Now logging is consistent and more readable.
I did remove most logging during riscv_poll() since it clutters up the
log/screen and is not generally helpful.
Users can use this register to inspect and change the privilege level of
the core. It doesn't make any assumptions about the actual underlying
debug mechanism (as opposed to having the user change DCSR directly,
which may not exist in all debug implementations).
Now you can attach with gdb, and it'll attempt to read a register. That
will fail because the core won't clear debug interrupt. Adding nops
doesn't help this time.
target_run_flash_async_algorithm() ignored abort from target
(rp set to 0) when raised after all data have been written in fifo.
I could result e.g. in not reported error during flash write.
The change adds rp test after target algorithm has finished.
Change-Id: Iadd93371e4a4602737be10079479285d81ae41b2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3560
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- FPU detection and FPU register support added for Cortex-M7.
There is no apparent difference between FPv4 and FPv5_SP but ...
- Autoincrement range for MEM-AP added for Cortex-M7
This patch together with #3526 replaces #3123 except for stm32f7x.cfg.
Change-Id: I5ed5392e3835674160563ff37d67622a7bf2c877
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/3531
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If WAIT recovery fails (times out), an ABORT command is issued to the
DAP but under some conditions the SSTICKYORUN bit in CTRL/STAT is not
cleared as well, which renders the DP unusable. This happens when
trying to access e.g. the ROM table of powered-down cores, on many
targets.
Change-Id: Id0a7ba6180069eee562871314f520f938df9718f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3476
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Allow using physical addresses with mem2array and array2mem. In order
to minimize the impact on existing scripts, "phys" is added as an
optional 5th parameter to both commands.
This patch also adds "phys" variants to the memwrite/memread commands
in memory.tcl.
Change-Id: Ia6307f9d861789e7f3ccf1f98961d666bf8d85d6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3387
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Sometimes it is necessary to resume into a different state (ARM/Thumb)
than at debug state entry. According to the documentation this should
be possible with "arm core_state arm|thumb" before the resume command,
however the original code also restores the original CPSR, which
overrides whatever state the core was set to. This seems to work on some
cores (e.g. Cortex-A5) but not on others (e.g. Cortex-A9). Using the "BX"
instruction to set resume PC and core state works on Cortex-A9 and
ARM11, but is not sufficient on Cortex-A5, where an explicit write to
the PC (MOV pc, r0) is required additionally.
Change-Id: Ic03153b4b250fbb8cf6c75f8e329fb34829aa35f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3386
Tested-by: jenkins
Reviewed-by: Alexander Stein <alexanders83@web.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
First, fix the timeval_ms() implementation to not have K&R but ANSI
argument semantics by adding a missing void.
timeval_ms() returns an int64_t, not uint64_t or long long. Consistently
use int64_t for variables and PRI*64 as format string.
While at it, change a few related variables to bool for clarity.
Note that timeval_ms() may return a negative error code, but not a
single caller checks for that.
Change-Id: I27cf83e75b3e9a8913f6c43e98a281bea77aac13
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3499
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A developer tool: Direct access to AP registers can be useful
for handling vendor specific AP like Freescale Kinetis MDM or Atmel SMAP.
Change-Id: Ie2c7160fc6b2e398513eb23e1e52cbb52b88d9bd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2777
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Today the reset option for connect_assert_srst is not done for SWD.
This patch adds this to SWD and make it possible to connect to targets which might disable JTAG interface when running.
Change-Id: Ib89f7cf59b628e8f0b5fca9dd9e362e383c4b99f
Signed-off-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-on: http://openocd.zylin.com/3018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The SAP in LS102x SoC's from Freescale is able to read and write to all
physical memory locations, independently of CPU cores and DAP.
This implementation is 100% based on reverse-engineering of JTAG
communication with an LS1021A SAP using a JTAG debugger with SAP support.
And as such, this code is for now "works-for-me", pending verification
by other OpenOCD users, or even better, actual information from Freescale
on the SAP interface.
Change-Id: Ibb30945e017894da5c402f9f633fc513bed4e68c
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Reviewed-on: http://openocd.zylin.com/3096
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv4_5_crc.inc, and convert the code to target
endianness the least intrusive way.
Change-Id: I7452b2c7e679dae14f9cda5f89bc81c16fc12cad
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3473
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Add rules to build armv4_5_erase_check.inc, and convert the code to
target endianness the least intrusive way.
Drop an unused word from the assembler sources to make the ARM bytecode
fully match that of armv4_5.c and to not break ARMv4 assumptions.
This completes the build rules for contrib/loaders/erase_check directory.
Change-Id: I36be7a944e26142088195fa3fb072d4e577bf328
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3135
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv7m_crc.inc and include it via preprocessor.
Change-Id: I4482c7acb8454de28bdf210d9f06c0720ada490a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3474
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: Ie3f95f992a98a1325428e4032a1c17346d4c9977
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3472
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: I95bb12fbe7c80b594e178468bcd4f6387c682c93
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3471
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Memory accesses are not made through the APB-AP, they are made through
the CPU (which happens to be controlled over the APB-AP). Rename all
irrelevant uses of the APB-AP term. And fix the long standing typo in
the function names...
Change-Id: Ide466fb2728930968bdba698f0dd9012cc9dbdf9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3216
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
According to the MSP432P4xx Family TRM (SLAU356A) Figure 4-7,
0x9AF is the part number for MSP432P401xx devices.
Verified on TI MSP-EXP432P401R LaunchPad.
Change-Id: I22b57c42f2a0dc8263fab6b480cf8c169c7dc295
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3486
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This was found on multiple XMC4500:
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00001c11db
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1db, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
On multiple XMC4700 and an XMC4800 this was found instead:
Valid ROM table present
Component base address 0xe00ff000
Peripheral ID 0x00001c11df
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1df, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
Name them "XMC4500 ROM" and "XMC4700/4800 ROM" respectively.
Change-Id: If369a6d16524004ba439b878f090a313a9f3a760
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3482
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Not documented in the Reference Manuals but found on multiple XMC1100/1202:
Valid ROM table present
Component base address 0xf0000000
Peripheral ID 0x00001c11ed
Designer is 0x0c1, Infineon (Siemens)
Part is 0x1ed, Unrecognized
Component class is 0x1, ROM table
MEMTYPE system memory present on bus
Name it "XMC1000 ROM", since it didn't differ between XMC1100 and XMC1200.
Change-Id: I98a5a524c0d0836f395400fbac24fd496b2ec141
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3481
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Consistently increase the space-indentation of the .full values to
nicely align with the new "Qualcomm QDSS Component v1" .type value.
Change-Id: Icd28d8f3fc7c3afcccb9dcfe138ac57d64927d1a
Suggested-by: Freddie Chopin <freddie.chopin@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3480
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Note:
WCR (Wire Control Register) is replaced by DLCR (Data Link Control
Register). And only TURNROUND field is modifiable.
[andreas.fritiofson@gmail.com]:
Rename DP_IDCODE to DP_DPIDR as well.
Sort list by address and align it using spaces instead of tabs. Add
comments about supporting DP versions.
Remove non-functional wcr command completely.
Change-Id: Ic6b781b07c8eead8b0237d497846d0da060cb1ba
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3244
Tested-by: jenkins
Instead of placing Atmel last, after ANY_ID, place it after ARM (it's
arm_adi_v5 despite 0x4BB) and sort it with the other vendors, i.e.
before ADI and Qualcomm. Adapt column alignment.
Drop the redundant "Atmel" comment to clarify that Analog is not Atmel.
Change-Id: Ic06785db079cf58d49815a639236636c180e5e17
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3479
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On APQ8016 was found a CoreSight component designed by
Qualcomm, according to db410c HRM [1] it has a partnumber
following this schema:
[11:8] is 0x4 meaning Qualcomm designed Coresight component in QDSS. Reads as 0x4.
[7:6] is Subsystem/core family ID (e.g. denote QDSS family or generation).
[5:4] is Subsystem/core configuration options (e.g. denote cache options, etc.).
[3:2] is Subsystem/core fuse options.
[1:0] is Subsystem/core future use field
Reads as 0x440.
[1] - https://developer.qualcomm.com/download/sd410/hardware-register-description-qualcomm-snapdragon-410.pdf
Change-Id: I9b4b41fd17c59d2f5ae35b53278d06d6087665f8
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3408
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
On hi6220 'dap info' returned some unknown components from ARM.
Collected from ARM docs, mostly ROM table entries.
Typo fix for Cortex-M3 FPB.
Change-Id: I96bbf7349061937b3afc8bb8d6d1650f2609f82d
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3407
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Clean up the working area in case writing fails.
Adapted from armv7m_checksum_memory().
Change-Id: I4e5950f568ed70a72a1dcfd77e3321110b17e1de
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3469
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Spotted by gcc:
arm7_9_common.c: In function ‘arm7_9_unset_breakpoint’:
arm7_9_common.c:353:4: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
if (current_instr == arm7_9->thumb_bkpt)
^~
arm7_9_common.c:356:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘if’
if (retval != ERROR_OK)
^~
The logic won't change once the braces have been added, as the new 'retval'
check only makes sense within the if().
Change-Id: I6a303e118f2150e5eb25c9268ad06de5d8a533b2
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Reviewed-on: http://openocd.zylin.com/3477
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The cortex_a specific assert_reset function must only apply nSRST if
the reset configuration states that JTAG can be used while nSRST is
asserted.
Change-Id: If604a65fdea5bcb46ec723ada547a4e8d6fa8c59
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3356
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
I suppose 0xff300008 is the correct value for EJTAG_V20_DBS.
20 miliseconds is too much for scan delay, 2ms is enough in mips_m4k scan_delay handler.
mips32 scan_delay has the correct value.
Change-Id: Ie9dc650065a58e845687058a4c930f85909beec9
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/2271
Tested-by: jenkins
Reviewed-by: Kent Brinkley <jkbrinkley.imgtec@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
BMIPS always needs 2 additional instructions to reach the core.
Seems there is a 2 instructions fifo between the tap and the core, or it behaves in this way.
No idea of the purpose of this fifo, I can only guess.
Of course function mips32_pracc_clean_text_jump() must add this additional instructions (NOPs).
Only tested on bcm3348..
Change-Id: I3183d3ce865d469d7262ba4b15446e5743a5f1df
Signed-off-by: Salvador Arroyo <salvador@telecable.es>
Reviewed-on: http://openocd.zylin.com/2270
Tested-by: jenkins
Reviewed-by: Kent Brinkley <jkbrinkley.imgtec@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Before this change jim_target_reset() checked examined state of a target
and failed without calling .assert_reset in particular target layer
(and without comprehensible warning to user).
Cortex-M target (which refuses access to DP under active SRST):
If connection is lost then reset process fails before asserting SRST
and connection with MCU is not restored.
This resulted in:
1) A lot of Cortex-M MCUs required use of reset button or cycling power
after firmware blocked SWD access somehow (sleep, misconfigured clock etc).
If firmware blocks SWD access early during initialization, a MCU could
become completely inaccessible by SWD.
2) If OpenOCD is (re)started and a MCU is in a broken state unresponsive
to SWD, reset command does not work even if it could help to restore communication.
Hopefully this scenario is not possible under full JTAG.
jim_target_reset() in target.c now does not check examined state
and delegates this task to a particular target. All targets have been checked
and xx_assert_reset() (or xx_deassert_reset()) procedures were changed
to check examined state if needed. Targets except arm11, cortex_a and cortex_m
just fail if target is not examined although it may be possible to use
at least hw reset. Left as TODO for developers familiar with these targets.
cortex_m_assert_reset(): memory access errors are stored
instead of immediate returning them to a higher level.
Errors from less important reads/writes are ignored.
Requested reset always leads to a configured action.
arm11_assert_reset() just asserts hw reset in case of not examined target.
cortex_a_assert_reset() works as usual in case of not examined target.
Change-Id: I84fa869f4f58e2fa83b6ea75de84440d9dc3d929
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2606
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This feature is required for boards that use a programmatical way
to reset the cpu, like the TI Pandaboard with OMAP4. The board only
has a 14 pin JTAG header that doesn't feature SRST and is reset by
direct write to the PRM_RSTCTL register.
iMX6 can be reset through triggering the on-chip watchdog, but for these
methods to work reliably, access through the AHB-AP without interaction
with the CPU core is necessary.
Change-Id: I9a07a536adda83cc2f93e504384c8c7f0306220b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3359
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tim Newsome
Tomas Vanek
Andreas Bolsch
Matthias Welwarsky
Andreas Färber
Fredrik Hederstierna
Esben Haabendal
Marc Schink
Andreas Fritiofson
Jiri Kastner
James Mastros
Aleksander Morgado
Uwe Bonnes
Salvador Arroyo
Salvador Arroyo