It is conceivable that there could be commands in the
queue when a speed change request comes in. Flush the
hw queue before changing speed. Not observed, found by
inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
According to OpenOCD error handling rules the error is
logged at where it occurs(same site where an exception
would have been thrown).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The very first command after init command should be "read target voltage".
This is a tweak for the Old Versaloon firmware. Without this, in most
most cases, it works. Under Ubuntu9.04, there is a chance that the USB
will fail. The problem disappears if I read target voltage first.
For the lastest Versaloon firmware, it's OK.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The LPC3180 NAND driver was crashing on some large page chips.
Fix:
- Crash and related functionality (don't memset too much OOB data)
- Some debug messages
- Command handling now works
[dbrownell@users.sourceforge.net: whitespace/linelength/message cleanup]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't just complain about an invalid ACK; say what the
value was, to help troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Until we manage breakpoints at runtime (patches not ready for 0.4)
the only way this code should touch them is to disable them at server
startup (a previous debug session may have left them active).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add doxygen and other comments for what's more or less the lowest
level JDAG-DP primitive, to access JTAG_DP_{A,D}PACC registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Teach most remaining ARM cores how to use the "reset-assert" event.
Same model as elsewhere: iff a handler is provided for that event,
use that instead of trying to assert SRST (which may be unavailable,
or inappropriate since it resets too much). Else no change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).
Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Using the erase bank command will cause a time out error. Replacing
this with the erase sector bank will provide a slower but safer and
stable method to erase the flash.
Signed-off-by: Laurentiu Cocanu <laurentiu.cocanu@zylin.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Shrink some overlong lines. Add my 2009 copyright.
Move a declaration to the beginning of its block.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Capture various bits of useful information that have come up on the
list but haven't yet gotten into the documentation:
- Watchdog timers firing during JTAG debug need attention;
- Some chips have special registers to help JTAG debug;
- Cortex-M3 stepping example with IRQs and maskisr;
- Clarifications re adaptive clocking: not all ARMs do it, and
explain it a bit better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates three aspects of debugger/exception interactions:
- Save the user's "vector_catch" setting, and restore it after reset.
Previously, it was obliterated (rather annoyingly) each time.
- Don't catch BusFault and HardFault exceptions unless the user says
to do so. Target firmware may need to handle them.
- Don't modify SHCSR to prevent escalating BusFault to HardFault.
Target firmware may expect to handle it as a HardFault.
Those simplifications fix several bugs. In one annoying case, OpenOCD
would cause the target to lock up on ome faults which triggered after
the debugger disconnected.
NOTE: a known remaining issue is that OpenOCD can still leave DEMCR
set after an otherwise-clean OpenOCD shutdown.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
DCC downloads should be enabled for any self repecting
openocd config file for arm7/9. Print out note about
it otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Allow targets to run checks post reset. Used to check
that e.g. DCC downloads have been enabled.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Added interface config file for JTAG/RS232 debug board originally
integrated to Neo 1973 and Neo FreeRunner phones.
Adapter was tested with i.MX31, S3C2410 and AT91SAM9260 processors.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Use correct tcl syntax to throw exception.
the syntax is "return -code error" not "return -error"
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
we don't need to know the build path of command.c when
reading normal user level error messages.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
flush JTAG FIFO before reset. Fixes RCLK problems observed
w/lpc2148, but really fixes a wider range of problems.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Based on notes from Tomek Cedro <tomek.cedro@gmail.com> and
Steve Franks <bahamasfranks@gmail.com>.
In the User's Guide, sort the list of operating systems reported
through Tcl with $ocd_HOSTOS ... and include FreeBSD.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The usual: expand several helptexts to be more correct and to use
full sentences; make the usage messages use the same EBNF as the
User's Guide; use function names for their addresses.
Also add a comment about that odd jtag_command_handlers_to_move[] thing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The usual: same EBNF as in the User's Guide, full sentence helptext,
function names *are* their addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Presto: add doxygen file comment.
Parport: note a couple gaps in layout config.
Both: use the uniform EBNF for usage, bugfix helptexts, use function
name as its address not "&name".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "parport_port" commands generally don't *require* a port_number;
they're of the "apply any parameter, then print result" variety. Update
the User's Guide accordingly.
Some of those commands are intended to be write-once: parport_port,
and parport_cable. Say so.
Use proper EBNF for the parport_write_on_exit parameter.
Parport address 0xc8b8 is evidently mutant. Say so in the "parport.cfg"
file, to avoid breaking anyone with that mutant config. But update the
User's Guide to include a sane example for the LP2 port.
Finally document the "presto_serial" command.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Fix some whitespace glitches, shrink a few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.
Add TODO list entry re full support for NAND/NOR bank names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Recent Apple gcc versions use __APPLE__ instead of __DARWIN__; accept
that too.
Also use #warning, not #warn; neither is standard, but most CPP versions
require it to be spelled out.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace, shrink
a few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing. Improve and correct various helptexts.
Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.
Don't use "&function"; its name is its address. Line up struct
initializers properly. Remove some blank lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update/bugfix the "hello" example; emphasize using EBNF syntax,
matching the User's Guide. Correct the Texinfo style guide to
say EBNF, not BNF.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing.
Don't use "&function"; its name is its address.
Unrelated: fix typo in one "target.c" usage message.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Øyvind Harboe
David Brownell
simon qian
richard vegh
Peter Korsgaard
Laurentiu Cocanu
Spencer Oliver
Vladimir Zapolskiy
Masaki Muranaka