Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The arm7_9_checksum_memory() and arm7_9_blank_check_memory()
routines are not actually specific to the ARM7 and ARM9 core
generations ... they can work for any core which can run
algorithms using basic ARM (not Thumb) instructions.
Rename them; move the declarations to a more generic site;
likewise move the code (and tidy it a bit in the process).
NOTE: the blank_check() method falsely returned a success
status (0) on one error path, when the algorithm failed.
Fixed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously this flag was stored in "target_type", so that for example
if there were two ARM7TDMI targets in a scan chain, both would claim
to have been examined although only the first one actually had its
examine() method called.
Move this state to where it should have been in the first place, and
hide a method that didn't need exposure ... the flag is write-once.
Provide some doxygen. The examine() method is confusing, since it
isn't separating one-time setup from the after-each-reset stuff. And
the ARM7/ARM9 version is, somewhat undesirably, not leaving the debug
state alone after reset ... probably more of an issue for trace setup
than for watchpoints and breakpoints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "remove (forward) declarations" patch goofed indentation on the
"cortexa8_target" struct; fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use target_to_armv7a() etc, replacing needless pointer traversals.
Stop using X->arch_info scheme in most ARMv7-A and Cortex-A8 code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The quit entry point was not being invoked. Just a source
of confusion at this point. XScale ran 100x reset upon
quit, but that code made no sense, wasn't commented
and never invoke.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
By enabling this bit, the processor halts when a debug event
such as breakpoint occurs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2668 b42882b7-edfa-0310-969c-e2dbd0fdcd60
With DCCR we are asking the CPU to halt, we should wait until
the CPU has halted before proceeding with the operation.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2638 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the ITR register but it will only be executed when the DSCR[13]
bit is set. The documentation is a bit weird as it classifies
the DSCR as read-only but the pseudo code is writing to it as
well. This is working on a beagleboard.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2634 b42882b7-edfa-0310-969c-e2dbd0fdcd60
instruction to be finished. This comes from the pseudo code
of the cortex a8 trm.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2632 b42882b7-edfa-0310-969c-e2dbd0fdcd60
nonfunctional cortex_a8 code with something that at least basically
works (for halt/step/resume, without MMU) even if it is incomplete.
(With tweaks from Øyvind, and cleanup from Dave.)
This code has mainly been developed and tested against R1606, it has
been built and tested against R2294 where it runs but step and resume
commands are broken due to regression (which should be fixed now).
This code is really written for OMAP3530. It doesn't identify debug
resources using generic DAP calls to scan the ROM table, or perform
topology detection. The OMAP3530 DAP exposes two memory access ports:
- Port #0 is connected to L3 interconnect (the main bus) with
passthrough to the L4 EMU bus ... so it will be used for most
memory accesses.
- Port #1 is connected to a dedicated debug bus (L4 EMU), with
access to L4 Wakeup, and holds the ROM table ... so it must
be used for most debug and control operations.
The are some defines to handle this in cortex_a8.c, which should be
replaced with more general code. Having access to another Cortex-A8
implementation would help get that right.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2609 b42882b7-edfa-0310-969c-e2dbd0fdcd60
David Brownell
Zachary T Welch
Øyvind Harboe
Yauheni Kaliuta
mlu
dbrownell
oharboe
ntfreak
zwelch