Starting from version 8, gcc issues a warning if strncpy could be
able to truncate a string (so without adding the zero-termination
char in destination) by copying exactly "size" char from a source
string not shorter than "size".
Such truncation from strncpy could actually be the desired code
behaviour, but the way to silent gcc only locally (without global
disabling with -Wno-stringop-truncation) through pragma has other
side effects on portability.
In current code, the source string is always "eth0", because has
been checked right above. So this is a false positive from gcc,
being always strlen("eth0") < 16, the sizeof(ifreq.ifr_name).
Silent gcc by decrementing the "size" and remove:
error: ‘strncpy’ specified bound 16 equals destination
size [-Werror=stringop-truncation]
This file is only optionally compiled together with ZY1000 driver
with --enable-zy1000 --enable-ioutil. This combination is not
checked in jenkins, so the error passed unnoticed.
Plus, the configure flags above are both deprecated!
Change-Id: I229e66227cfd3513139feeaffa47a6e1ec00767b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5631
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The commands "ocd_find" and "capture" are registered directly
through the jim API, instead of the common way to describe them
in a struct command_registration that is then passed to the helper
register_commands().
This cause the two commands above to not have either "help" nor
"usage" string nor a properly identified "mode".
Since the following line registers the commands listed in struct
command_builtin_handlers, simply add the two commands above in the
same struct.
Change-Id: Id6ee11dac3b18364deeed65ee8e18ad80152750a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5644
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The state machine of cortex-m have to pass through a set of state
before it get in "halted".
Add one more "arp_poll" to achieve the proper state during a
"reset halt" command in engineering boot.
Change-Id: I90828bf20ef75bd4018f8b911f727ae69c4d6e8f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5649
Tested-by: jenkins
Reviewed-by: Richard Braun <rbraun@sceen.net>
Restore the prompt after the "history" command is invoked.
Change-Id: I3d0744abbc58e82b039e06f21675efa180e8e1b0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3414
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this patch we introduce set/unset breakpoints
routines and add/remove bp handlers.
Currently soft breakpoints are only supported.
Changes since v1:
* Change if-statement in arc_remove_breakpoint
* Squash changes from http://openocd.zylin.com/#/c/5641/
in this commit to fix build.
Change-Id: Ib10ccdb02fd1606e4f407f012b1bee106a8ffccd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5641
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This commit introduces helper instruction read/write functions
for further bp functionality.
Change-Id: I619fbe2870ef6365c29ed1618bb83b6f7eb84690
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5640
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
get_thread_reg() allows gdb to request the register value of a specific
"thread."
set_reg() allows register writes without getting a giant list of
registers first.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I87faa1c8793916b9ee476dd696f0695a07ca2b41
Reviewed-on: http://openocd.zylin.com/5324
Tested-by: jenkins
this change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
a table with register offset will be introduced, thus correct register
addresses will be obtained using this table and the driver internal
function 'stm32l4_get_flash_reg' will be responsible of this.
Change-Id: I74bf61a83fe53575623640af0328b3253ecc796f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5508
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Michael Jung <mijung@gmx.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to RM0432 rev. 6, only 0x1001 "Z" rev. applies for STM32L4P5/Q5.
Verified on real device. Whether other revisions exist is unclear.
Change-Id: I761ae077d089b06925fc0fe1ff2b1e478b8a66fa
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5521
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Introduce a variable 'size' and reduce the number of dereferencing
*reg_list_size by using the variable.
Change-Id: I3bdf1485a4ed8e34435e8acb3efd0df8d802508c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit c2cecc74b0 ("Move JTAG interface list to new files.")
merged in mid 2009 introduces an unused and empty function that
the developer expects to use for loading adapter drivers from
shared libraries. This have never happened and the function is
still empty and unused.
Remove it.
Change-Id: I7c88dbf8a9747e96e5ca4e6e7038ac0f232604fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5601
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
All the servers open the listening socket during openocd "init";
it's not possible to change the tcp port or the bind address
after "init".
In current code, the call order during "init" permits to change
the port and bind address of tcl and telnet server if the related
command is issued after "init" in the same script or on openocd
command line. This is not guaranteed to work if the call order
during "init" changes, so it's incorrect.
Change the commands "bindto" and "*_port" to COMMAND_CONFIG.
Change-Id: Id88f225a67a872b4bcaf3b799466bddedc248015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Christopher Head <chead@zaber.com>
Fixes: https://sourceforge.net/p/openocd/tickets/264/
Reviewed-on: http://openocd.zylin.com/5595
Reviewed-by: Christopher Head <chead@zaber.com>
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: I4efbd9af5be7e16213dcc7cb95de936ecde2fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5173
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Ibac9b36682d58f81e34ca2b51e6260e7d472fb0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5172
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5171
Tested-by: jenkins
GCC 10 defaults to -fno-common which breaks the sharing of bitbang_swd
struct between bitbang drivers due to a missing extern.
Change-Id: I2b4122f7939cec91a72284006748f99a23548324
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5592
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Fix build error on Mac OS X Catalina (10.15.4) caused by formatting
stm32l4_info->wrpxxr_mask, which is uint32_t, as uint16_t in the debug
log message. Adding casting to uint16_t before substitution because only
lower 16 bits are significant for debug purposes.
Change-Id: Iddb87cd156dfc84ab1f91cd15a1ddee6b646d412
Signed-off-by: Ilya Kharin <akscram@gmail.com>
Reviewed-on: http://openocd.zylin.com/5590
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By default the list of VID/PID is empty so if ftdi_vid_pid is not called
then no matches are attempted. The only message is at -d3:
Command 'init' failed with error code -100"
Check for this condition explicitly to make life easier for people
configuring adapters.
Change-Id: If0f93370c9e9ddc9700aae7c346c1c6dd319152e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5440
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The CPU target name is added to the HALT status message so the user
can see which target halted at the designated program counter.
Tested on an Ampere eMAG8180 and Quicksilver silicon
Change-Id: I51e6f21296c85a822df28c5b7c4068e8ff66f29e
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5571
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce a new ERROR_TARGET_ALGO_EXIT as currently used
ERROR_TARGET_TIMEOUT should be reserved for the timeout only.
Do not load PC directly from CPU HW as the register value
has already been cached.
Change-Id: I0d3630da41fd021676789dc12b52545cc0432ba8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5329
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Some flash banks are not mapped in the target memory
(e.g. SPI flash, some special pages).
Add flash version of mdw/h/b which reads data using
the flash driver.
Change-Id: I66910e0a69cf523fe5ca1ed6ce7b9e8e176aef4a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4776
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If watchdog is enabled, there's no way we can disable it while the flashing firmware
is running. (Halt disables it, but software reset doesn't.) So let's have the flashing
firmware refresh the watchdog regularly, in case it has been enabled by previously
running software. Failure to do so could lead to a watchdog reset in the middle of
the chip bieng programmed.
Change-Id: I79d41593948aae0080480e891552e1c2ee3ccbd0
Signed-off-by: Aurélien Martin <martaurel@gmail.com>
Reviewed-on: http://openocd.zylin.com/5266
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
BUILD_TARGET64 creates a larger test matrix and mostly gates the
building of the aarch64/armv8 target, make that unconditional, which
would help fixing any issues with 64-bit address types anyway.
Rebased by Antonio Borneo after commit 1fbe8450a9 ("mips: Add
MIPS64 support")
Change-Id: I219f62b744d540d9dde9a42e6b63fd7d91df3dbb
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5240
Tested-by: jenkins
This is a follow-up change of commit 6d6a69d5 to disable it by
default. The driver was introduced in 6d6a69d5 and enabled by
default in order to run the jenkins build.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Change-Id: I5c5fc6711b971b65dd5846a6163025879044ec40
Reviewed-on: http://openocd.zylin.com/5563
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.
Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit c5d8988316 ("checkpatch.pl:
check for openocd tree, not for kernel tree") has already fixed
the check for OpenOCD tree, thus we do not need to skip it in the
shell wrapper.
Remove flag --no-tree from the shell wrapper.
Change-Id: I8be497258624d89bde7742fee141a8f56bf9188e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5110
Tested-by: jenkins
Drop bogus reference to board/renesas_gen2_common.cfg , which is a
non-existing file.
Fixes: a01474bb4c ("tcl/target: Switch Renesas R-Car Gen2 boards to new config")
Change-Id: Icb22d8456b7ac94d3a9a4ed354b246ee1332b122
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5564
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The stm32mp15x has one or two Cortex-A7 (depending on the P/N) and
one Cortex-M4.
The second core is automatically detected by the target script.
In "engineering boot" all the cores are accessible.
In "production boot" the Cortex-M4 is kept in reset state after
power-on or NRST.
The board DK2 includes a ST-Link/V2, but only SWD is connected.
Change-Id: Ib6ebefcc696b1716e0f98694cadf0b04fd7d11d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5454
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
scan-build-9:
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1075
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1275
ulink_append_xxx_cmd() functions allocate memory for cmd
and then call ulink_allocate_payload(), which allocates cmd->payload_out
or cmd->payload_in.
ulink_append_queue() checks the size of queue and if the new payload
does not fit, calls ulink_execute_queued_commands() and then
ulink_post_process_queue(). If any of these two fails, an error is
returned, allocated cmd struct leaks and the queue is left in an undefined
state.
Change ulink_append_queue() flow to proceed to appending cmd to the queue
even in the case of fail in previous ulink_execute_queued_commands()
or ulink_post_process_queue(). In case of fail then clear the queue
including the last appended cmd.
Change-Id: I967c07af19e9020c93bcb4ef403cf1f557dd1db1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5370
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
scan-build-9:
Description: Access to field 'payload_in' results in a dereference
of a null pointer (loaded from field 'queue_start')
File: src/jtag/drivers/ulink.c
Line: 2216
Set input/output_signals conditionally if ulink_append_get_signals_cmd()
and ulink_execute_queued_commands() returns no error.
Do not fail driver initialisation as the signals are only printed.
Change-Id: I6c842f0e9a604712abf7444a2fa95ba5810de1ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5520
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
core.c:446:
The left operand of '>>' is a garbage value
There are many places where an error code returned from nand->controller
operations are ignored. To keep the change minimal, the error checks are
added only to reading of extended nand info as it was suspected
to be the cause of the warning.
Addition of the error checks did not fix the warning.
scan-build-9 report was inspected and IMHO the warning is bogus:
the term (nand->device->erase_size == 0) cannot give false at line 395
and then evaluate true at line 462. Fixed by zeroing id_buff.
Change-Id: I97ed7ce0fdf1aa23d746d5fb898bacd050e20ae8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5518
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In arc_poll() function we handle the cases, when jtag indicates, that
processor is halted, but target->state is not TARGET_HALTED.
In case, when processor was halted and target->state was TARGET_RUNNING,
we should save context. At the same time if target->state was TARGET_RESET
we do not need to save context.
Changes: 16.04:
Fix - Move setting target->state = TARGET_HALT after
"target->state == TARGET_RUNNIG" check, otherwise
this check makes no sense
Change-Id: I92ab6ec71cf58273bb8401d14a562035de3deab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5524
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
28.02.2020:
-Removed multiple cpu configuration section, currently
only ARC EM is supported.
17.03.2020:
-Some cleanup
-For "arc set-reg-exists" command limitize the number of
arguments (50 maximum).
17.03.2020(v2):
-Revert limitation for "arc set-reg-exist" command
Change-Id: I4b06f89df95f2773bfde6e1bd2ae2b6b880bfaa8
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5351
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
With this commit we add tcl files which describes
ARCv2 architecture features and configure files
for ARCv2 EMSK board.
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
Changes:
22.01.2020:
-Removed "actionpoints" handling code in
tcl/cpu/arc/v2.tcl because this capability
is not supported yet.
Changes:
17.03.2020:
-Update Licence headers
-Cleanup indents
-Removed "reset halt" in boards .tcl
-Updated adapter frequency commands
Changes:
15.03.2020:
-Removed "init" in the of boards .tcl
Change-Id: I51bf620abe7b8e046e1dccc861a7d963965d3a42
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5350
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This reverts commit 6568d29cc1.
The reverted change caused some tasks were missing in thread list.
While on it add a comment explaining the relation of uxTopUsedPriority
and configMAX_PRIORITIES, introduce config_max_priorities and
change types to unsigned.
Change-Id: I4371c8882470d13ee7360ef21b132c56ecb95af8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5577
Tested-by: jenkins
For flash/nor/efm32 the EFM32GG12B Giant chip has been added to the
efm32_family along with its respective series and msc_rebase.
Testen on EFM32GG12B390F board
Change-Id: Idd7dfa93f26ac22566aed1be28f30db678cc0a25
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5567
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
As a consequence of a previous failed SWIM command any
subsequent attempts to enter SWIM mode fails. Change
stlink_usb_mode_enter to use stlink_usb_xfer_noerrcheck
instead.
Change-Id: I5c6a1a8e68d3dc77ec37264880383366fa6a75d9
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5547
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In order to extend the driver to support stlink-server over TCP,
we should always use a valid endpoint, as stlink-server is not permissive
and do not accept the invalid STLINK_NULL_EP.
STLINK_NULL_EP value was used for commands without an expected reply,
this value could be replaced with a valid endpoint without any impact
when the size is set to zero.
Change-Id: I003ad364e03d3a10bc036772db86310d996cbe81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5455
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Antonio Borneo
Marc Schink
Marc Schink
Tarek BOCHKATI
Evgeniy Didin
Tim Newsome
Tomas Vanek
Andreas Bolsch
Andreas Fritiofson
Ilya Kharin
Leonard Crestez
Kevin Burke
Aurélien Martin
Florian Fainelli
Liming Sun
Marek Vasut
tscn92
Ake Rehnman