2 is single-sectored), so the
fastest way is to latch the page and sector address and then write
only the part that should go into the current page and current sector.
Performance testing results with adapter_khz 1000 and the chip running
on its default HSI 8MHz oscillator:
When working area is specified, a target helper algorithm is used:
wrote 131072 bytes from file testfile.bin in 3.698427s (34.609 KiB/s)
This can theoretically be sped up by ~1.4 times if the helper
algorithm is fed some kind of "loader instructions stream" to allow
sector-by-sector writing.
Pure JTAG implementation (when target memory area is not available)
flashes all the 128k memory in 49.5s.
Flashing "info" memory region is also implemented, but due to the
overlapping memory addresses (resulting in incorrect memory map
calculations for GDB) it can't be used at the same time, so OpenOCD
needs to be started this way: -c "set IMEMORY true" -f
target/mdr32f9q2i.cfg
It also can't be read/verified because it's not memory-mapped anywhere
ever, and OpenOCD NOR framework doesn't really allow to provide a
custom handler that would be used when verifying.
Change-Id: I80c0632da686d49856fdbf9e05d908846dd44316
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1532
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add Thumb-2 code to write flash memories that don't support DQ5 polling
* Make sure default values for unlock commands are set even if there is no PRI information given by the flash
* Add a fixup to disable DQ5 polling for the SST 39VF3201C
Change-Id: Ib08cf20547d0f500d5f78241521e6b49050c3d40
Signed-off-by: IS2T development team <dev.is2t@gmail.com>
Reviewed-on: http://openocd.zylin.com/1449
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for ARMv7-M targets in arm_nandwrite and
arm_nandread.
Change-Id: Iab1d78d401f735e191c6a8519f3619035a300fae
Signed-off-by: Henrik Nilsson <henrik.nilsson@bytequest.se>
Reviewed-on: http://openocd.zylin.com/1188
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's unnecessary and prevents reusing this function to fix
option byte writes.
Also try to disable flash writing after an error.
Change-Id: Ib5a7b768a1523e6b8da1555126fef4c1e60ab083
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/479
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use loaders that have been built for cortex-m0, making them usable for both
cortex-m0 and cortex-m3 families.
Change-Id: Ifd82be87eaec2cb96464290c80800cec3630d619
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/604
Tested-by: jenkins
Fix following warning message logged by udev at start
udevd[421]: SYSFS{}= will be removed in a future udev
version, please use ATTR{}= to match the event device,
or ATTRS{}= to match a parent device, in
/etc/udev/rules.d/95-openocd.rules:81
Change-Id: I6de935c13a3327e3d718c110f97d19b9847ceca5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/552
Tested-by: jenkins
Reviewed-by: Luca Bruno
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This enable the stm32f2x flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 1048576 bytes from file stm32f4x.bin in 30.453804s (33.625 KiB/s)
after - wrote 1048576 bytes from file stm32f4x.bin in 23.679497s (43.244 KiB/s)
This also fixes a bug that was in the old flash loader.
The old loader waited while bit16 of the status reg was 0, the new
loader waits until this bit is 0 as stated in the flash spec.
Bizarrely this bug did not effect programming on any tested parts.
Change-Id: I3efc94d42cbe81283673a8f4203700638080af6e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/460
Tested-by: jenkins
This enable the Stellaris flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 65536 bytes from file test.bin in 5.486040s (11.666 KiB/s)
after - wrote 65536 bytes from file test.bin in 2.274001s (28.144 KiB/s)
Change-Id: I9004c9aadffa1ae3b0cbf908e6549b5b1f794508
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/403
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Correct the offset to the read pointer when clearing it on error.
Also restrict the instruction set to armv6-m so the flash driver can be
used on Cortex-M0 parts with the same flash controller.
Change-Id: I380f9dabcc41fb6e4d43a7e02f355e2381913f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/399
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This corrects permissions on the FTDI chip on the xds100v2 debugger
enabling normal users to access it.
Change-Id: I0f6618692ebdee6284eee28f9e612e68782c4d78
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-on: http://openocd.zylin.com/188
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add support for checking target against the device CLASS rather
then just the PARTNO.
This change also adds the new LM4F family (Blizzard).
Change-Id: Ia9d1e33f1f1c2817c0039a2232ecf932fae072f9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/161
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Let the target algorithm be running in the background and buffer data
continuously through a FIFO. This reduces or removes the effect of latency
because only a very small number of queue executions needs to be done per
buffer fill. Previously, the many repeated target state changes, register
accesses (really inefficient) and algorithm uploads caused the flash
programming to be latency bound in many cases. Now it should scale better
with increased throughput.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Most serial adaptors are identified by udev with SUBSYSTEM=tty and
without DEVTYPE. This patch fix udev rules to work with any listed
tty-based adaptor. It has been tested with a FTDI-based Bus Pirate.
Signed-off-by: Luca Bruno <lucab@debian.org>
Added a Perl script to contrib that uses the header files in StellarisWare complete Firmware Development Package provided by TI/Luminary to generate a new list of device IDs
Used Perl script and revision 6734 of TI/Luminary StellarisWare to update device IDs
This patch adds the initial dual flash bank support for devices such
as the stm32xl family.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the stm32 flash loader now uses the preprocessor change extension
so that it used by default.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Add comments to assembly flash loader for STM32. Add tiny improvement in
size of the algorithm (40 vs 48 bytes) and tiny speed improvement (~1.5%,
as time is wasted on waiting for end of operation anyway).
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
New versions of udev (148+) emit the following warnings:
udevd[425]: BUS= will be removed in a future udev version,
please use SUBSYSTEM= to match the event device, or
SUBSYSTEMS= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:1
udevd[425]: SYSFS{}= will be removed in a future udev version,
please use ATTR{}= to match the event device, or
ATTRS{}= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:4
udevd[425]: SYSFS{}= will be removed in a future udev version,
please use ATTR{}= to match the event device, or
ATTRS{}= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:7
...
See also http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=560141
[dbrownell@users.sourceforge.net: add IDs for Stellaris ICDI, Olimex Tiny-H]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Spencer Oliver
Andreas Fritiofson
Paul Fertser
IS2T
Henrik Nilsson
Roman D
George Harris
Antonio Borneo
Ulf Samuelsson
Kyle Manna
Uwe Hermann
Spencer Oliver
Eugeniy Meshcheryakov
Clément Burin des Roziers
Luca Bruno
Øyvind Harboe
Eric Wetzel
David Brownell
Jonathan Dumaresq
Michael Trensch
Freddie Chopin
Johannes Stezenbach
Yauheni Kaliuta
oharboe
zwelch
duane