Only report non-erased or unknown sectors or if bank is fully erased.
Change-Id: I94f0bc2a0d6529d1ea5f66b284cefd6a2c61fe39
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3501
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
1) wrong last bit was shifted out in the end of IRSHIFT/DRSHIFT in
jlink_execute_scan()
2) TDI buffer was not cleared in jlink_tap_init(), results in wrong
data shifted out to the TDI and "Bad value '00000000' captured
during DR or IR scan" error message.
3) sizeof(tdi_buffer) was used in memset() to clean tms buffer. It
is the same as sizeof(tms_buffer), but shoud be fixed to make source
code consistent
Change-Id: I13f26d1c3e88eefc3856fe2b8542fb0ccea6acb1
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/3394
Tested-by: jenkins
Reviewed-by: Harry Zhurov <harry.zhurov@gmail.com>
Reviewed-by: Anton Gusev
Reviewed-by: Михаил Цивинский <mtsivinsky@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Increase workareasize when it is know we have a larger device.
Change-Id: Ieaee92e7cd25cc201989f14de122349698871412
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3378
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Corrected 2 Silicon IDs that were swapped.
I've tested with a CY8C4125AXI-483 and confirmed
that the device is recognized correctly now.
Change-Id: I6fcbee33558d8feec9abf6052df3f15523379c48
Signed-off-by: George Ioakimedes <georgeioak@gmail.com>
Reviewed-on: http://openocd.zylin.com/3619
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target_run_flash_async_algorithm() ignored abort from target
(rp set to 0) when raised after all data have been written in fifo.
I could result e.g. in not reported error during flash write.
The change adds rp test after target algorithm has finished.
Change-Id: Iadd93371e4a4602737be10079479285d81ae41b2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3560
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Using the presence of the 'chSysInit' symbol for detection of
ChibiOS is dangerous because this symbol may not be available
if link-time optimisation is used.
This patch removes this reliance, so the symbols 'ch' and 'ch_debug'
are the only things required for ChibiOS detection.
If 'ch' is present but 'ch_debug' is not, an info message suggests
that Chibios might be present without its registry being enabled.
This message has been reworded a little to make it slightly more
equivocal because the chances of a false positive message are
increased.
Addresses bug #121, "ChibiOS rtos detection fails with LTO enabled".
Change-Id: I5ef224735c06446751adee010ce75be4f30f0403
Signed-off-by: Andy Pomfret <cooperised@gmail.com>
Reviewed-on: http://openocd.zylin.com/3381
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Instead of using ARM_ prefixed variables and an "arm" target,
use CROSS_COMPILE, AS, OBJCOPY. This requires to switch from ?= to =
to avoid the host assembler getting invoked.
This allows to handle kinetis_ke subdirectory like fm4 and xmc1xxx.
Change-Id: I7ea0bf119f6c4716f4d6002794004730af49eef4
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3505
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add a Makefile that orchestrates the other loader Makefiles.
It assumes that the clean target can be run without cross toolchain.
at91sam7x does not successfully build and is not really needed either,
therefore left out.
Add an exception to .gitignore for any contrib/loaders Makefile.
Change-Id: I74456b768472f3190a1721bcf41a777bb8daf973
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3504
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
PSoC4 design prevents reset halt/init with standard/low level
SWD adapter if hw reset line configured. Give user hint
to use 'reset_config none' in such case.
Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3617
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- FPU detection and FPU register support added for Cortex-M7.
There is no apparent difference between FPv4 and FPv5_SP but ...
- Autoincrement range for MEM-AP added for Cortex-M7
This patch together with #3526 replaces #3123 except for stm32f7x.cfg.
Change-Id: I5ed5392e3835674160563ff37d67622a7bf2c877
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/3531
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The IDCODE of Artix7 15T in the UG470 is wrong; Artix7 35T and 15T don't have the same IDCODE.
I've tested this on real hardware.
Change-Id: Iac267dc449c23454dd119126749dbeb8267c18ac
Signed-off-by: Felix Held <felix-openocd@felixheld.de>
Reviewed-on: http://openocd.zylin.com/3633
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
If WAIT recovery fails (times out), an ABORT command is issued to the
DAP but under some conditions the SSTICKYORUN bit in CTRL/STAT is not
cleared as well, which renders the DP unusable. This happens when
trying to access e.g. the ROM table of powered-down cores, on many
targets.
Change-Id: Id0a7ba6180069eee562871314f520f938df9718f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3476
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Allow using physical addresses with mem2array and array2mem. In order
to minimize the impact on existing scripts, "phys" is added as an
optional 5th parameter to both commands.
This patch also adds "phys" variants to the memwrite/memread commands
in memory.tcl.
Change-Id: Ia6307f9d861789e7f3ccf1f98961d666bf8d85d6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3387
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Sometimes it is necessary to resume into a different state (ARM/Thumb)
than at debug state entry. According to the documentation this should
be possible with "arm core_state arm|thumb" before the resume command,
however the original code also restores the original CPSR, which
overrides whatever state the core was set to. This seems to work on some
cores (e.g. Cortex-A5) but not on others (e.g. Cortex-A9). Using the "BX"
instruction to set resume PC and core state works on Cortex-A9 and
ARM11, but is not sufficient on Cortex-A5, where an explicit write to
the PC (MOV pc, r0) is required additionally.
Change-Id: Ic03153b4b250fbb8cf6c75f8e329fb34829aa35f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3386
Tested-by: jenkins
Reviewed-by: Alexander Stein <alexanders83@web.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
1986VE1T and 1986VE3T have issue with flash acceleration engine described
in their errata (issue 0007).
After programming flash acceleration engine's buffer contains old data,
and therefore first read data are wrong. Because of this verification after
programming fails always. Recommended workaround for the issue is to flush
flash accelerator's buffer. To do so it's necessary to read at least 64
bytes of flash through accelerator.
Reading bytes through JTAG using default_flash_read doesn't help.
It seems that reading should be done by uC itself.
Change-Id: I18ef464a68ad5c5b16d3933f31ca61f8e2e7cca3
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/3509
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
First, fix the timeval_ms() implementation to not have K&R but ANSI
argument semantics by adding a missing void.
timeval_ms() returns an int64_t, not uint64_t or long long. Consistently
use int64_t for variables and PRI*64 as format string.
While at it, change a few related variables to bool for clarity.
Note that timeval_ms() may return a negative error code, but not a
single caller checks for that.
Change-Id: I27cf83e75b3e9a8913f6c43e98a281bea77aac13
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3499
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A developer tool: Direct access to AP registers can be useful
for handling vendor specific AP like Freescale Kinetis MDM or Atmel SMAP.
Change-Id: Ie2c7160fc6b2e398513eb23e1e52cbb52b88d9bd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2777
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
add "mrb" command to read a byte of memory into a variable
Change-Id: I5ddc9fbcc55958a249548627bd15824df6dc0d61
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3542
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Some installations of OpenOCD are used in restricted environments that
do not permit binding to public interfaces.
This patch does not affect the default behavior to listen on all
interfaces, however it does give the option to restrict services by way
of the bindto command.
Change-Id: Id51bd64b376a8c62dd47b08b4d834872925e6af2
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3534
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Today the reset option for connect_assert_srst is not done for SWD.
This patch adds this to SWD and make it possible to connect to targets which might disable JTAG interface when running.
Change-Id: Ib89f7cf59b628e8f0b5fca9dd9e362e383c4b99f
Signed-off-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-on: http://openocd.zylin.com/3018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the 'data_swap' parameter to the CFI driver, which enables
swapping of data bytes when writing/programming words to the flash.
Note, that this specifically means that bytes are not swapped when
writing command words to the flash chip. Unless you are using the SAP
in an LS102x chip to program an attached 16-bit NOR flash, you hopefully
do not need this!
Change-Id: I1e6f7169da36f373c880d1756d9c21c9957acc50
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3109
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The SAP in LS102x SoC's from Freescale is able to read and write to all
physical memory locations, independently of CPU cores and DAP.
This implementation is 100% based on reverse-engineering of JTAG
communication with an LS1021A SAP using a JTAG debugger with SAP support.
And as such, this code is for now "works-for-me", pending verification
by other OpenOCD users, or even better, actual information from Freescale
on the SAP interface.
Change-Id: Ibb30945e017894da5c402f9f633fc513bed4e68c
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3096
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv4_5_crc.inc, and convert the code to target
endianness the least intrusive way.
Change-Id: I7452b2c7e679dae14f9cda5f89bc81c16fc12cad
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3473
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Add rules to build armv4_5_erase_check.inc, and convert the code to
target endianness the least intrusive way.
Drop an unused word from the assembler sources to make the ARM bytecode
fully match that of armv4_5.c and to not break ARMv4 assumptions.
This completes the build rules for contrib/loaders/erase_check directory.
Change-Id: I36be7a944e26142088195fa3fb072d4e577bf328
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3135
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv7m_crc.inc and include it via preprocessor.
Change-Id: I4482c7acb8454de28bdf210d9f06c0720ada490a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: Ie3f95f992a98a1325428e4032a1c17346d4c9977
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3472
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: I95bb12fbe7c80b594e178468bcd4f6387c682c93
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3471
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Andreas Fritiofson says "If any adapter driver does not work with
arbitrary lengths of individual fields, it's a bug."
https://sourceforge.net/p/openocd/mailman/message/35091945/
Note also that lengths of at least 96 bits are already in use, eg. in
mips_ejtag_add_scan_96().
Change-Id: I62a150adc75c0ef78827683ca8d0a8e90310a982
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/3491
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Just like observed with the General App Kit earlier, it now started to
fail halting:
SWD IDCODE 0x2ba01477
TARGET: xmc4500.cpu - Not halted
in procedure 'reset'
in procedure 'ocd_bouncer'
SWD IDCODE 0x2ba01477
Halt timed out, wake up GDB.
Rely on the target's default sysresetreq behavior to allow flashing to
work seemlessly again.
Change-Id: Ib9ce5f2c0ab99dca6d0fc74435fe26a58437fae5
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3416
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Upstream commit
http://git.savannah.gnu.org/gitweb/?p=config.git;a=commitdiff;h=f4ebd3ed097771a729b68e688236aea665e7c1f3
makes both i386 and amd64 MSYS (and MSYS2) systems be detected as
*-pc-msys .
With this patch OpenOCD builds without any additional tweaks on MSYS2
with the latest config.guess.
Change-Id: I1ae4154f76125a84078926b425fa989904639ce0
Reported-by: "Stevens, Kelly E. M." <Kelly.Stevens@gtri.gatech.edu>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3468
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
When using SWD rather than JTAG transport, the lpcspifi driver complains:
Error: Device ID 0x0 is not known as SPIFI capable
Error: auto_probe failed
This is because target's JTAG tap->idcode is zero for SWD.
Drop this check completely and hardcode the addresses for now. Neither
the JTAG TAPID nor the SWD IDCODE are unique enough to detect the exact
chip model and thereby its memory map.
Change-Id: Ic230e3e989a3e1f1a5b3bae68bdb34e5ef55d392
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3089
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested with TI MSP-EXP432P401R LaunchPad, via both on-board XDS110-ET (swd)
and external J-Link (jtag).
Change-Id: Ic0caa8516a155754b1c88a04acc8d3c511d9a5f7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3485
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The current configuration leads to the following error when trying to
program the target:
SWD IDCODE 0x2ba01477
timed out while waiting for target halted
TARGET: efm32.cpu - Not halted
in procedure 'program'
in procedure 'reset' called at file "embedded:startup.tcl", line 478
in procedure 'ocd_bouncer'
Use the default reset handling of the target (SYSRESETREQ) to reset the
system rather than SRST to fix the problem.
Tested on EFM32GG, EFM32TG and EZR32WG STK.
Change-Id: I788c41baf08b20814cbe0934b563424c4bc144b8
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3420
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change type of use_raw to boolean. This parameter was already
assigned a boolean variable (in COMMAND_PARSE_ENABLE) and used
as a boolean.
Change-Id: I22f8308246cb25ec9ec2395599e406160410a2a8
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Reviewed-on: http://openocd.zylin.com/3496
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Return ERROR_NAND_DEVICE_NOT_PROBED to prevent calling functions
from segfaulting when nand device has not yet been probed (ie nand
verify)
Change-Id: Ibc4da0aad00e6cc6c83008882b054d981453dc36
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Reviewed-on: http://openocd.zylin.com/3495
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Both the STM32F429I-DISC{O,1} boards are equipped with the same MCU, but
differ by the debugging chip:
- the STM32F429I-DISCO uses the ST-LINK/V2 chip;
- the STM32F429I-DISC1 uses the ST-LINK/V2-B chip (which matches the USB
VID/PID set in stlink-v2-1.cfg).
Change-Id: I07d637f72d26cf5d714472638da974eb6ca02325
Signed-off-by: Samuel Martin <s.martin49@gmail.com>
Reviewed-on: http://openocd.zylin.com/3492
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Memory accesses are not made through the APB-AP, they are made through
the CPU (which happens to be controlled over the APB-AP). Rename all
irrelevant uses of the APB-AP term. And fix the long standing typo in
the function names...
Change-Id: Ide466fb2728930968bdba698f0dd9012cc9dbdf9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3216
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
According to the MSP432P4xx Family TRM (SLAU356A) Figure 4-7,
0x9AF is the part number for MSP432P401xx devices.
Verified on TI MSP-EXP432P401R LaunchPad.
Change-Id: I22b57c42f2a0dc8263fab6b480cf8c169c7dc295
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3486
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Uwe Bonnes
Matthias Welwarsky
Sergey A. Borshch
George Ioakimedes
Tomas Vanek
Olaf Lüke
Andy Pomfret
Andreas Färber
Andreas Bolsch
Felix Held
Andrey Skvortsov
Steven Stallion
Fredrik Hederstierna
Esben Haabendal
Marc Schink
Tim Newsome
Paul Fertser
Ivo Manca
Samuel Martin
Andreas Fritiofson