Remove list of id codes for all families.
Maintain a list with id, bscan-length and check position
in the tcl config files for each family.
The Intel FPGA Driver option 'family' is not otional anymore.
Change-Id: I9a40a041069e84f6b4728f2cd715756a36759c89
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/8083
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
In case of fail to allocate 'obj->name', the memory allocated for
'obj->out_filename' is not freed, thus leaking.
Since 'obj' is allocated with calloc(), thus zeroed, switch to use
the common error exit path for both allocations of 'obj->name' and
'obj->out_filename'.
Fixes: 2506ccb509 ("target/arm_tpiu_swo: Fix division by zero")
Change-Id: I412f66ddd7bf7d260cee495324058482b26ff0c5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8300
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Erase is initiated by write to a flash address. Due to the
silicon errata of nRF91 the write stalls the bus until the page erase
is finished (takes up to 87ms).
If the adapter does not handle SWD WAIT properly, the following read
in nrf5_wait_for_nvmc() returns ERROR_WAIT.
Wait for fixed time before accessing AP. Not nice, but the only
working solution until all adapters handle SWD WAIT.
If the fixed wait does not suffice, continue the wait loop after a delay.
It makes some unnecessary noise however erase works.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I63faf38dad79440a0117ed79930442bd2843c6db
Reviewed-on: https://review.openocd.org/c/openocd/+/8115
Reviewed-by: Tomáš Beneš <tomas@dronetag.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since nRF9160 Product Specification v2.1 the new UICR SIPINFO
fields should be preferred over UICR INFO.
Tested on nRF9161.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib8005b3b6292aa20fa83c1dcebd2de27df58b661
Reviewed-on: https://review.openocd.org/c/openocd/+/8114
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Probes all flash and UICR areas.
Flash erase and write tested.
On nRF53 mass erase works on the application core flash bank only.
The Tcl script nrf53_recover can serve as the workaround on the
network core.
TODO: mass erase of the nRF53 network core flash.
Some ideas taken from [1] and [2].
Change-Id: I8e27a780f4d82bcabf029f79b87ac46cf6a531c7
Link: [1] 7404: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/7404
Link: [2] 8062: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/8062
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8112
Reviewed-by: Tomáš Beneš <tomas@dronetag.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enable and disable erase mode only once
instead of toggling it for each sector.
Refactor to decrease the number of call levels.
Change-Id: Ie546a4fc24da0eea2753a2bebaa63d941ef7aa1d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8111
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Preparatory change before extending support to nRF53 and 91.
While on it, rename nRF51 and 52 specific routines and constants.
Change-Id: I46bc496cef5cbde46d6755a4b908c875351f6612
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8110
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For configurations which include multiple targets and the "pipe" mode is
requested only the first gdb_server instance should be enabled,
otherwise GDB gets confusing replies, goes out of sync and the session
fails in weird ways.
Compile-tested only.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: If8f13aa7b58e9b0dc6d5ae88cf75538b34cc1218
Reviewed-on: https://review.openocd.org/c/openocd/+/8222
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this functionality allows to query if a target belongs to some smp group
and to dynamically turn on/off smp-specific behavior
Change-Id: I67bafb1817c621a38ae4a2f55e12e4143e992c4e
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8296
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
LOG_USER only outputs to user interfaces, but leaves no way to get the
FTDI inputs over the RPC interface. Switch to command_print so this
string goes to both logs and the RPC interface.
Change-Id: I99024194b6687b88d354ef278aa25f372c862c22
Signed-off-by: Mark Featherston <mark@embeddedts.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8294
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
For some target, the API assert_reset() checks if the target has
been examined, with target_was_examined(), to perform conditional
operations like:
- assert adapter's srst;
- write some register to catch the reset vector;
- invalidate the register cache.
Targets created with -defer-examine gets the examine flag reset
right before entering in their assert_reset(), disrupting the
actions above.
For targets created with -defer-examine, move the reset examine
after the assert_reset().
Change-Id: If96e7876dcace8905165115292deb93a3e45cb36
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8293
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 236c54c94a ("server/gdb_server.c: support unavailable
registers") correctly returns a string of 'x' when the register is
not available in the current target.
While implementing this, it incorrectly drops the pre-existing
feature of optionally ignoring errors while reading a register.
This feature has a real use case documented in the OpenOCD manual
in chapter 'Using GDB as a non-intrusive memory inspector', where
GDB attaches to a target without halting it. For targets that need
to be halted to read its registers, we need to hack the values of
the registers returned to GDB; either returning 'xxxx' or an error
causes GDB to drop the connection.
Re-add the check on 'gdb_report_register_access_error' to keep the
pre-existing behavior when a register error has to be ignored:
- return a string of '0';
- drop a debug message.
Change-Id: Ie65c92f259f92502e688914f334655b635874179
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 236c54c94a ("server/gdb_server.c: support unavailable registers")
Reviewed-on: https://review.openocd.org/c/openocd/+/8228
Tested-by: jenkins
Few files include target_type.h even if it is not needed.
Drop the include.
Other files access directly to target type's name instead of using
the proper API target_type_name().
Use the API and drop the include.
Change-Id: I86c0e0bbad51db93500c0efa27b7d6f1a67a02c2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8260
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
clang doesn't support the gnu_printf attribute that OpenOCD uses if
__GNUC__ and __GNUC_MINOR__ indicates gcc >= 4.4.
Most clang builds set __GNUC__/__GNUC_MINOR__ to 4.2 for historical
reasons, so they don't trigger this condition; however, some builds set
it to something much higher to work around code using __GNUC__ to
determine if a feature that does exist in clang (but not gcc 4.2) is
available, causing OpenOCD to use attribute gnu_printf.
The problem can be reproduced without a special clang build by adding
-fgnuc-version=14.1 to CFLAGS.
Change-Id: I3c0832d4201578b116c5214203f95b6153dad30e
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8258
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Do not free the service in 'connection_closed_handler' because it is
free'd by the server infrastructure.
Checkpatch-ignore: COMMIT_LOG_LONG_LINE
This error was detected with valgrind:
==272468== Invalid free() / delete / delete[] / realloc()
==272468== at 0x484B27F: free (in /usr/libexec/valgrind/vgpreload_memcheck-amd64-linux.so)
==272468== by 0x1F34C7: remove_service (server.c:374)
==272468== by 0x2ED3D5: semihosting_tcp_close_cnx (semihosting_common.c:1819)
==272468== by 0x2ED3D5: handle_common_semihosting_redirect_command (semihosting_common.c:1926)
==272468== by 0x1FC703: exec_command (command.c:520)
==272468== by 0x1FC703: jim_command_dispatch (command.c:931)
==272468== by 0x36980F: JimInvokeCommand (in /home/marc/openocd/build/src/openocd)
==272468== by 0x1FFFFFFFFF: ???
==272468== by 0x53ED09F: ???
==272468== by 0x300000001: ???
==272468== by 0x1FFEFFF7FF: ???
==272468== by 0x3D3984: ??? (in /home/marc/openocd/build/src/openocd)
==272468== by 0x2: ???
==272468== Address 0x5fff650 is 0 bytes inside a block of size 24 free'd
==272468== at 0x484B27F: free (in /usr/libexec/valgrind/vgpreload_memcheck-amd64-linux.so)
==272468== by 0x2ECA42: semihosting_service_connection_closed_handler (semihosting_common.c:1807)
==272468== by 0x1F2E39: remove_connection.isra.0 (server.c:164)
==272468== by 0x1F349E: remove_connections (server.c:350)
==272468== by 0x1F349E: remove_service (server.c:364)
==272468== by 0x2ED3D5: semihosting_tcp_close_cnx (semihosting_common.c:1819)
==272468== by 0x2ED3D5: handle_common_semihosting_redirect_command (semihosting_common.c:1926)
==272468== by 0x1FC703: exec_command (command.c:520)
==272468== by 0x1FC703: jim_command_dispatch (command.c:931)
==272468== by 0x36980F: JimInvokeCommand (in /home/marc/openocd/build/src/openocd)
==272468== by 0x1FFFFFFFFF: ???
==272468== by 0x53ED09F: ???
==272468== by 0x300000001: ???
==272468== by 0x1FFEFFF7FF: ???
==272468== by 0x3D3984: ??? (in /home/marc/openocd/build/src/openocd)
==272468== Block was alloc'd at
==272468== at 0x484DA83: calloc (in /usr/libexec/valgrind/vgpreload_memcheck-amd64-linux.so)
==272468== by 0x2ED326: handle_common_semihosting_redirect_command (semihosting_common.c:1931)
==272468== by 0x1FC703: exec_command (command.c:520)
==272468== by 0x1FC703: jim_command_dispatch (command.c:931)
==272468== by 0x36980F: JimInvokeCommand (in /home/marc/openocd/build/src/openocd)
==272468== by 0x1FFFFFFFFF: ???
==272468== by 0x53ED09F: ???
==272468== by 0x400000002: ???
==272468== by 0x1FFEFFF7FF: ???
==272468== by 0x3D3984: ??? (in /home/marc/openocd/build/src/openocd)
==272468== by 0x2: ???
==272468==
Change-Id: I3e5323f145a98d1ff9ea7d03f87ed96140f49a18
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8257
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Currently, errors in pre/post-enable events are ignored and capturing is
always started, even if necessary device configuration fails. This
behaviour is confusing to users. Also, the TPIU must be disabled before
re-configuration is possible.
Start capturing and enable TPIU only if no errors in pre/post-enable
events occurred.
Change-Id: I422033e36ca006e38aa4504d491b7947def1237a
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8254
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When external capturing is configured (default), the SWO pin frequency
is required. Enforce this to avoid a division by zero error.
While at it, ensure that the 'out_filename' variable always contains a
valid string. This saves a few checks and makes the code more clean and
readable.
Change-Id: If8c1dae9549dd10e2f21d5b896414d47edac9fc2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8224
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For MPU configs, determine memory access rights
by probing protection TLB. Issuing IHI without execute
permissions can trigger an exception.
No new clang static analyzer warnings.
Change-Id: Iea8eab5c2113df3f954285c3b9a79e96d41aa941
Signed-off-by: Ian Thompson <ianst@cadence.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8080
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Historically, the function cortex_a_dap_write_memap_register_u32()
was used to discriminate the register write in APB-AP CPU debug
against the complex memory access in AHB-AP memory bus.
It has no sense to keep the function and its comment.
Plus, by forcing atomic write it impacts the debug performance.
Drop it!
A further rework to enqueue sequence of atomic writes is needed.
Change-Id: I2f5e9015f0e27fa5a6d8337a1ae25e753e2e1d26
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8231
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
The command 'cache auto' was introduced with commit cd440bd32a
("add armv7a_cache handlers") in 2015 to allow disabling the cache
handling done automatically by OpenOCD.
This was probably a way to test the cache handling when there were
still the two independent accesses for APB-AP CPU debug and for
AHB-AP memory bus.
The handling of cache for cortex_a is robust and there is no more
reason to disable it.
The command 'cache auto' is not used in any upstream script.
On target aarch64 this command has never been introduced as the
cache is always handled automatically by OpenOCD.
Drop the command 'cache auto' and add it in the deprecated list.
Drop the flag 'auto_cache_enabled' by considering it as true.
Rename the function 'armv7a_cache_auto_flush_all_data()' as
'armv7a_cache_flush_all_data()' and, while there, fix the error
propagation in SMP case.
Change-Id: I0399f1081b08c4929e0795b76f4a686630f41d56
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8230
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The initial OpenOCD code for Cortex-A (ARMv7a) [1] was merged in
2009 but, due to lack of public documentation for ARMv7a, it was
almost a simple copy/paste from the existing code for Cortex-M
(ARMv7m).
On Cortex-M the same AP provides access to both CPU debug and CPU
memory. This feature is not present on ARMv7a.
To still keep some communality with ARMv7m code, the change [2]
splits the CPU debug access from the CPU memory access by using
two independent AP; this is copied from the system architecture of
TI OMAP3530 which provides to DAP a direct AHB-AP memory bus on
AP#0, separated from AP#1 for the APB-AP CPU debug.
But the direct memory access through the system bus breaks the
coherency between memory and CPU caches, so change [3] added some
cache invalidation to avoid issues.
The code to allow ARMv7a CPU to really read/write in CPU memory
was added by change [4] in 2011. Such still not optimized
implementation was very slow, so it did not replace the access
through the system bus. A selection through DAP's 'apsel" command
was used to select between the two modes.
Only in 2015, with change [5], the speed of CPU read/write was
improved using the DCC_FAST_MODE. But the direct access to the
memory through the system bus remained.
Finally, with change [6] in 2018 the system bus access was dropped
for good, as the new virtual target "mem_ap" could implement such
access in a more clean way.
Only memory access through CPU remained for ARMv7a.
Nevertheless, a useless cache invalidation remained in the code,
decreasing the speed of the write access.
Drop the useless cache invalidate on CPU memory write and the
associated comment, not anymore valid.
Drop the now unused function armv7a_cache_auto_flush_on_write().
This provides a speedup of between 4 and 8, depending on adapter
and JTAG/SWD speed.
Link: [1] 7a93100c2d ("Add minimalist Cortex A8 file")
Link: [2] 1d0b276c9f ("The rest of the Cortex-A8 support from Magnus: ...")
Link: [3] d4e4d65d28 ("Cache invalidation when writing to memory")
Link: [4] 05ab8bdb81 ("cortex_a9: implement read/write memory through APB-AP")
Link: [5] 0228f8e827 ("Cortex A: fix extra memory read and non-word sizes")
Link: [6] fac9be64d9 ("target/cortex_a: remove buggy memory AP accesses")
Change-Id: Ifa3c7ddf2698b2c87037fb48f783844034a7140e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8229
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fix possible double free and possible
memory leak while creating an ipdbg hub.
Change-Id: I6254663c27c4f38d46008c4dbff11aa27b84f399
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/8085
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The gdb subsystem is initialized after the first target examine,
so the field struct target::gdb_service is NULL during examine.
A command "smp off" in the examine event handler causes a SIGSEGV
during OpenOCD startup.
Check for pointer not NULL before dereferencing it.
Change-Id: Id115e28be23a957fef1b97ab66d7273f0ea0dce4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8216
Tested-by: jenkins
The code for cortex_a allocates the register cache during the very
first examine of the target.
To prevent a segmentation fault in assert_reset(), the call to
register_cache_invalidate() is guarded by target_was_examined().
But for targets with -defer-examine, the target is set as not
examined in handle_target_reset() just before entering in
assert_reset().
This causes registers to not be invalidated while reset a target
examined but with -defer-examine.
Change the condition and invalidate the register cache if it has
been already allocated.
Change-Id: I81ae782ddce07431d5f2c1bea3e2f19dfcd6d1ce
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8215
Tested-by: jenkins
The code for aarch64 allocates the register cache during the very
first examine of the target.
To prevent a segmentation fault in assert_reset(), the call to
register_cache_invalidate() is guarded by target_was_examined().
But for targets with -defer-examine, the target is set as not
examined in handle_target_reset() just before entering in
assert_reset().
This causes registers to not be invalidated while reset a target
examined but with -defer-examine.
Change the condition and invalidate the register cache if it has
been already allocated.
Change-Id: Ie13abb0ae2cc28fc3295d678c4ad1691024eb7b8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8214
Tested-by: jenkins
Prevent a segmentation fault by preventing to try to halt a target
that has not been examined yet.
Change-Id: I5d344e7fbdb5422f7c5e2c39bdd48cbc6c2a3e58
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8213
Tested-by: jenkins
Commit 16b4b8cf54 ("Cortex-M3: expose most DWT registers") added
the DWT registers to the list of CPU registers.
The commit message from 2009 reports the reason behind this odd
mixing of CPU and DWT registers.
This feature got broken in 2017 with the introduction of the field
struct reg::exist and its further use in the code. As result, the
command 'reg' on a target Cortex-M reports only the core registers
and then the header line
===== Cortex-M DWT registers
not anymore followed by the DWT registers.
Fix it by tagging each DWT registers as existing.
Change-Id: Iab026e7da8d6b8ba052514c3fd3b5cdfe301f330
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: b5964191f0 ("register: support non-existent registers")
Reviewed-on: https://review.openocd.org/c/openocd/+/8198
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Checkpatch complains for extra parenthesis not required.
Drop them.
Change-Id: I311409f5732acf10a4910de5dcf0fb05f43e21b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8187
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Initialized `value` variables that could only be set in a branch.
Change-Id: Iec7413ade9d053c93352a58ff954ad49a6545923
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8179
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It was noticed that the remote_bitbang protocol has a design issue:
SWD and sleep commands cannot be implemented at the same time, because
they overlap:
- SWD uses d,e,f,g for setting pin state
- sleep uses d,D for microsecond and millisecond sleep, respectively
This has previously been reported by Marek Vrbka, but it wasn't fixed.
This commit does the following to resolve the issue:
- Change the sleep commands to 'Z' for 1 ms, 'z' for 1 µs
- Document 'D' and 'd' as deprecated aliases
- Switch the remote_bitbang driver in OpenOCD to 'Z' and 'z'
Unfortunately that's a breaking change, because existing adapter-side
implementations of the protocol will have to implement the new commands
to keep working with future versions of OpenOCD. Fortunately, the
remote sleep commands haven't been part of an OpenOCD release yet,
which should limit the breakage somewhat.
Reported-by: Marek Vrbka <marek.vrbka@codasip.com>
Link: https://sourceforge.net/p/openocd/mailman/openocd-devel/thread/670d28d2-75a1-45ec-afe5-541415701d7a%40codasip.com/
Fixes: e8e09b1b5 ("remote_bitbang: add use_remote_sleep option to send delays to remote")
Change-Id: I04d2790a33bff9d47eb7f69b3275fd9a271625ae
Signed-off-by: J. Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.openocd.org/c/openocd/+/8191
Reviewed-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jeremy Herbert <jeremy.006@gmail.com>
Commit 290eac04b9 ("drivers/linuxgpiod: Migrate to adapter gpio
commands") introduced an incorrect check to determine if the
library libgpiod declares the line request flags:
GPIOD_LINE_REQUEST_FLAG_BIAS_DISABLE
GPIOD_LINE_REQUEST_FLAG_BIAS_PULL_UP
GPIOD_LINE_REQUEST_FLAG_BIAS_PULL_DOWN
The names above are declared by the library inside an enum, thus
cannot be used by the C preprocessor in a #ifdef.
Determine in configure if the version of libgpiod provides the
line request flags for "bias" and define a C macro.
Use the new macro in the driver code.
Change-Id: Iaa452230f4753fce4c6e9daa254299cedb7cab7f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 290eac04b9 ("drivers/linuxgpiod: Migrate to adapter gpio commands")
Reviewed-on: https://review.openocd.org/c/openocd/+/8186
Tested-by: jenkins
Reviewed-by: Michael Heimpold <michaheimpold@gmail.com>
Move setting of do_reconnect flag from swd_run_inner()
to swd_run(). Reconnect is not used at the inner level
and the flag had to be cleared after swd_run_inner()
to prevent recursion.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib1de80bbdf10d1cbfb1dd351c6a5658e50d12af2
Reviewed-on: https://review.openocd.org/c/openocd/+/8155
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The file 'list.h', copied from FreeBSD, does not depend from any
OpenOCD specific include file, but only needs 'stddef.h' for the
type 'size_t'.
Let 'list.h' to include the correct header file, then fix the now
broken dependencies in the other files that were incorrectly
relying on 'list.h' to include 'helper/types.h'
Change-Id: Idd31b5bf607e226cac44ef41b2aa335ae4dbf519
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8173
Tested-by: jenkins
The file list.h was originally taken from the Linux kernel code,
thus under license GPL-2.0-only. This locks OpenOCD to follow the
same license, even if the majority of OpenOCD files are licensed
as GPL-2.0-or-later.
A similar file is also present in FreeBSD code base under the more
permissive license BSD-2-Clause.
Drop the code from Linux kernel and replace it with the code from
FreeBSD 13.3.0.
Adapt the code to OpenOCD coding style by fixing the majority of
issues identified by checkpatch.
Add the OpenOCD specific macros and comments.
Unfortunately this causes the lost of all the doxygen comments.
Checkpatch-ignore: MACRO_ARG_REUSE, MACRO_ARG_PRECEDENCE
Change-Id: I6d86752c50158f3174c4e8c4add81e9998d01e0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8172
Tested-by: jenkins
OpenOCD can send it's log to gdb, and gdb replies with 'OK'.
Calls to LOG_XXX() are also present in the code that communicates
with gdb. This can cause infinite nested calls.
OpenOCD uses the flag 'gdb_con->busy' to protect the communication
with gdb and prevent nested calls.
There is no reason to check for 'gdb_con->busy' in the code for
keep-alive, as keep_alive() is never called in this gdb server;
the flag would eventually be set if the current keep_alive() will
send something to gdb.
Drop the flag 'gdb_con->busy' in gdb_keep_client_alive().
While there, document the use of 'gdb_con->busy'.
Change-Id: I1ea20bf96abb5d2f1fcdba1e3861df257c396bb6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8166
Tested-by: jenkins
To avoid gdb to timeout, OpenOCD implements a keep-alive mechanism
that consists in sending periodically to gdb empty strings embedded
in the "O" remote reply packet.
The main purpose of "O" packets is to forward in the gdb console
the output of the remote execution; the gdb-remote puts in the "O"
packet the string that gdb will print. It's use is restricted to
few "running/execution" contexts listed in
http://sourceware.org/gdb/onlinedocs/gdb/Stop-Reply-Packets.html
and this currently limits the keep-alive capabilities of OpenOCD.
Long data transfer (memory R/W) can also cause gdb to timeout if
the interface is too slow. In this case the usual keep-alive based
on "O" packet cannot be used and, if used, would trigger a protocol
error that causes the transfer to be dropped.
The slow transfer rate can be simulated by adding some delay in the
main loop of mem_ap_write() and mem_ap_read(), then using the gdb
commands "dump" and "restore".
In the wait loop during a memory R/W, gdb drops any extra character
received from the gdb-remote that is not recognized as a valid
reply to the memory command. Every dropped character re-initializes
the timeout counter and could be used as keep-alive.
From gdb 7.0 (released 2009-10-06), an asynchronous notification
can also be received from gdb-remote during a memory R/W and has
the effect to reset the timeout counter, thus can be used as
keep-alive.
The notification would be treated as "junk" extra characters by any
gdb older than 7.0, being still valid as keep-alive.
Check putpkt_binary() and getpkt_sane() in gdb commit
74531fed1f2d662debc2c209b8b3faddceb55960
Currently, only one notification packet ("Stop") is recognized by
gdb, and gdb documentation reports that notification packets that
are not recognized should be silently dropped.
Use 'set debug remote 1' in gdb to dump the received notifications
and the junk extra characters.
Add a new level in enum gdb_output_flag for using the asynchronous
notifications.
Activate this new level during memory transfers.
Send a custom "oocd_keepalive" notification packet as keep_alive.
While there, drop a useless return in the switch/case, already
managed in case of break.
After this commit, the proper calls to keep_alive() have to be
added in the loops that code the memory transfers. Of course, the
keep_alive() should be placed during the wait for JTAG flush, not
while locally queuing the JTAG elementary transfers.
Change-Id: I9ca8e78630611597d15984bd0e8634c8fc3c32b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8165
Tested-by: jenkins
Add access to fpr and cp1 registers.
GDB can now check the FPRs with `info reg f` and change them.
Checkpatch-ignore: MACRO_ARG_REUSE
Change-Id: I63896ab6f6737054d8108db105a13a58e1446fbc
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7866
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
To simplify the ipdbg start/stop command and be able to
add additional commands in the future, we introduce the
concept of a hub which has to be created before a
ipdbg server can be started.
The hub was created on the fly in previous versions.
Change-Id: I55f317542d01a7324990b2cacd496a41fa5ff875
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7979
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When receiving an OpenOCD debug log to investigate about errors or
issues, the first question is often about providing the complete
command line to better understand the use context.
Plus, when OpenOCD is lunched by an IDE, its command line is kept
hidden inside the IDE, adding troubles to the user to recover it.
Add the full command line directly inside the debug log.
It could have been useful to also search and add in the log the
full path of the OpenOCD executable, but this is not an immediate
task due to portability among OS's. See, for example:
https://stackoverflow.com/questions/933850
This part could be handled in a future change, if really needed.
Change-Id: Ia6c5b838b9b7208bf1ecac7f95b5efc319aeabf5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8170
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Extend the existing code to support Monitor mode in AArch32.
Change-Id: Ia43df98d1497baac48aea67b92d81344c24f0635
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8169
Tested-by: jenkins