instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In flash/nor/cfi.c:835 struct cfi_info is allocated by malloc(). As
write-mem was uninitialized the pointer pointed to an out of range
address, which led to a segmentation fault and crashed openocd.
This happened during flash-command of an external flash-bank, using
cfi.
Use calloc() instead.
While on it check for NULL return and remove unnecessary initialzation.
Change-Id: I0e2ffb90559afe7f090837023428dcc06b2e29f6
Signed-off-by: Mischa Studer <mischa.studer@csa.ch>
Reviewed-on: http://openocd.zylin.com/6070
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 4c00f96fc2 ("configure.ac: switch to autoconf 2.69")
changes the required minor version of autoconf.
Update the README file accordingly.
Change-Id: I98b32b888ff531300f03c4ef9ebcbf8110509e52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6114
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
In case of some error, the USB device and firmware file are still
claimed. Make sure refcounting is properly accounted for both cases.
Change-Id: I933114f68e59280e58372c0941a0062fe96ab340
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/6115
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If not, multiple instances of OOCD can concurrently use it.
Change-Id: I48cc9d90521d1dcc7720c6e8bec74f45972d16f7
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4589
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For Zephyr rtos support it is necessary to define general register
numbers for architecture. There were some already in arc.h file.
Let's define ARC registers numbers as a set instead of separate defines.
Change-Id: I63742b8608f9556c2ec9bd2661a0fd9cf88e9b74
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/6105
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This removes some warnings which prevent a successful build with -Werror
which is enabled by default. I'm using gcc 11, so maybe others are not
getting this warnings yet.
In src/flash/nor/numicro.c the debug messages were misleadingly indented.
In src/target/arm920t.c the array size where smaller than expected from
the receiving function.
Change-Id: I66f5c6a63beb9f9416e73b726299297476c884d8
Signed-off-by: Rene Kita <git@rkta.de>
Reviewed-on: http://openocd.zylin.com/6104
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this will help navigate to the line start and end easily
Change-Id: I3f42eb5267df64c59a85ece67de5fce39a8843ec
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6094
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Support halting the CPU directly after a reset. If halt is
requested, the CPU stops directly at the reset vector, before
any code is executed.
This functionality was implemented using the Reset Catch
debug event.
Change-Id: If90d54c088442340376f0b588ba10267ea8e7327
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/5947
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
With zy1000 removed, there is no other implementation that uses
the minidriver, apart from the test/example minidriver-dummy.
While the idea of the minidriver is probably still valid (that is
to intercept jtag primitives before serialization), there is no
current use case, no guarantee it is really working, and the way
it was implemented (by macros and #if conditionals) is really hard
to maintain and test.
Let's let it rip in git history, from where it could eventually be
taken back in a more modern implementation.
The entry points of minidriver API are still in the code with the
original names.
Change-Id: I882e32cb26cf5842f9cba14e3badaf8948e3760d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6091
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The code for ioutil has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I36dce1669ebe9acada5f9e752835c53e5214e3be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6089
Tested-by: jenkins
The code for oocd_trace has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I989f8345dee4ff2369bcf5e2e2ace86bbd5aa6a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6088
Tested-by: jenkins
We do not have anymore any deprecated target name.
Drop the code to handle deprecated target names and the placehold
in struct target_type.
This patch is separated from the patch that drops the remaining
deprecated target names to be ready to revert this if there is any
need in the future.
Change-Id: I96fca7ffa39d8292f81e79f115ea45c4a30035d7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6087
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some target name were marked as deprecated in release v0.7.0 and
v0.8.0, almost 7 years ago, and replaced with more 'actual' names.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.8.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the target names already deprecated in v0.8.0.
Change-Id: I7c7491496db1b302b4eb1e9fc6090b58d4acf05a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6086
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OpenOCD command line flag -p/--pipe was marked as deprecated
in release v0.5.0, more than 9 years ago.
We can reasonably expect that in these 9 years any user of OpenOCD
has already migrated to v0.5.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the command line flag already deprecated in v0.5.0.
Change-Id: I2faeb592ed2c2f67c2d3227f118093e39fcf4a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6084
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm920t cp15i' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I755c4283e13e125558fcd73b15fe20498eae95ca
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6083
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm720t cp15' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I2b325d0312d96ca5e5f0f1bad13bb162b3b75c52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6082
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is specially needed when, in the probe routine, device is not
found among the stm32l4_parts. In this case, the stm32l4_flash_bank->part_info
is undefined and inadvertentanly used afterwards:
part_info = stm32l4_info->part_info;
If the stm32l4_flash_bank is zero init, the probe routine checks for
the validity of the part_info field in the previous struct and correctly
detects the unsupported (or not found) condition, raising an error
rather than a SIGSEGV
Change-Id: I7d9d669fb3fa7f8f0903acd60046966b4acb0031
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6103
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
OpenOCD file configure.ac requires autoconf equal or newer then
2.64, which is quite old.
These are the release dates so far:
- autoconf-2.64 2009-07-26
- autoconf-2.65 2009-11-21
- autoconf-2.66 2010-07-02
- autoconf-2.67 2010-08-02
- autoconf-2.68 2010-09-22
- autoconf-2.69 2012-04-24
- autoconf-2.70 2020-12-08
Switch to autoconf 2.69, which is old enough to be the standard in
current systems.
This should reduce the effort on configure.ac compatibility.
Change-Id: Ia7c78d2fa34c50ed5ccf4fb66ad3484369cf3b4a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6008
Tested-by: jenkins
Update jimtcl to version 0.80.
Add a workaround in Makefile.am to allow 'make distcheck' with the
new jimtcl. A fix is already merged upstream but will be part of
the future release 0.81 of jimtcl.
Change-Id: I1cebfb9c17179114960dc771e0b31836b4b9b058
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5949
Tested-by: jenkins
The Broadcom BCM2711 used in Raspberry Pi 4
No documentation was found on Broadcom website
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711/
Change-Id: I3db6c9af520af8ab4c21ad35ff0f2db28efc0325
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6066
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Broadcom chip used in the Raspberry Pi 2 Model B
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2836
Change-Id: I50b040db213c5b72f63d5f5534c552426c7376f9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6068
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the Broadcom chip used in the Raspberry Pi Model A, B, B+,
the Compute Module, and the Raspberry Pi Zero.
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2835
Change-Id: Ifeb012952473d624327e8c010ac5c886d9473aa0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6067
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There is no good reason to use macros instead of static inline functions. The
current code is hard maintain. For example, it changes variables outside of the
macro scope. Also, it is conflicting with the C coding style.
Change-Id: I5ac9d2ae076ef73c176d4e32b2e7e0a99fa875ab
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6046
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The buffer passed to stlink_usb_trace_read() is allocated of size
*size and does not need to be zero-terminated. There is no reason
to not fill its last byte.
When checking the bytes available on swo, limit the retrieved byte
length to *size.
Change-Id: Iade0f8963118695931f13a8a3f1ab204911236b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6061
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Missing the space cause the hex value to be printed together with
the following field.
Add a space after PRIx32.
Change-Id: I95824a9a8b8c0ad911d6c31f732d926cb3e0c068
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6060
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
With the removal of old tpiu code, commit 7e6556b3ca ("server:
permit the add_service function to return the created service")
http://openocd.zylin.com/5717/ can be reverted.
Fix also the new calls to add_service().
Change-Id: Ib7f2dfc6a9e829239e20313e0f121911085fdc00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6031
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Create the TPIU and SWO device in target config file.
Replace the target event 'trace-config' with the TPIU/SWO event
'post-enable'.
Extend the existing code in the event handler to properly set the
gpio mode and speed to permit synchronous trace.
This patch is not exhaustive of all the targets that have SWO, but
has to be considered as an initial example.
Change-Id: If4bbf364c0d2aef3ae49951e76507a3b1cfd58e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5859
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
This is supposed to replace big part of armv7m_trace.[ch], since
TPIU is not only the one implemented in Cortex-M3 and M4.
Change-Id: I7588d16cbefe9cdb371c52fb0aa5cdfb48518804
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5858
Tested-by: jenkins
If the command 'itm port[s]' is issued before 'init', the ITM can
not be programmed because OpenOCD cannot access the target yet.
The configuration is recorded and applied after target examine.
The current test to trigger the ITM delayed-programming is based
on the TPIU configuration. This is allowed because the only use of
ITM it so send data through TPIU.
In case of system TPIU, not belonging anymore to the target, there
is no more association between target ITM and system TPIU.
Add a flag to record the pending ITM configuration requested
before 'init' and test the flag to trigger the delayed-programming
of the ITM.
Change-Id: I101eb97a116d7925cd2ff068f3e8813fc008b08e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6029
Tested-by: jenkins
The change [1] guarantees that the value pointed by 'prescaler'
gets always set, even when the adapter does not support the
specific mode requested (e.g. sync), or during trace disabling.
This works fine with the code in armv7m_trace_tpiu_config(), but
requires all the parameters to be valid also to disable the trace
(with 'enable==false'), otherwise returns error on incorrect
parameters or even causes segmentation fault if pointers
'trace_freq' or 'prescaler' are NULL.
Another problem in stlink_config_trace(), not linked with [1], is
caused by a tentative to change the settings on an already enabled
trace; the trace is disabled before the new parameters are fully
validated and in case of invalid parameters the trace is not
re-enabled.
It would be more logical to first check all the parameters, then
disable the trace, change the settings and re-enable the trace.
Practically revert [1] by checking 'enable==false' at function
entry, then disable trace and exit without any further check on
the other parameters.
For the case 'enable==true', validate all the function parameters
then disable the trace, update the trace settings and re-enable
the trace.
Modify the caller armv7m_trace_tpiu_config() to initialize the
variable 'prescaler' to a safe value to avoid the issue targeted
by [1].
[1] commit 38277fa752 ("jtag/drivers/stlink_usb: fix SWO prescaler")
Change-Id: Ia6530682162ca2c9f5ac64301f2456f70cc07ed2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5934
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Convert the driver from libusb0 to libusb1.
Change-Id: I17d14522db18b4050d462d23151ec97d3a315a7f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5991
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
pg315 of CoreSight Components:
It is recommended that the ITMEn bit is cleared and waits for the
ITMBusy bit to be cleared, before changing any fields in the
Control Register, otherwise the behavior can be unpredictable.
Change-Id: Ie9a2b842825c98ee5edc9a35776320c668047769
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6043
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target->endianness is initialized to TARGET_ENDIAN_UNKNOWN at 34 lines
below, before calling target_configure. This initialization is
redundant and not needed.
Change-Id: Iea2d5e17a13c1a8b0b209ba7c20043736b520ef6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The C style guide forbids typedef'd structs, see 'Naming Rules'.
Change-Id: I983dd52307136d1b5adb58d8c44c0c14422d31e2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6032
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tarek BOCHKATI
Tomas Vanek
Mischa Studer
Andrew Wesie
Antonio Borneo
Oleksij Rempel
Evgeniy Didin
Rene Kita
Tim Newsome
Christian Hoff
Raúl Sanchez Siles
Marc Schink
Felipe Balbi
Adrian Negreanu
Yasushi SHOJI