Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Theese devices do not have a gap in sector numbering.
The driver translates sectors numbers 12 13... to 16 17... as used on dual
bank flash devices. Therefore erase of sector 12 and above fails with error
'stm32x device protected'
on F413/423.
Drop sector number translation for devices without has_large_mem flag.
Change-Id: I65531c0dfe02e2fd0f3d68f0615e0926e9901391
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4299
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A protection block comprises two adjacent sectors in dual bank mode.
As there are 64 and 128kB sectors joined in blocks 2 and 8, block size
should be computed as a sum of sector sizes.
Change-Id: Ie915df8cf7ca232c4565d7e0c514c8933e71fdfe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4271
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
also remove legacy footnote as it adds no value.
Change-Id: I3892acf244bd8fba6f844a5d82a66004e193a395
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4309
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Extend HLA interface to allow multiple VID/PID pairs and use it to
autodetect the connected stlink version.
Change-Id: I35cd895b2260e23cf0e8fcb1fc11a78c2b99c69b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3961
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New low-end chips have only 2k of RAM, workarea size adjusted
Change-Id: Ibfccd73fef9e6dabffc87d901736c5626ce411fe
Signed-off-by: Ilia Motornyi <elijah.mot@gmail.com>
Reviewed-on: http://openocd.zylin.com/4308
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The CMSIS-DAP used by NXP's LS1012ARDB board only supports JTAG,
and not SWD. Calling cmsis_dap_cmd_DAP_SWD_Configure returns with an
error (and doesn't actually do anything in the debugger).
Wrap the call to cmsis_dap_cmd_DAP_SWD_Configure in a check for
swd_mode, to make sure initialisation doesn't fail needlessly.
Change-Id: Id7e568cb6e36886bd7c5b3699d198a77a51c28c9
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4294
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change-Id: Ieea1b0dec88818e9e8d5c8c5d54aa8959556d77b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4275
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The SWDIO buffer has to be enabled, by setting SWDIO_OE, for data on
SWDIO to reach the target. Explicitly do this before sending the
switch sequences for JTAG-to-SWD, etc.
This makes the code insensitive to the state of SWDIO_OE specified in
ftdi_layout_init. It used to work only on adapters with a non-inverted
SWDIO_OE inited to 1, or inverted SWDIO_OE inited to 0.
Change-Id: I4b9e520ac1c7ce2a437251a05fc036bc68de718e
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4270
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Similar to the Sheevaplug fix inf95f8b70fbd0f7e9c91a2d9006b1abb2dd07ebf2
the OpenRD device has its JTAG interface on the first channel of the
ft2232, which is 0 for the new driver but was 1 for the old one. Correct
the config file appropriately. Also the device description was missing
the trailing " B" and thus not picking up the device correctly. Finally
add an adapter_khz setting in the OpenRD board configuration file - set
to 2MHz to match the Sheeva variant.
Confirmed as working thanks to Phil Hands providing me access to his
hardware to test on.
See also Debian Bug#793214; https://bugs.debian.org/793214
Change-Id: Ifacf53124eaa330bbbdf36dfa79e3256bf2a5201
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4254
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The dhcsr_save variable was used to save the value of
cortex_m->dcb_dhcsr so it could be restored later. However, all writes
in between the save and the restore use mem_ap_write_atomic_u32, not
cortex_m_write_debug_halt_mask, which means cortex_m->dcb_dhcsr isn’t
changed anyway. Delete the unnecessary local.
Change-Id: I064a3134e21398e1ecfc9f1fa7efd7b020b52341
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4240
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In cortex_m_assert_reset, in two locations, DHCSR is written directly
using mem_ap_write_u32. This means that the cached version,
target_to_cm(target)->dcb_dhcsr, is not updated when these writes are
performed, so subsequent writes to DHCSR that use
cortex_m_write_debug_halt_mask will change those bits back to their old
values which, unless modified in that particular invocation, come from
the cache. This causes an actual, observable bug on an STM32F7 in which
running “reset run” immediately after “program” can in some cases result
in execution proceeding with C_MASKINTS set (it is cleared on line 1021
but is then set immediately afterward in cortex_m_clear_halt), causing
failure of the application. Replace these mem_ap_write_u32 calls with
cortex_m_write_debug_halt_mask calls to do the same jobs.
Change-Id: Id35ca7f6057c2df2ba9cd67c53a73b50816d0b71
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4239
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
GCC7 with -Wall warns about possible string truncation with
snprint()-type functions with "directive output may be truncated writing
1 byte into a region of size between 0 and 9
[-Werror=format-truncation=]" + "note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 12" (or similar). Fix this by
increasing sizes of buffers.
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Ib848f2a56dd658783534158947ae1be7c0e99d45
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4175
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
GCC7 with -Wextra warns about switch-case blocks which fallthrough with
"this statement may fall through [-Werror=implicit-fallthrough=]". This
can be fixed by adding "special" comments: "/* fallthrough */".
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Iba0be791dbdd86984489b2d9a0592bb59828da1e
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4174
Tested-by: jenkins
Add "arm semihosting_cmdline [argv0 argv1 ...]" for setting the
command line arguments for the debuggee.
[andreas.fritiofson@gmail.com]: Dynamic allocation, empty default
Change-Id: I831ddd161d602f251940e29608a154e9590fdee1
Signed-off-by: Christian Groessler <chris@groessler.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3106
Tested-by: jenkins
This config covers the 4x Cortex A53 CPUs. A custom connector
is required from J14 to standard ARM JTAG on v1 boards. However
v2 hardware should have a standard FTSH-105-01-L-DV connector.
Pinmuxing code to enable JTAG pins is included in l-loader-poplar
repository, so board is flashed with open source code, JTAG
is available at very early boot. Alternatively the following
pokes can be issued from U-Boot to enable JTAG (e.g. to debug
hisilicon SDK).
mw 0xf8a210ec 0x130;
mw 0xf8a210f0 0x130;
mw 0xf8a210f4 0x130;
mw 0xf8a210f8 0x130;
mw 0xf8a210fc 0x130;
mw 0xf8a21100 0x130;
Change-Id: I2b83dfcb3dc5461c1620f94dd99aa7b31fdda59b
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-on: http://openocd.zylin.com/4161
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Renaming of all nrf51 NOR flash code to nrf5, as to prepare the
code for being able to flash nrf51 and nrf52 chips.
The nrf51 command is retained for backwards compatability.
"nRF5" is also the name Nordic Semiconductor uses to describe
both the nrf51 and nrf52 chips.
Change-Id: I5f4e3f1ec780184b28ad44f735a746e68908c502
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4209
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This cleans up the list of supported nrf51 chips considerably.
Change-Id: Ic74685657bb72a8703c0a49df4c48c54604ec2a7
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4208
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Trying to read the L0 idcode at the L1 idcode address 0xE0042000 often
resulted in an uncatched error. Reading at the right L0 address 0x40015800
afterwards results in reading 0. So access to the device is denied..
Change-Id: I6de92cf99a5d5d46c72f9ba055613cbc5753a951
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3883
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
in some cases we need something to test if uart is actually
properly connected.
Change-Id: I5a16b053164b34bb30ae8370753be12887a85c51
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Finally we can use this driver by default!
Change-Id: I09d215d1bd1dc16873a7379637e6869af65ad8f1
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4193
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Make this error message more useful by providing the port number
that we tried to bind to.
Change-Id: Ieb18adf0725a6ae99c77ebfaadc49d64ed407bbe
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-on: http://openocd.zylin.com/4157
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
TDO and TMS: Safest values given it's an evaluation board
and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
high impedance (tri-stated).
Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for Blue Gecko and Mighty Gecko chips from
Silabs.
They have different EFM32_MSC_REGBASE and LOCK register offset.
Based on the original patch from Andreas Kemnade.
Change-Id: I166c14960ced7c880b68083badd1b31372fefabe
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-on: http://openocd.zylin.com/4034
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: chrysn <chrysn@fsfe.org>
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.
See also Debian Bug#837989; https://bugs.debian.org/837989
Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Use unsigned constant for left shift operation in order to avoid the
following error with GCC >= 6.0:
../src/flash/nor/stm32f2x.c: In function ‘stm32x_handle_unlock_command’:
../src/flash/nor/stm32f2x.c:1324:67: error: left shift of negative value [-Werror=shift-negative-value]
stm32x_info->option_bytes.optcr2_pcrop = OPTCR2_PCROP_RDP | (~1 << bank->num_sectors);
Change-Id: I0ac082bd0dbb8dc2f61ffff8fdf486ab7962d2e0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4207
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Anton Fosselius <anton.fosselius@gmail.com>
Reviewed-by: Esben Haabendal <esbenhaabendal@gmail.com>
If no serial number is specified, disable TCP/IP device discovery to
ensure that a user does not unintentionally operate on a remote device.
Change-Id: I6a7e913b8b679fae003825468cd86d2014849b29
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4214
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If multiple devices are attached, do not automatically use the first
device found. Otherwise, a user may unintentionally operate on the
wrong device.
Change-Id: I08c4110b82e911e9e3e744d41830ffc6c56c44bf
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4213
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use a human-readable error description rather than just the error name
in log messages.
Change-Id: Iab4ff7a7e4d9993983a07eab9f462820d4ee8190
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4212
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
libusb is now optional for libjaylink because support for TCP/IP
devices is always available.
Change-Id: I03f2566f8e1703276671ac0f353f72394d21f2f0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4204
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Update to latest Git version and bump required libjaylink package
version to 0.2.0.
This version introduces support for devices with TCP/IP interface (e.g.
SEGGER Flasher ARM) and an additional debug level for I/O messages.
Change-Id: I030236aa704a91d1bb1843dd30010865947747e0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4202
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Jiri Kastner
Tomas Vanek
Spencer Oliver
Paul Fertser
elmot
Ake Rehnman
Alexandre Torgue
Bas Vermeulen
Robert Jordens
Marc Schink
Jonas Norling
Jonathan McDowell
Christopher Head
Freddie Chopin
Andreas Fritiofson
Tim Newsome
Peter Griffin
Slowcoder
Uwe Bonnes
Oleksij Rempel
Robert Foss
Diego Herranz
Andrea Merello
Fabio Utzig