- ETB
* report _actual_ hardware status, not just expected status
* add a missing diagnostic on a potential ETB setup error
* prefix any diagnostics with "ETB"
- ETM
* make "etm status" show ETM hardware status too, instead of
just traceport status (which previously was fake, sigh)
- Docs
* flesh out "etm tracemode" docs a bit
* clarify "etm status" ... previously it was traceport status
* explain "etm trigger_percent" as a *traceport* option
ETM+ETB tracing still isn't behaving, but now I can see that part of
the reason is that the ETB turns itself off almost immediately after
being enabled, and before collecting any data.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2790 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Improve and clarify the wording of the introduction.
- Add section on version taggging.
- Some other minor corrections.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2788 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The release process itself does not use this support yet, but it allows
packagers to automate the process of managing their own tags, if they
patch the source code before releasing binaries. The release processes
should be revised to incorporate this feature to support -rc packages.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2786 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- The NEWS step failed due to an empty commit comment.
- The final release step would have failed, because the steps to switch
from the secure to insecure repository (and back again) require both
switch and a URL relocation steps
git-svn-id: svn://svn.berlios.de/openocd/trunk@2782 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Don't issue needless JTAG resets ... only do them after
errors. Normal exit now leaves every TAP in BYPASS.
- Fix an unlikely memory leak on one fault path.
- Remove the oddball limitation that invalid capture LSBs
trigger errors only for TAPs that support IDCODE.
Re the JTAG reset: there are too many of them, and they can
(and do!) change system state. So the needless ones should
get removed. This one was especially pointless.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2777 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Commands were supposed to have been "arm11 memwrite ..."
not "memwrite ..."
- Get rid of obfuscatory macros
- Re-alphabetize
- Add docs for "arm11 vcr"
git-svn-id: svn://svn.berlios.de/openocd/trunk@2776 b42882b7-edfa-0310-969c-e2dbd0fdcd60
When the OpenOCD server starts up it records its state as TAP_RESET,
even though it could be anything. Then when it starts to examine
the scan chain, it calls jtag_add_tlr() which sees it doesn't have
any work to do, and so it does nothing. This can make the next
operations fail because they start from the wrong TAP state...
Instead of caring about the current recorded state, always enter
TAP_RESET by forcing five clocks with TMS high.
(NOTE: it seems most other JTAG adapter drivers have this same bug.)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2763 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Change the handling of the "-ircapture" and "-irmask" parameters
to be slightly more sensible, given that the JTAG spec describes
what is required, and that we already require that conformance in
one place. IR scan returns some bitstring with LSBs "01".
- First, provide and use default values that satisfy the IEEE spec.
Existing TAP configs will override the defaults, but those parms
are no longer required.
- Second, warn if any TAP gets set up to violate the JTAG spec.
It's likely a bug, but maybe not; else this should be an error.
Improve the related diagnostics to say which TAP is affected.
And associated minor fixes/cleanups to comments and diagnostics.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2758 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Ready for discussion and tiny patches that tries out this scheme.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2755 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Added gdb_sync feature that allows GDB to sync up to target state.
Issue "monitor gdb_sync" and the next stepi, will return immediately
with updated register values to GDB.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2754 b42882b7-edfa-0310-969c-e2dbd0fdcd60
make sure that when there are two or more targets, their
various pre/post event reports are correctly ordered.
Previously, only the first target always saw its "pre"
method before SRST was asserted or deasserted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2753 b42882b7-edfa-0310-969c-e2dbd0fdcd60
only expose the registers which are actually present. They
could be missing for two basic reasons:
- This version might not support them at all; e.g. ETMv1.1
doesn't have some control/status registers. (My sample of
ARM9 boards shows all with ETMv1.3 support, FWIW.)
- The configuration on this chip may not populate as many
registers as possible; e.g. only two data value comparators
instead of eight.
Includes a bugfix in the "etm info" command: only one of the
two registers is missing on older silicon, so show the first
one before bailing.
Update ETM usage docs to explain that those registers need to be
written to configure what is traced, and that some ETM configs
are not yet handled. Also, give some examples of the kinds of
constrained trace which could be arranged.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2752 b42882b7-edfa-0310-969c-e2dbd0fdcd60
system, removes 20 non-existent registers ... but still includes
over 45 (!) ETM registers which don't even exist there ...
- Integrate the various tables to get one struct per register
- Get rid of needless per-register dynamic allocation
- Double check list of registers:
* Remove sixteen (!) non-registers for data comparators
* Remove four registers that imply newer ETM than we support
* Change some names to match current architecture specs
- Handle more register info
* some are write-only
* some are read-only
* record which versions have them, just in case
- Reorganize the registers to facilitate removing the extras
* group e.g. comparator/counter #N registers together
* add and use lookup-by-ID
git-svn-id: svn://svn.berlios.de/openocd/trunk@2751 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Add a header comment
- Line up the ETM context struct, pack it a bit
- Remove unused context_id (this doesn't support ETMv2 yet)
- Make most functions static
- Remove unused string table and other needless lines of code
- Correct "tracemode" helptext
Also provide and use an etm_reg_lookup() to find entries in the ETM
register cache. This will help cope with corrected contents of that
cache, which doesn't include entires for non-existent registers.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2750 b42882b7-edfa-0310-969c-e2dbd0fdcd60
didn't turn up earlier. Is everyone still using gcc 3.x? Or is the x86
version of gcc 4.x much more relaxed?
git-svn-id: svn://svn.berlios.de/openocd/trunk@2749 b42882b7-edfa-0310-969c-e2dbd0fdcd60
of a (NOR) flash chip: allow passing "last" as an alias
for the number of the last sector.
Improve several aspects of error checking while we're at it.
From: Johnny Halfmoon <jhalfmoon@milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2746 b42882b7-edfa-0310-969c-e2dbd0fdcd60
mlu
dbrownell
zwelch
oharboe
ntfreak