This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:
1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:
The previous logic was erroneous. The delay in clock cyles from a bit
written to the jtag interface to a bit read by the jtag interface is:
* The number of BYPASSed TAPs before this (jtagspi) tap
* The length of the jtagspi data register (1)
* The number of BYPASSed TAPs before this one.
I.e. it is just the number of enabled TAPs. This also gets rid of the
configuration parameter DR_LENGTH.
3. Use marker bit to start spi transfer
If there are TAPs ahead of this one on the JTAG chain, and we are in
DR-SHIFT, there will be old bits toggled through first before the first
valid bit destined for the flash.
This delays the begin of the JTAGSPI transaction until the first high bit.
4. New jtagspi protocol
A JTAGSPI transfer now consists of:
* an arbitrary number of 0 bits (from BYPASS registers in front of the
JTAG2SPI DR)
* a marker bit (1) indicating the start of the JTAG2SPI transaction
* 32 bits (big endian) describing the length of the SPI transaction
* a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
* an arbitrary number of cycles (to shift MISO/TDO data through
subsequent BYPASS registers)
5. xilinx_bscan_spi: clean up, add ultrascale
This is tested on the following configurations:
* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E
Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* Disables the data output pin while SWD is reading, so that a simple FTDI
SWD interface can be made by connecting TCK to SWD_CLK and TDI+TDO directly
to SWDIO. Enabled by setting SWDIO_OE to 0.
Change-Id: I7d3b71cf3f4eea163cb320aff69ed95d219190bd
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Reviewed-on: http://openocd.zylin.com/2274
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
When listening on port 0, the system will assign a random open port. We
use this to run multiple OpenOCD instances against multiple simulators
as part of regression testing. This mechanism means the various test
instances don't have to coordinate to ensure they don't reuse any ports.
The required changes are minimal:
1. Don't increment the port number when it's 0.
2. Print out which port was assigned by the system.
Change-Id: I404c801fc405e9d8eb8420562c02e78d4db6242f
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4316
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
added missing instructions from latest available ejtag specification
(MD00047 v6.1 at time of writting) for trace control, fast data channel
and pcsample.
Change-Id: I30293951611265ffc2bd896f9d3ca6b310e5cac6
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3950
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Handle the Ctrl+A and Ctrl+E shortcuts which move the cursor to the
beginning and end of the command line, respectively.
Change-Id: I89fa5fd3c5edeb08a3f9320fda766f72ce9d7f64
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3415
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This duration vs sample count is _significantly_ closer to the truth
than simply declaring the value to be 100Hz.
Change-Id: Ie8d8bdf1959e1aa7cead0631cd2c86afe77d1efc
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4221
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Leverages the existing work that added profiling via DWT_PCSR.
hla_target doesn't have direct access to the mem_ap for doing a bulk
repeated read, but simply reading the DWT_PCSR register repeatedly is
still ~2 order of magnitude faster than halt/resume.
Change-Id: Ibe451aa95143694398370fdad6939cfb6191d56f
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4220
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use DWT_PCSR if present (reads nonzero); otherwise do halt-and-sample pc.
Signed-off-by: Simon Schubert <2@0x2c.org>
Change-Id: Id2dc4665e5008cc497a2e6e6493522d038d5af42
Reviewed-on: http://openocd.zylin.com/4211
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
We're using an I/O port reset by default. The only board currently
supported (Galileo) doesn't have SRST routed on the JTAG connector.
When using 'reset halt', we must rely on Reset Break because our
adapters don't have support for PREQ#/PRDY# signals.
Tested with Intel Galileo GEN2.
Change-Id: Ia406e31c156f8001717d5b6a08bd03f71de790d3
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4016
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Just some misc cleanups without any functional changes. It's just
easier to read.
Change-Id: I66bee31f297bcbdb8cc4446b774d7714fbaa7c83
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4015
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
No functional changes, cleanup only
Change-Id: I53c422be16d0a4ff157745d31362f6483093e5eb
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4014
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When testing with Intel Galileo GEN2 I have noticed a few iterations
where probemode entry took a little longer. At most I had to read
tapstatus twice. This patch uses a loop of up to 100 iterations to
wait for tapstatus to update with PM entry results.
Change-Id: I1c87d7dde715255b3fd2460d299b9493218533fc
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These symbols are only used within this C source file. They don't need
to be exposed to the outside.
Change-Id: Idb04550ecca7f12c3fdc8c6447eeeb871961add3
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4012
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When multiple targets are declared, it's not always obvious which
target the connection was made for, this can lead to very confusing
errors.
Reported by zjason on IRC.
Change-Id: I52906320394e89cb6cfe82054a3f94b27c999689
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4135
Tested-by: jenkins
This should allow to process any path names excluding those that have
curly braces.
Change-Id: I87bf9ddede11e2b28d5826878eb1338143f73c03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4083
Tested-by: jenkins
This doesn't seem to make any sense.
Change-Id: I272de0ea3c0e86cc9a798cbd864050aaa597c3f0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3933
Tested-by: jenkins
Reported by thesourcerer on IRC.
Change-Id: I36d4d95de176a19fdd0bf80d8b419be6ca637e98
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3893
Tested-by: jenkins
Leaving mode before closing added
Resolved a collision with JTAG API v1 error/status
checking overwriting SWIM status bytes
Change-Id: I35444ec0e6caace3e072c60085059602f4cdf0a4
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/4265
Tested-by: jenkins
Reviewed-by: Philipp Klaus Krause
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fixed a bug in stlink_usb_read_mem/write_mem preventing large data transfers
The SWIM support in stlink_usb was basically non existent so I have
implemented the missing parts. The bCBWCBLength and dCBWDataTransferLength
for STLINK-V1 protocol was not correct so that was fixed. The reason for
adding SWIM support is to add STM8 support for OpenOCD.
I have tested the driver on:
STM8 discovery board with the built-in STLINK-V1
STM8 discovery board with STLINK-V2 dongle
STM32 vldiscovery board with the built-in STLINK-V1
STM32F1xxx processor with STLINK-V2 dongle
Change-Id: I4aa80a92fb0226174356adaf2f8ff949920a621f
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3952
Tested-by: jenkins
Reviewed-by: Philipp Klaus Krause
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Functions mem_ap_read() and mem_ap_write() incremented address even
if addrinc=false. I overlooked this fact and moved mem_ap_setup_tar()
set wrong addresses in no-incr mode.
Fixed by preventing address increment in no-incr mode.
Change-Id: I512e12a6a64e30cf6bc5bf77e3d57d35cc33e058
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/4326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MEM-AP access through banked data registers MEM_AP_REG_BD0..3
does not increment TAR regardless of the current autoincrement mode.
mem_ap_read_u32() and mem_ap_write_u32() can keep the current
autoincrement mode instead of switching autoincrement off.
Change-Id: Ib7ec688d3e04f1da678363cd2819ce90e8910e58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4163
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem: If the same memory location is accessed alternatively
by MEM-AP banked data registers without autoincrement and by standard
autoincremented read/write, TAR register is not updated correctly.
How to replicate: On a Cortex-M issue
mdw 0xe000edf0
multiple times. When poll is on (poll reads the same memory location)
only the first read is correct.
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 20002640
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 00000000
No problems with poll off.
0xe000edf0: 01000000
0xe000edf0: 01000000
0xe000edf0: 01000000
mem_ap_setup_tar() writes to MEM_AP_REG_TAR if requested TAR value
changed or CSW_ADDRINC_... is currently active.
However if an autoincremented access has been issued and autoinc
switched off in CSW afterwards, TAR does not get updated.
The change introduces mem_ap_update_tar_cache() which is called
after queuing of any access to MEM_AP_REG_DRW. It simulates
TAR increment to keep tar_value in sync with MEM_AP.
Crossing tar autoincrement block boundary invalidates cached value.
mem_ap_write() and mem_ap_read() do not check tar autoincrement
block boundary, mem_ap_setup_tar() is called before each transfer instead.
dap_invalidate_cache() is introduced to ensure invalidation
of all cached values during dap_dp_init() and swd_connect()
Change-Id: I815c2283d2989cffd6ea9a4100ce2f29dc3fb7b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4162
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The existing code only used Memory Access mode to read memory,
which uses 32 bit operations only.
Rework the code to check the alignment/size of the read/write operation,
and use the Memory Access mode to read aligned 32 bit memory.
When using unaligned access, or 8 or 16 bit reads, use LDR{BHW} and STR{BHW}
instead.
The exception handling is still the same as it was before (meaning it breaks
when things go wrong), but I can now read an 8 bit register correctly.
Change-Id: I739a5ee825c0226ed4a89c32895cc2a047b8dc15
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4301
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit ef02b69b14 included
a call to cmsis_dap_cmd_DAP_Connect() before calling
cmsis_dap_cmd_DAP_SWJ_Sequence(). According to comment
it is necessary for at least Keil ULINK-ME.
Commit 72c3464be4 added
a cmsis_dap_cmd_DAP_Disconnect() before connect call to pair
connection/disconnection. It solves some problems on Atmel EDBG.
Unfortunately calling either of cmsis_dap_cmd_DAP_Connect()
or cmsis_dap_cmd_DAP_Disconnect() deasserts reset signal.
So these workarounds break ability to connect under reset.
Use cmsis_dap_cmd_DAP_Disconnect() and cmsis_dap_cmd_DAP_Connect()
pair only if both SRST and TRST are deasserted.
Change-Id: I0914dae0a1360b8c7fe48231ff3867caedfb2dbe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Leonardo Sabino dos Santos <leonardo.sabino@gmail.com>
Reviewed-on: http://openocd.zylin.com/4100
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Theese devices do not have a gap in sector numbering.
The driver translates sectors numbers 12 13... to 16 17... as used on dual
bank flash devices. Therefore erase of sector 12 and above fails with error
'stm32x device protected'
on F413/423.
Drop sector number translation for devices without has_large_mem flag.
Change-Id: I65531c0dfe02e2fd0f3d68f0615e0926e9901391
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4299
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A protection block comprises two adjacent sectors in dual bank mode.
As there are 64 and 128kB sectors joined in blocks 2 and 8, block size
should be computed as a sum of sector sizes.
Change-Id: Ie915df8cf7ca232c4565d7e0c514c8933e71fdfe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4271
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Extend HLA interface to allow multiple VID/PID pairs and use it to
autodetect the connected stlink version.
Change-Id: I35cd895b2260e23cf0e8fcb1fc11a78c2b99c69b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3961
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The CMSIS-DAP used by NXP's LS1012ARDB board only supports JTAG,
and not SWD. Calling cmsis_dap_cmd_DAP_SWD_Configure returns with an
error (and doesn't actually do anything in the debugger).
Wrap the call to cmsis_dap_cmd_DAP_SWD_Configure in a check for
swd_mode, to make sure initialisation doesn't fail needlessly.
Change-Id: Id7e568cb6e36886bd7c5b3699d198a77a51c28c9
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4294
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change-Id: Ieea1b0dec88818e9e8d5c8c5d54aa8959556d77b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4275
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The SWDIO buffer has to be enabled, by setting SWDIO_OE, for data on
SWDIO to reach the target. Explicitly do this before sending the
switch sequences for JTAG-to-SWD, etc.
This makes the code insensitive to the state of SWDIO_OE specified in
ftdi_layout_init. It used to work only on adapters with a non-inverted
SWDIO_OE inited to 1, or inverted SWDIO_OE inited to 0.
Change-Id: I4b9e520ac1c7ce2a437251a05fc036bc68de718e
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4270
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The dhcsr_save variable was used to save the value of
cortex_m->dcb_dhcsr so it could be restored later. However, all writes
in between the save and the restore use mem_ap_write_atomic_u32, not
cortex_m_write_debug_halt_mask, which means cortex_m->dcb_dhcsr isn’t
changed anyway. Delete the unnecessary local.
Change-Id: I064a3134e21398e1ecfc9f1fa7efd7b020b52341
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4240
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Matthias Welwarsky
Jiri Kastner
Robert Jordens
Marc Schink
Patrick Stewart
Tim Newsome
Karl Palsson
Simon Schubert
Felipe Balbi
barthess
Paul Fertser
Ake Rehnman
Tomas Vanek
Forest Crossman
Bas Vermeulen
Alexandre Torgue
Jonas Norling
Christopher Head