Commit Graph

292 Commits

Author SHA1 Message Date
Spencer Oliver 9d6ede25dd semihosting: move semihosting cmd to arm cmd group
Move semihosting cmd to the arm cmd group.

Targets that support semihosting will setup the
setup_semihosting callback function.

Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2010-02-28 22:48:37 +00:00
Spencer Oliver 550abe7396 CortexM3: move disassemble cmd to arm cmd group
Rather than using a Cortex disassemble cmd, we now use
the arm generic version.

Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
2010-02-28 22:48:19 +00:00
Mariano Alvira 0324eb2496 Add board/redbee-usb.cfg
The Redbee USB is a small form-factor usb stick from Redwire, LLC
(www.redwirellc.com/store), built around a Freescale MC13224V
ARM7TDMI + 802.15.4 radio (plus antenna).

It includes an FT2232H for debugging, with Channel B connected to the
mc13224v's JTAG interface (unusual) and Channel A connected to UART1.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-28 10:33:46 -08:00
Mariano Alvira 63763345d9 add board/redbee-econotag.cfg and JTAG support
The Redbee Econotag is an open hardware development kit from
Redwire, LLC (www.redwirellc.com/store), for the Freescale
MC13224V ARM7TDMI + 802.15.4 radio.

It includes both an MC13224V and an FT2232H (for JTAG and UART
support).  It has flexible power supply options.

Additional features are:

  - inverted-F pcb antenna
  - 36 GPIO brought out to 0.1" pin header
    (includes all peripheral pins)
  - Reset button
  - Two push buttons (on kbi1-5 and kbi0-4)
  - USB-A connector, powered from USB
  - up to 16V external input
  - pads for optional buck inductor
  - pads for optional 32.768kHz crystal
  - 2x LEDS on TX_ON and RX_ON

[ dbrownell@users.sourceforge.net: shrink lines; texi ]

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-27 22:52:34 -08:00
David Brownell e70d42a727 new "stellaris recover" command
Stellaris chips have a procedure for restoring the chip to
what's effectively the "as-manufactured" state, with all the
non-volatile memory erased.  That includes all flash memory,
plus things like the flash protection bits and various control
words which can for example disable debugger access.  clearly,
this can be useful during development.

Luminary/TI provides an MS-Windows utility to perform this
procedure along with its Stellaris developer kits.  Now OpenOCD
users will no longer need to use that MS-Windows utility.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-27 00:31:35 -08:00
David Brownell 4aa0a4d811 User's Guide mentions OS-specific installation
Specifically the Linux issue of needing "udev" rules, and MS-Windows
needing driver configuration.

Also, update the existing udev note to use the correct name of that
rules file in the source tree.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-21 09:29:24 -08:00
David Brownell 527e073bba User's Guide: "#" in filesystems names is bad
Sometimes MS-Windows users try to use filesystem names which include
the "#" character.  That's generally unwise, since it begins Tcl
comments.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-10 16:42:37 -08:00
David Brownell 84ac6bb0d9 User's Guide: clarify jtag_rclk advice
Not all cores and boards support adaptive clocking, so qualify
all advice to use it to depend on core and board support.

It's primarily ARM cores which support this; and many of the
newer ones (like Cortex-M series) don't.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-10 11:27:48 -08:00
David Brownell 3ea9e62189 Documentation: mention bug database
Have the User's Guide and BUG handling notes both reference
the fact that we now have a bug database at SourceForge.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-04 11:10:15 -08:00
David Brownell 5750e899e0 NOR: User's Guide updates
Remove long-obsolete text about "erase_check" affecting "flash info" output.
Move parts of that text to "protect_check", where it's still relevant; and
update the "flash info" description to mention the issue.

(This is still awkward.  It might be best to make "protect_check" mirror
"erase_check" by dumping what it finds, so "flash info" doesn't dump any
potentially-stale cache info.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-02-02 10:53:13 -08:00
David Brownell 804c0b2ad3 doc clarifications for server flags
The "-f" is a shortcut for "-c" ... and providing any "-c" options
means the "openocd.cfg" file isn't implicitly used.  Both the User's
Guide and the manual page were weak on these points, which has led
to some confusion.

Also update the manual page to include highlights of the search path
mechanism, including the facts that it exists and that "-s" adds to it.
Stop saying only the current directory is involved; the OpenOCD
script library is quite significant.

(Missing: complete manpage coverage of the search path, including a
FILES section listing all components and saying where the script
library is found.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-28 14:03:29 -08:00
David Brownell 08b0be94b5 User's Guide secton on target hardware setup
Highlight the needs to properly jumper development boards; to
make the OpenOCD configuration match the jumpering; and to have
a usable "reset-init" method when debugging early boot code.

Specific mention of the "ATX Mode" that seems useful on
many i.MX boards, forcing NAND boot.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-21 16:15:41 -08:00
David Brownell 20d1ef70e8 User's guide: mention lpc2000 checksum issue
Folk almost certainly want to have OpenOCD compute the checksum
when they modify the vector table.  However, that almost guarantees
that "verify_image" will fail.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-20 00:04:17 -08:00
Peter Korsgaard 000a1cfd01 nand flash support for s3c64xx
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).

Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
2010-01-14 21:07:46 +01:00
David Brownell b60dd35e33 User's Guide updates
Capture various bits of useful information that have come up on the
list but haven't yet gotten into the documentation:

 - Watchdog timers firing during JTAG debug need attention;

 - Some chips have special registers to help JTAG debug;

 - Cortex-M3 stepping example with IRQs and maskisr;

 - Clarifications re adaptive clocking:  not all ARMs do it, and
   explain it a bit better.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-13 23:33:53 -08:00
David Brownell 73566405b6 NOR: add optional "flash erase_address" sector padding
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:

  > flash erase_address 0x0001f980 16
  address range 0x0001f980 .. 0x0001f98f is not sector-aligned
  Command handler execution failed
  in procedure 'flash' called at file "command.c", line 647
  called at file "command.c", line 361
  >

  > flash erase_address pad 0x0001f980 16
  Adding extra erase range, 0x0001f800 to 0x0001f97f
  Adding extra erase range, 0x0001f990 to 0x0001fbff
  erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
  >

This addresses what would otherwise be something of a functional
regression.  An earlier version of the interface had a dangerous
problem:  it would silently erase data outside the range it was
told to erase.  Fixing that bug turned up some folk who relied on
that unsafe behavior.  (The classic problem with interface bugs!)
Now they can get that behavior again.  If they really need it,
just specify "pad".

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-13 23:33:25 -08:00
David Brownell c8267930c7 FreeBSD build fixes
Based on notes from Tomek Cedro <tomek.cedro@gmail.com> and
Steve Franks <bahamasfranks@gmail.com>.

In the User's Guide, sort the list of operating systems reported
through Tcl with $ocd_HOSTOS ... and include FreeBSD.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-10 10:06:58 -08:00
David Brownell ff647e6bb4 parport (mostly) doc fixes
The "parport_port" commands generally don't *require* a port_number;
they're of the "apply any parameter, then print result" variety.  Update
the User's Guide accordingly.

Some of those commands are intended to be write-once: parport_port,
and parport_cable.  Say so.

Use proper EBNF for the parport_write_on_exit parameter.

Parport address 0xc8b8 is evidently mutant.  Say so in the "parport.cfg"
file, to avoid breaking anyone with that mutant config.  But update the
User's Guide to include a sane example for the LP2 port.

Finally document the "presto_serial" command.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-09 21:56:11 -08:00
David Brownell 1c5c57ec8e src/flash/nor: usage/help/doc updates
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets.  Improve and correct various helptexts.

Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.

Add TODO list entry re full support for NAND/NOR bank names.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-09 10:25:03 -08:00
David Brownell fc9a2d0e6f src/server: usage/help/doc updates
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets.  Improve and correct various helptexts.

Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.

Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-09 00:55:41 -08:00
David Brownell 2a76c1bcf9 NAND: help/usage/doc updates
Usage messages should use the same EBNF as the User's Guide;
no angle brackets.  Be more complete too ... some params were
missing.  Improve and correct various helptexts.

Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.

Don't use "&function"; its name is its address.  Line up struct
initializers properly.  Remove some blank lines.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-08 23:18:46 -08:00
David Brownell c1cb20971e Coexist with quilt: rename PATCHES --> PATCHES.txt
The issues is on Win32, which ignores case in filesystem
and thus doesn't tolerate the quilt "patches" directory.

Rename, and add "patches" to .gitignore so that developers
can choose to use quilt for local patch management.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-08 17:20:47 -08:00
David Brownell 82c0fb5277 ARM966: help/usage updates
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.

Fix the User's Guide to say where the magic CP15 bits are defined;
and add comments in case someone provides mcr/mrc methods.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:39:32 -08:00
David Brownell e7965cd3eb Xscale: User's Guide updates
Fix some EBNF goofs ... these commands have *optional* params, etc

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:34:44 -08:00
David Brownell a42bea654c ARM720: help/usage updates
Deprecate the "pass an instruction opcode" flavor of cp15
access in favor of the "arm mcr ..." and "arm mrc ..."
commands, which offer fewer ways to break things.

Use the same EBNF syntax in the code as for the user's guide.

Update User's Guide to say where to find those magic values
(which table in the ARM920 TRM).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:30:09 -08:00
David Brownell e0b6e5deef ARM720: help/usage updates
Deprecate the "pass an instruction opcode" flavor of cp15 access
in favor of the "arm mcr ..." and "arm mrc ..." commands, which
offer fewer ways to break things.

Use the same EBNF syntax in the code as for the user's guide.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:25:03 -08:00
David Brownell 199abf49ea ARM11: help/usage updates
Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.

Uupdate some helptext to be more accurate.

Fix the User's Guide in a few places to be more consistent (mostly
to use brackets not parentheses) and to recognize that parameter may
be entirely optional (in which case the command just displays output,
and changes nothing).  Also reference NXP, not Philips, for LPC chips.

Don't use "&function"; functions are like arrays, their address
is their name.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:21:24 -08:00
David Brownell 48d51e1719 ARM7/ARM9: help/usage updates
Provide helptext which was sometimes missing; update some of it
to be more accurate.

Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.

Fix the User's Guide in a few places to be more consistent (mostly
to use brackets not parentheses) and to recognize that parameter may
be entirely optional (in which case the command just displays output,
and changes nothing).  Also reference NXP, not Philips, for LPC chips.

Don't use "&function"; functions are like arrays, their address
is their name.  Shrink some overlong lines.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:20:14 -08:00
David Brownell 17921f51ab ARMv7: help/usage updates
Provide helptext which was sometimes missing; update some of it
to be more accurate.

Usage syntax messages have the same EBNF as the User's Guide;
there should be no angle brackets in either place.

Don't use "&function"; functions are like arrays, their address
is their name.  Shrink some overlong lines, remove some empties.

Add a couple comments about things that should change:  those
extra TCK cycles for MEM-AP reads are in the wrong place (that
might explain some problems we've seen); the DAP command tables
should be shared, not copied.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-07 16:18:01 -08:00
David Brownell b3bf1d12b2 streamline and document helptext mode displays
Most commands are usable only at runtime; so don't bother saying
that, it's noise.  Moreover, tokens like EXEC are cryptic.  Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are

 - Configuration commands (per documentation)
 - And also some commands that valid at *any* time.

Update the docs to note that "help" now shows this mode info.

This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been.  This just fixes ones I noted when sanity testing.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2010-01-02 15:52:35 -08:00
David Brownell 384e9193e9 User's Guide: warn about the forum
Namely, that developers don't hang out; it's a users-only club.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-31 03:09:03 -08:00
Antonio Borneo 7c5acf8660 whitespace cleanup, mostly for docs
Remove useless space/tab at end of lines.
Remove spaces in indentation and replace with tab.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-30 11:51:29 -08:00
David Brownell ec297e4bf1 Fix Luminary FT2232 layout docs/configs
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:

 - Recent rev C lm3s811 eval boards didn't work.  They must use
   the ICDI layout, which sets up some signals that the older
   boards didn't need.  This is actually safe and appropriate
   for *all* recent boards ... so just make "luminary.cfg" use
   the ICDI layout.

 - "luminary-lm3s811.cfg", was previously unusable!  No VID/PID;
   and the wrong vendor string.  Make it work, but reserve it
   for older boards where the ICDI layout is wrong.

 - Default the LM3748 eval board to "luminary.cfg", like the
   other boards.  If someone uses an external JTAG adapter, all
   boards will use the same workaround (override that default).

The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it.  Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-28 12:59:47 -08:00
David Brownell 155a6a2c0b NOR: make flash_write_unlock() pad to sector end
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.

Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.

We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-27 11:34:31 -08:00
Catalin Patulea 84dbf8ab5a Driver for USB-JTAG, Altera USB-Blaster and compatibles
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-26 15:05:06 -08:00
David Brownell e7f81c11c9 User's Guide: update GDB info
Advise leaving background polling enabled; fix broken URL;
add simple program startup example.
2009-12-26 10:35:24 -08:00
Dean Glazeski 3ac2a44041 AT91SAM9 NAND flash driver.
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip.  This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-19 13:26:33 -08:00
David Brownell abe8b43755 ETM: add "etm trigger_debug" command
In conjunction with manual register setup, this lets the ETM trigger
cause entry to debug state.   It should make it easier to test and
bugfix the ETM code, by enabling non-trace usage and isolating bugs
specific to thef ETM support.  (One current issue being that trace
data collection using the ETB doesn't yet behave.)

For example, many ARM9 cores with an ETM should be able to implement
four more (simple) breakpoints and two more (simple) watchpoints than
the EmbeddedICE supports.  Or, they should be able to support complex
breakpoints, incorporating ETM sequencer, counters, and/or subroutine
entry/exit criteria int criteria used to trigger debug entry.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-19 13:09:19 -08:00
David Brownell 9abad965ab ETM trigger_percent becomes an ETB command
This command was misplaced; it's not generic to all traceport drivers,
only the ETB supports this kind of configuration.  So move it, and
update the relevant documentation.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-19 13:06:46 -08:00
David Brownell 2c3e413d49 JTAG: shrink "scan_chain" output
Tweak the "scan_chain" output by removing column separators.  Also
remove the "current instruction" state ... which changes constantly.

Now its style resembles the "targets" output, and can even fit on
one line in standard terminals and in the PDF docs.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-16 14:19:44 -08:00
mkdorg@users.sourceforge.net 646ce814b4 target: add basic dsp563xx support 2009-12-15 18:38:52 +01:00
David Brownell af79925eb1 jtag: add '-ignore-version' option
Add a "-ignore-version" to "jtag newtap" which makes the IDCODE
comparison logic optionally ignore version differences.

Update the "scan_chain" command to illustrate this by showing
the "*" character instead of the (ignored) version nibble.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-14 15:55:51 -08:00
David Brownell 81aec6be04 ARM: list number of HW breakpoints/watchpoints
When starting up, say how many hardware breakpoints and watchpoints
are available on various targets.

This makes it easier to tell GDB how many of those resources exist.
Its remote protocol currently has no way to ask OpenOCD for that
information, so it must configured by hand (or not at all).

Update the docs to mention this; remove obsolete "don't do this" info.
Presentation of GDB setup information is still a mess, but at least
it calls out the three components that need setup.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-07 14:57:44 -08:00
David Brownell 927ae6899d User's Guide: add quickie setup notes
Add a brief "setup with no customization" note showing the
how easily things can work if standard OpenOCD config scripts
already exist.  We've had some new users comment that this
information is needlessly hard to find, so that starting to
use OpenOCD is more difficult than it should be.

Plus describe a few other issues that come up when setting
up an OpenOCD server.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-07 14:57:44 -08:00
David Brownell 5da53f17f0 User's Guide: mention ETM on ARM11 comes up too
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-07 14:57:43 -08:00
Zachary T Welch 30a6e683b8 add 'flash list', rewrite 'flash banks'
Rename the existing 'flash banks' implementation as 'flash list', and
replace the broken 'flash_banks' TCL wrapper with a new command handler.

Adds documentation for the new 'flash list' command in the user guide.
2009-12-06 21:39:35 -08:00
David Brownell acd6d33994 User's Guide: more semihosting info
List it in the concept index, in the section about target software
changes a project might want to consider, and in the section about
debug messaging.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-04 10:11:31 -08:00
Nicolas Pitre ed59dfc80a basic ARM semihosting support
Semihosting enables code running on an ARM target to use the
I/O facilities on the host computer. The target application must
be linked against a library that forwards operation requests by
using the SVC instruction that is trapped at the Supervisor Call
vector by the debugger.  The "hosted" library version provided
with CodeSourcery's Sourcery G++ Lite for ARM EABI is one example.

This is currently available for ARM9 processors, but any ARM
variant should be able to support this with little additional work.

Tested using binaries compiled with Sourcery G++ Lite 2009q1-161
and ARM RVCT 3.0.

[dbrownell@users.sourceforge.net: doc tweaks, NEWS]

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-03 18:42:01 -08:00
David Brownell a65e75ea34 Tcl and doc: update to match new 'arm mcr ...' etc
Make them match the C code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-12-01 01:10:19 -08:00
Marek Vasut 17b7600a59 XScale: initial PXA3xx support
[dbrownell@users.sourceforge.net: user's guide; variant param is optional]

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-11-29 12:57:05 -08:00