All DIDs are taken from "SAM R34/R35 Errata Sheet" (DS80000834A).
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: Ie35f58e61bb02919c0676c91938c90192481d995
Reviewed-on: https://review.openocd.org/c/openocd/+/7521
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to the datasheets these MCUs have 40Kb RAM.
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: I52b8a0c86035bccd6f3c1a478bb2e558bca4ae86
Reviewed-on: https://review.openocd.org/c/openocd/+/7520
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The driver tries to open mpsse engine for each vid pid
pair in sequence. If more vid/pid pairs are configured and
the USB device does not correspond to the first pair,
the driver shows 'unable to open ftdi device ...' error.
Match vid pid with the whole list as used in jtag_libusb_open()
instead of multiple mpsse_open() in for loop over vid/pid pairs.
Change-Id: I8ef55205be221c727607fe25b81ae21de0d96f02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7529
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Can be employed by a driver with custom libusb open.
Change-Id: I00c8a01df8780891a8b7c30e2e34ab191acdf9a8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7528
Tested-by: jenkins
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
SAM9260 gained good generic infrastructure since 2009. And we always
want "improvements", no need for a TODO item.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I92551ef9d42ee47ad7441f2354587bbb45edc97e
Reviewed-on: https://review.openocd.org/c/openocd/+/7526
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It was fixed by e94180571 ("at91sam9: factorise cpu support") in 2011.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I95ea149b45a9902424bf9068b4a2830c17ddc6be
Reviewed-on: https://review.openocd.org/c/openocd/+/7525
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
in raspberrypi-native.cfg
Fixes: bec6c0eb09 (tcl/interface: universal config for all Raspberry Pi models)
Signed-off-by: Tomas Deingruber <Deingruber.Tomas@gmail.com>
Change-Id: I632c8acd84974937849b5fdf2943239def17bd6d
Reviewed-on: https://review.openocd.org/c/openocd/+/7512
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We currently fail the transfer when issuing more than 255 transactions
at once, e.g.
> read_memory 0x10000000 32 256
CMSIS-DAP transfer count mismatch: expected 257, got 1
This is because the protocol only supports 255 transactions per packet
(65535 for block transactions), and as a result we truncate the
transaction count when assembling the packet. Fix it by running the
queue when we hit the limit.
Change-Id: Ia9e01e3af5ad035f2cf2a32292c9d66e57eafae9
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 40bac8e8c4 ("jtag/drivers/cmsis_dap: improve USB packets filling")
Reviewed-on: https://review.openocd.org/c/openocd/+/7483
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OpenOCD commands produce their TCL text result through the
pair command_print() and command_print_sameline().
The latter is used to concatenate output in a single line.
At the end of a sequence of command_print(), the last LF is taken
as part of the command result, while it is not always needed, and
it is even annoying when the output of two commands needs to be
concatenate in a single line.
Using command_print_sameline() in place of the last call to
command_print() would solve the problem but it's quite expensive
in term of coding to fix all the existing commands.
Drop the last LF, if present.
Commands that would specifically need a LF as last char, can add
an extra LF at the end of the output.
Document this behavior in command.h.
Change-Id: I6757c20fbfce923dd393083146e8d5a1f3b790b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7471
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A bunch of new SPI flash (Adesto, Cypress, XTX Tech, mainly octal)
IDs and SPI FRAM (Infineon) IDs added. Backward compatible change
of ID interpretation: The previously unused 4th byte now acts
as continuation code (0x7F) count for manufacturer id, cf.
JEDEC JEP106BC. Currently this affects only some recent octal flash
and FRAM devices, which are only supported by stmqspi and cmspi
flash drivers.
Change-Id: Ibdcac81a84c636dc68439add4461b959df429bca
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6929
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While there, fix some coding style error and remove the now unused
function jim_arc_read_reg_name_field() and the macro
JIM_CHECK_RETVAL().
Change-Id: I140b4b929978b2936f2310e0b7d1735ba726c517
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7426
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Use a COMMAND_HELPER() to avoid memory leaks when the helper
COMMAND_PARSE_NUMBER() returns due to an error.
While there:
- fix potential SIGSEGV due to dereference 'type' before checking
it's not NULL;
- fix an incorrect NUL byte termination while copying to
type->data_type.id and to bitfields[cur_field].name;
- fix some coding style error;
- remove the now unused function jim_arc_read_reg_type_field().
Change-Id: I7158fd93b5d4742f11654b8ae4a7abd409ad06e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7425
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Use a COMMAND_HELPER() to avoid memory leaks when the helper
COMMAND_PARSE_NUMBER() returns due to an error.
While there:
- fix potential SIGSEGV due to dereference 'type' before checking
it's not NULL;
- fix an incorrect NUL byte termination while copying to
type->data_type.id and to bitfields[cur_field].name;
- fix some coding style error.
Change-Id: Ide4cbc829871a6a523026ccc0d3100dadc2afd06
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7424
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Long ago jim_nvp was part of jimtcl. When jimtcl dropped it,
OpenOCD kept copy of it in its code base. Current code of jim_nvp
is still related with jimtcl data types and functions.
With the target of better isolating OpenOCD code from jimtcl,
create a new file nvp.c that re-proposes only the core of the old
jim_nvp, dropping any link with jimtcl and removing the string
'jim' either from the filename and from the code.
Keep the same license from the old code, as the new files are
clearly derived from it.
Change-Id: I273448cf1f1484b10f6b6113ed7bb0fcf946482b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7423
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
The command is specified through COMMAND_HANDLER. It should not
return JIM_OK / JIM_ERR.
Change-Id: I56666414d49b0298ecc23ec7ef30c77e1e27afa8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7413
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Also drop arc_cmd_jim_get_uint32() that is now unused.
Change-Id: Ic26c3f008376db3f01215bf736fca736dd1c1a4f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7412
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes several incorrect return ERROR_xxx from a jim
command.
Change-Id: I34fe3552d3dc344eac67bf504c5d5709b707fdfd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7411
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I72a522645f62b99b313573c8bad6d4f674c5ae53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7410
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I1f9cf5d1dfa38b8a06042b5f54209e6ee2fc4e0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7409
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: Iab9bc7c25181341a632f608a8ef2d8b0bea72520
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7408
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I3c51355e7e05965327ce819a3114e370f2de5249
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7407
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Integrate a rescue mode inspired by [1].
The current OpenOCD must be restarted before normal work with the RP2040
because the rescue debug port must not be activated (or the target
is reset every 'dap init'). To continue without restarting OpenOCD
we would need to switch off the configured rescue dap.
Change-Id: Ia05b960f06747063550c166e461939d92e232830
Link: [1] https://github.com/raspberrypi/openocd/blob/rp2040/tcl/target/rp2040-rescue.cfg
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7327
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
SW-DPv2 and SWJ-DPv2 devices do not reply to DP_TARGETSEL write cmd.
Ignore the received ACK after TARGETSEL write.
While on it, use swd_ack_to_error_code() for unified error code
translation of the received ACK value for all other commands.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If978c88c8496e31581175385e59c32faebfd20aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
And add its own header to the rtos_xxx_stackings.c
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I084130fde7ee8645129a7cf60bb7bf59448e2f39
Reviewed-on: https://review.openocd.org/c/openocd/+/7441
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Speed calibration coeffs are computed from cpufreq/scaling_max_freq
and from the device-tree compatibility information.
Raspberry Pi linux offers /dev/gpiomem for non-root access
to the GPIO registers since ~2016.
Do not configure 'bcm2835gpio peripheral_base' as it is necessary
only if /dev/mem is used - it requires running OpenOCD as root
- it's a security risk so it should be avoided.
The configuration of the GPIO connector (40-pin header)
is factored out and ready to use in interface configuration
for other driver (e.g. linux gpiod).
Mark raspberrypi2-native.cfg as deprecated and redirect
it to raspberrypi-native.cfg
Change-Id: Icce856fb660b45374e94174da279feb51f529908
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7264
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
No functional change, the delay is unchanged.
Change-Id: I5b5e837d741ac01fc573657357c5fe61ad901319
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7262
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After setting adapter speed to some values, the driver
shows the real speed little bit higher.
Although it does not impose a problem from technical point
of view because the difference is smaller than usual speed error,
it looks at least strange to the user. The documentation reads
that real frequency should be same or lower than requested.
Use proper rounding in speed -> delay and delay -> speed
conversions.
Change-Id: I1831112cc58681875548d2aeb688391fb79fa37f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7261
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
bitbang_swd_exchange(rnw=true,...) calls bitbang_interface->swd_write()
with swdio clamped to 0.
bitbang_swd_write_reg() reads 1 turnaround bit, 3 ack bits
and 1 turnaround by one call to bitbang_swd_exchange()
and then switches SWDIO to output.
AFAIK all bitbang interfaces switch SWDIO GPIO direction immediately
in bitbang_interface->swdio_drive().
The GPIO now drives SWDIO line to the value stored in the output register
which is always zero from previous bitbang_swd_exchange(rnw=true,...).
In case the following data bit (bit 0) is 1 we can observe a glitch
on SWDIO:
_____ out 1 ____
HiZ/pull-up ----\ /
\ /
\______ out 0 ______/
swdio_drive(true) swd_write(0,1)
The glitch fortunately takes place far enough from SWCLK rising edge
where SWDIO is sampled by the target, so I believe it is harmless
except some corner cases where the reflected wave is delayed on long
line.
Anyway keeping electrical signals glitch free is a good practice.
To keep performance penalty minimal, pre-write the first data
bit to SWDIO GPIO output buffer while clocking the turnaround bit.
Following swdio_drive(true) outputs the pre-written value
and the same value is rewritten by the next swd_write()
instead of glitching SWDIO.
Change-Id: I72ea9c0b2fae57e8ff5aa616859182c67abc924f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7260
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The OpenJTAG driver logs "num_cycles > 16 on run test" warning
whenever the JTAG_RUNTEST operation cycle count is larger than 16.
Instead of logging the warning and only running the first 16 TCLK
cycles, remove the warning and queue up multiple operations of up
to 16 cycles each.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Id405fa802ff1cf3db7a21e76bd6df0c2d3a0fe61
Reviewed-on: https://review.openocd.org/c/openocd/+/7420
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Works for the proprietary rt-kernel from rt-labs.
See: https://rt-labs.com/product/rt-kernel/
Change-Id: Id2c2e292c15fb17eab25e3d07db05014daa2a2b0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6668
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is optional field for the targets which has to implement
their custom stack read function.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Icbc9ed66a052fc2cc0ef67e3ec4d85ab0c2c1b94
Reviewed-on: https://review.openocd.org/c/openocd/+/7442
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Other OSes have separate files to keep stack register offsets.
Adding them for NuttX as well will provide a clearer way to expand.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1428fefefa199a95431f2073c0279dd7028ad8da
Reviewed-on: https://review.openocd.org/c/openocd/+/7250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
URL for Microsoft documentation on IgnoreHardwareSerialNumber
redirects to generic USB driver landing page instead of specific
article. Update link to go to correct page.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Ifac6c730a1438242cdfe0a0a2867e043e03ceec7
Reviewed-on: https://review.openocd.org/c/openocd/+/7439
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Same mechanism as in stm32f1x.cfg reused here.
Change-Id: I81f02feb2b655e8259341b22180f3a8b82e28d05
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7438
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This generalizes the little endian CRC32 function used in the OR1K
target and moves it to a common helper, so that other places do not need
to reinvent the wheel. It is directly used in the OR1K target.
Change-Id: I0e55340281a5bfd80669bb1994f3a96fecc1248a
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7415
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Polling the target makes no harm during PSoC 4 flash write in the current
OpenOCD code. Don't mask it.
Change-Id: I6625ded0162ee3a96b92188844d0d2d6c30101c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7162
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The commands 'jtag newtap' and 'swd newdap' have to work either on
HLA transport and on standard JTAG/SWD. Having a dedicated
implementation for HLA is a non-sense.
Reuse the generic code jim_jtag_newtap() and drop the files
hla_tcl.[ch] as they are now empty.
Change-Id: I9dabbdc2a6f338f23b2fd3ed1a4dc3da0200c080
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7428
Tested-by: jenkins
The same code is currently used for commands 'jtag newtap' and
'swd newdap' (plus dapdirect versions), but for SWD case the code
skips the parsing of the command line as not every flag is used.
This has the drawback that syntax errors get unchecked.
Move the check about the transport so the command line get always
parsed even when the corresponding flags are not useful.
Change-Id: I596c3beb04e9e8a9ebe6ee68a61395b679d43b3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Enhancing the editor / IDE experience with the use of the language
server protocol (lsp) is getting more and more common. The most widely
used lsp implementation for C/C++ outside of Redmond is clangd.
Clangd uses compile_commands.json, that contains the compiler invocation
for each compilation unit, to get the required $CFLAGS to successfully
located header files etc. This is best automatically generated from with
bear on Makefile based build systems. Hence, there is little value in
adding it to the git repo.
In addition, clangd generates cache files in the .cache folder. Again,
there is no reason in tracking it with git.
Change-Id: Ic5165d10aca3a1cc9e9398af9dd2fbf0977608b3
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7414
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The rtos hwthread has been merged in 2019 with commit 85ba2dc4c6
("rtos/hwthread: add hardware-thread pseudo rtos").
During review in patchset 19 the name of the rtos has been changed
from 'hawt' to 'hwthread'.
Some target config file was already merged ready for hwthread, but
keeping the relevant lines commented and still reporting the old
name.
Enable rtos hwtread to the target that were supposed to use it.
Fix the name of the rtos.
Change-Id: I877862dcdba39f26462bb542bac06d1a5f5f222d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7384
Tested-by: jenkins
The line reset SWD sequence is used quite often in SWD multidrop mode.
Prevent the ugly connect/disconnect adapter firmware bug workaround
to be called before each line reset.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id85bff075dba9077e4e501e2cdcfd64d5d9d0531
Reviewed-on: https://review.openocd.org/c/openocd/+/7381
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Andrew Lalaev
Tomas Vanek
Wolfram Sang
Tomas Deingruber
Peter Collingbourne
Antonio Borneo
Daniel Anselmi
Andreas Bolsch
Marc Schink
Daniel Serpell
Erhan Kurubas
N S
Andreas Fritiofson
Marian Buschsieweke