Commit Graph

225 Commits

Author SHA1 Message Date
Paul Fertser 24099b4c14 board: add TM4C123G LaunchPad config
Almost the same as the LM4F120 LaunchPad but the chip is using the new
naming scheme (Tiva C series), supports USB OTG and has some new PWM
hardware blocks.

Change-Id: I6a7b2df76768766471f366cddaf64df3cc63f5f2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1647
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-10-03 09:26:08 +00:00
Franck Jullien 4e79b48e2c Add new target type: OpenRISC
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.

Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2013-09-26 09:52:56 +00:00
Brad Riensche 02826721d0 Add tcl configurations for Altera Soc devices
This commit adds two tcl configuration files, one for the Altera
Cyclone V SoC series, and one for the SoCkit development board.
The board configuration is able to halt and resume the cpu cores,
and dump register contents etc.  It has not been fully tested, however.

Change-Id: Id3f18c3408975cf986a5f5aec410b5b13240c35e
Signed-off-by: Brad Riensche <brad.riensche@gmail.com>
Reviewed-on: http://openocd.zylin.com/1494
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-08-15 14:50:22 +00:00
Marek Vasut e608ced330 ftdi/board: Add support for DENX M53EVK
Add support for DENX M53EVK board and it's integrated on-board
JTAG adapter using FT2232H.

Change-Id: I022dcafa7799bb84a7873ba67ed82f1e49094320
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1461
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2013-07-15 10:02:37 +00:00
Marek Vasut 7ccc511088 target: Pull out the jtag_rtck from iMX5x files
Pull the jtag_rtck setting from imx51.cfg and imx53.cfg . Since
not all boards using these CPUs do support RTCK signal, move the
configuration of RTCK into board files.

Change-Id: I632c5d38e00ada8779a451cd26428fd122452001
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1460
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2013-07-15 10:02:32 +00:00
Hsiangkai Wang cf8a3c3d70 nds32: add new target type nds32_v2, nds32_v3, nds32_v3m
Add target code for Andes targets.

Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2013-06-05 19:27:35 +00:00
Spencer Oliver d9ba56c295 target: rename cortex_a8 to cortex_a
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.

cfg files have also been updated to the new target name.

Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2013-04-28 08:56:04 +00:00
Spencer Oliver 1fd8ac0ee6 cfg: add Netgear DG834v3 configuration
Change-Id: I3f4880d8b07b9623544b94d316b37e6d0ae97020
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1189
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2013-03-06 21:57:29 +00:00
Spencer Oliver 80649fc3d5 cfg: increase stm32l-discovery working area
This part has 16k ram so make it all available.

Change-Id: Ifeb7bc850bfe4f68d0affb8f6a0931b4327e7257
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1006
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2012-12-30 11:35:16 +00:00
Spencer Oliver adb8ec32dc icdi: add TI icdi interface
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.

Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
2012-12-23 21:46:20 +00:00
Gianluca Renzi 051ec13abc Generic LPC1850 board w/ SPIFI flash.
This config file is intended as an example of how to
use the lpcspifi flash driver, but it should be functional
for most LPC1850 boards utilizing SPIFI flash.

Change-Id: I855854282336701fd210134497ce014017f3aaec
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-11-06 14:34:16 +00:00
Spencer Oliver 8cbcd56c0e cfg: update ti/stellaris url's
Change-Id: I96f17c5ea2be506a6b88434616ca52c3e392868a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/879
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02 21:59:48 +00:00
Spencer Oliver ebece4a981 cfg: add ti ek-lm3s9d92 config
Change-Id: Ib09ca3e57de363a24d704b184ba8546bad08f56f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/853
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02 11:34:54 +00:00
Spencer Oliver a046475f03 cfg: add ti ek-lm3s8962 config
Change-Id: I753cec80a904130088b00b3f81b6dd61808662d6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/852
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-10-02 11:34:41 +00:00
Spencer Oliver 2076ba093d cfg: add STM32F3-DISCOVERY board support
Change-Id: I4a02e0504fc04ffc1238d9bb77ec05c1f781e7e8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/810
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
2012-10-02 11:27:59 +00:00
George Harris 516719b6b8 Added SPIFI flash driver, algorithms, and docs
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.

Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-09-26 16:17:42 +00:00
Joerg Fischer 8fe2bed92c cfg: Add Hitex LPC1768-Stick using ftdi driver
Add cfg files for Hitex LPC1768 Stick
Website: http://www.hitex.com/?id=1602

This board has a FTDI2232D as JTAG interface, using the
same layout as the Hitex STM32-PerformanceStick but with
different USB PID.

Main MCU is a LPC1768 from NXP.

The interface config uses the ftdi driver instead of ft2232.
The corresponding ft2232 layout would be "stm32stick".

Change-Id: I1fd15588c5af35f7d51777d1ad958cc1dc72c6f7
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/763
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-08-01 21:12:27 +00:00
Tom Rini 5e4ee571cc board: Add TI AM335x Evaluation Module
This patch adds the TI AM335x Evaluation Module (ti_am335xevm) board
configuration file.

Change-Id: Id3529e54972f8acd8c790ad55c8d0f4058a1a1f6
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/753
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
2012-07-19 18:48:06 +00:00
Christopher Kilgour aeb3c4f37e kinetis: update support for all program flash granularities
Updates the Kinetis NOR flash support to handle all known block and sector
sizes.  Previously only 2kiB sectors were hard-coded, now all four known
combinations non-volatile sector sizes are supported.

The premise of separating Kinetis Program Flash (PFLASH) from FlexNVM is
also introduced.  This means each "block" of flash (in Freescale terms) is
treated as a bank in OpenOCD.  Correspondingly, the existing board
configuration for the TWR-K60M512 eval system is updated to recognize two
banks instead of one.

A board config for the TWR-K60F120M is also added.

Bank and sector erase and programming has been checked with both of the
mentioned eval boards.

Change-Id: Iae2d10ebf8f548d0a3698df5430bbbe1ccadc58a
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/663
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-06-26 11:53:37 +00:00
Mathias K 423bfc49f9 board: Add Sony Ericsson J100I Phone
This patch add the Sony Ericsson J100I Phone to the board configurations.

Change-Id: I083ddf067c8ecdfdda0404fe9e9df980dbb86fe8
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/631
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-05-25 12:06:41 +00:00
Freddie Chopin caeb057205 Use hardware reset and connect under reset on boards with ST-LINK/V2, as
now it is supported.

Change-Id: Id3b2ca9a2270974a5f453323f9057ecece400c94
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-05-14 09:32:20 +00:00
Spencer Oliver a09bb27e23 cfg: add stm320518-eval onboard stlink config
Change-Id: Ie92a87ce077c538fdd04af37c798e0a8054b423a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/610
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
2012-05-14 09:32:03 +00:00
Spencer Oliver 7fca524606 cfg: increase stm32f0discovery board working area
Change-Id: Iea166ee27fc60bbfdeb851fdcf71509f3984f72f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/602
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-05-08 14:05:45 +00:00
Bill Traynor 388d041e0f cfg: add default pid/vid pair to beaglebone board cfg.
The newer versions of BeagleBone boards use the default vid/pid
pair for FT2232 debugging.  Please see the following README:
http://beagleboard.org/static/beaglebone/latest/README.htm
On revision A3/A4 boards, the VID/PID were chosen to match the
 TI XDS100v2 (0x0403/0xA6D0). On A5 and newer revisions when we've
 given the authors of CCS the chance to update their software, the
generic FTDI VID/PID (0x0403/0x6010) will be used to simplify
installation of drivers for systems already having those drivers.

Change-Id: I44228eb2029162f23d084eb05bcfef39e615668d
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/619
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
2012-05-07 19:58:15 +00:00
Spencer Oliver ee38fff78b cfg: fix incorrect stm32vldiscovery working area
The working area used in the config was incorrect, we only have 8K on this
board not 16K as the original cfg was declaring.

Change-Id: Ie0309fb86d839bd3bc1ac9383905b581fac5c388
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/598
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2012-04-30 13:06:34 +00:00
Olivier Schonken d1cd97777b topic: Added support for the SAM4S variants
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48

The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.

Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used.  The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.

Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.

Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-04-26 10:58:14 +00:00
Uwe Hermann 28e43783e5 Split olimex_stm32_h107.cfg.
Use one board file per eval board, so that the filename matches the
exact board the user has / wants to use. Merging different boards into
one file is confusing.

Change-Id: I7c50233924a87a913723d7215c4851039c2971bc
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/566
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-04-20 15:33:24 +00:00
David Anders 43d4ae4763 pandaboard: add initial TCL support for pandaboard-es
add initial TCL support for the pandaboard-es which is
based on the omap4460 from Texas Instruments.

Change-Id: Ic63588721487feb95e7cb3d41cfaab0d2f181766
Signed-off-by: David Anders <danders.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/573
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
2012-04-18 20:32:08 +00:00
Spencer Oliver 7e2fb7ce9a cfg: add stm32f0discovery board config
Change-Id: I4fccdbd4e0a3bc70cd425c910ad1007519098e20
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/570
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
2012-04-18 10:50:16 +00:00
Uwe Hermann b6068f5a48 Glyn Tonga2: Faster JTAG speed after CPU/RAM init.
Change-Id: Ib08dae0035355138c468483a7ee2d73aadedf430
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/564
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-04-13 08:57:29 +00:00
Wjatscheslaw Stoljarski (Slawa) 108a458ab8 cfg: add icnova_imx53_sodimm board config
Add board config for In-Circuit ICnova iMX53 SODIMM

Change-Id: I3802ab1695baa75c1f170cf1af0e38ada284c0b8
Signed-off-by: Wjatscheslaw Stoljarski (Slawa) <wjatscheslaw.stoljarski@kiwigrid.com>
Reviewed-on: http://openocd.zylin.com/543
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-04-10 12:25:52 +00:00
Wjatscheslaw Stoljarski (Slawa) e3b3273433 cfg: add imx53loco board config
Add board config for iMX53QSB (loco)

Change-Id: I8659dcd71a56d5fe855eaf62be0a415198b558c5
Signed-off-by: Wjatscheslaw Stoljarski (Slawa) <wjatscheslaw.stoljarski@kiwigrid.com>
Reviewed-on: http://openocd.zylin.com/542
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-04-10 12:24:00 +00:00
Simon Widmer fad7240689 Support for KaRo TX25 CPU Module on a StarterkitV base board
This patch adds support for the KaRo TX25 module on a StarterkitV base board.
For board details, check http://www.karo-electronics.com/tx25.html

Change-Id: I2c80c5467bc476955b55196728aa3c37c8185e6c
Author: Simon Widmer <simonxwidmer@gmail.com>
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Reviewed-on: http://openocd.zylin.com/557
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-04-10 12:15:16 +00:00
Uwe Hermann 1748aab2c9 Initial config for the Voltcraft DSO-3062C.
This is a digital oscilloscope which uses a Samsung S3C2440 internally.

http://randomprojects.org/wiki/Voltcraft_DSO-3062C

Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Change-Id: I5e28c3a8f30665a162e34c831294e4e658a16ebb
Reviewed-on: http://openocd.zylin.com/548
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
2012-04-02 00:02:56 +00:00
Spencer Oliver 067ac78b61 cfg: add support for STM3220G-EVAL onboard STLINK
Change-Id: Icd7a1baf6f2623e5b57d29c4602a2762af730936
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/541
Tested-by: jenkins
2012-03-30 16:02:36 +00:00
Spencer Oliver e9976aa3a8 cfg: add STM32F4x and STM3241G-EVAL config files
This adds support for the STM32F4 target and the STM3241G Eval Board, in
both standalone and using the onboard STLINK.

Change-Id: I62f8908b5880568b2b36c78a78f94c40861ff335
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/540
Tested-by: jenkins
2012-03-30 16:02:14 +00:00
Spencer Oliver 4e31b87943 scripts: use adapter_nsrst_delay not deprecated jtag_nsrst_delay
Change-Id: Idf98526d64dcba4d8a5b6910bd3c539756753e8e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/539
Tested-by: jenkins
2012-03-30 16:01:51 +00:00
Olivier Schonken 90d33c5c87 Added tcl config scripts for SAM3A/X targets and devboard
The SAM3A/X processors that were released thus far is either
a SAM3A/X(4) - 256K, or a SAM3A/X(8) - 512K device.  Thus
the config files are per variant, and not per device.

Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>

Change-Id: I84d26d044e810eb428b1d6287907ea3bf8364c73
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/522
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-03-30 15:56:19 +00:00
Chris Morgan 8fc35a696f Create a init_board procedure for the ea dev board.
Signed-off-by: Chris Morgan <chmorgan@gmail.com>
Change-Id: I082b0d3092c7f3b2ee6b68af64d48c78b31f1dbf
Reviewed-on: http://openocd.zylin.com/510
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-03-30 15:53:06 +00:00
Jan Dakinevich 34d1f82c75 jtag: basic support for P&E Micro OSBDM (aka OSJTAG) adapter
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.

Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-03-13 17:04:07 +00:00
Øyvind Harboe ed12a6521f flash: retire unused eCos flash driver
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.

Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
2012-03-11 21:14:21 +00:00
Jim Norris 0ab3f83667 Add new configuration files for the Diolan LPC-4350-DB1 development
board with the NXP LPC4350 processor.

Change-Id: I0843e96af9ca05d3e598e2e16eb19fc0581ab46d
Signed-off-by: Jim Norris <u17263@att.net>
Reviewed-on: http://openocd.zylin.com/501
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-03-06 13:31:59 +00:00
Neil Jensen 21a0f9b48b cfg: Beaglebone/AM335x refactor
Split out functions specific to the AM335x SOC into the target directory and simplified the board config
file.  This should allow one to quickly create new configs for boards based on the TI processor family.

Change-Id: I0c3db97950dfa832f1f1918fc10c180f068bba74
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-02-27 10:01:44 +00:00
Neil Jensen 3a7ca6a621 cfg: beaglebone cleanup
Simplified the configuration and removed things that were not necessary for debugging.  Also added reset
configuration.

Signed-off-by: Neil Jensen <neil30al@gmail.com>
Change-Id: I96f991c3051aa68278212cd6509484cbce40ccb7
Reviewed-on: http://openocd.zylin.com/488
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-02-27 10:01:01 +00:00
Neil Jensen dec6b91380 cfg: beaglebone
Moved ti_beaglebone.cfg to the board configuration directory.  This was
originally placed in the wrong location.

Signed-off-by: Neil Jensen <neil30al@gmail.com>
Change-Id: I05d10b62b1a21618635ee1773c30d77dc756ec82
Reviewed-on: http://openocd.zylin.com/481
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-02-24 09:11:49 +00:00
Spencer Oliver fd39a5e8ad cfg: change default stellaris working area
This sets the default stellaris working area to 2k rather than
the current 8k. 2K is the smallest RAM size in the stellaris family.

Change-Id: I1407f758eb0926cc094b824a6d25199b313c45de
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/458
Tested-by: jenkins
2012-02-16 08:57:22 +00:00
Lars Poeschel 87bf0db125 add icnova_sam9g45_sodimm support
This adds support for in-circuit icnova sam9g45 sodimm: http://www.ic-board.de/product_info.php?info=p214_ICnova-SAM9G45-SODIMM.html|ICnova
The NAND flash is not yet working.

Change-Id: I94ca5203f8d8a55dec1e4e87cd0631bd2b8393f9
Signed-off-by: lars@kiwigrid.com
Reviewed-on: http://openocd.zylin.com/418
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-02-13 12:04:00 +00:00
James Robinson 5d43ffd5bc topic: Add support for i.MX28EVK
Added the file imx28.cfg to the target directory
Added the file imx28evk.cfg to the board directory

Change-Id: I02a74a03f3773892f830d13660ffdded34f3261d
Signed-off-by: James Robinson <jmr13031@gmail.com>
Reviewed-on: http://openocd.zylin.com/428
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2012-02-13 12:03:26 +00:00
Spencer Oliver 5bcb78f181 cfg: add revb ek-lm3s811 board config
Add board config for older (revb) ek-lm3s811

Change-Id: I75aca1714de3e88b60d00fa0f99f2c4b076b569c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/444
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
2012-02-10 16:59:06 +00:00
Spencer Oliver 19edcec872 cfg: add stm32ldiscovery board config
Change-Id: I392fdc4c588783fda1c7d4d6413b86ae9aa3f6b9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/442
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
2012-02-10 14:23:45 +00:00