These messages helps to clarify current status of examination process
Change-Id: I5d93903c4680deed2c1bf707d8f7ef0b48ffdc9a
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8013
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This functionality can be useful for;
1-ESP flashing code to load flasher stub on target and
write/read/erase flash.
2-ESP GCOV command uses some of these functions to run
onboard routines to dump coverage info.
This is high level api for the Espressif xtensa and riscv targets
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I5e618b960bb6566ee618d4ba261f51af97a7cb0e
Reviewed-on: https://review.openocd.org/c/openocd/+/7759
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Introduce 'cmsis-dap quirk' command to enable and
disable quirk mode.
If enabled, disconnect and connect before a switch
sequence and do not use multiple packets pipelining.
Change-Id: I6576f7de9f6c98a25c3cf9eec9a456a23610d00d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7966
Tested-by: jenkins
Use it whenever an out-of-sync response is detected to clean
USB bulk transfer state.
USB hidapi does not offer any means to cancel a pending request,
therefore cmsis_dap_hid_cancel_all() does nothing.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ie36fa760c1643ae10be0e87fc633068965a72242
Reviewed-on: https://review.openocd.org/c/openocd/+/7366
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
The synchronous libusb_bulk_transfer() always waits
for the transfer to complete. Therefore it does not allow issuing
multiple USB requests as used on HID backend.
Switch to asynchrounous libusb_submit_transfer().
With this patch a good USB FS based CMSIS-DAPv2 adapter
almost doubles the throughput:
adapter speed: 20000 kHz
poll off
> load_image /run/user/1000/ram256k.bin 0x20000000
262144 bytes written at address 0x20000000
downloaded 262144 bytes in 0.428576s (597.327 KiB/s)
> dump_image /dev/null 0x20000000 0x40000
dumped 262144 bytes in 0.572875s (446.869 KiB/s)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ic6168ea4eca4f6bd1d8ad541a07a8d70427cc509
Reviewed-on: https://review.openocd.org/c/openocd/+/7365
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix the 'wp' command documentation.
Change-Id: I70f3110e8ce286051f8f810260f1857b2285e634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8022
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
By definition in `target/target.h`, `coreid` is not a unique identifier
of a target -- it can be the same for targets on different TAPs.
Change-Id: Ifce78da55fffe28dd8b6b06ecae7d8c4e305c0a2
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7997
Tested-by: jenkins
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When user requested a change on cp0 status register,
it may contain changes on EXL/ERL bits, and changes on
these bits could lead to differnt behaviours on writing
to other cp0 registers.
Change-Id: Ic83039988c29c06ee134226b52de943c46d19da2
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7914
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On this chip, the ndmreset bit in the RISC-V debug module doesn't
trigger a system reset like it should. To work around this, add a custom
"reset-assert" handler in its config file that resets the system by
writing to memory-mapped registers.
I've tested this workaround on a Sipeed Longan Nano dev board with a
GD32VF103CBT6 chip. It works correctly for both "reset run" and "reset
halt" (halting at pc=0 for the latter).
I originally submitted[1] this workaround to the riscv-openocd fork of
OpenOCD. That fork's maintainers accepted it, but have not upstreamed it
like they have several other of my changes.
[1] https://github.com/riscv/riscv-openocd/pull/538
Change-Id: I7482990755b300fcbe4963c9a599d599bc02684d
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6957
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Instead of returning an 'error string', throw an error. This makes it
much easier to handle errors in Tcl scripts or in tools that use Tcl RPC.
Change-Id: I75c48750cfad7430fa5e6bc88fe04ebd59d34cea
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8006
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is useful when using the SEGGER RTT tooling, as the SEGGER RTT
tool J-Link RTT Viewer version 7.84f requires that it receives a
messages immediately after connecting. Otherwise it will give a timeout
and it will not connect.
Change-Id: I9240a1b6a93cd5c0fbd18292afb33b89013d78bf
Signed-off-by: Thiemo van Engelen <tvanengelen@victronenergy.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7752
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: I990c0f7a0871f4b1a0fcdd13afc190149302443c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8003
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: Id32440cdd531077008abd679add32246c4249eb2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8001
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: Idf3d7a46ddecd70823e06bc3997f41fcdb8e501f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8000
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: I676e2ebf5714c850a436854a32c2e9d2f181d537
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7999
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
Change-Id: I0f4a7f93fdf056e7517c754d6d4ecd7928f1d226
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7992
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The correct syntax is already suggested due to the return
value used.
Change-Id: I971a579014c1eaf13b1932f7fa87c020a8eba69c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7971
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While at it, remove the syntax error messages as the correct
syntax is already suggested due to the return value used.
Change-Id: I9310ba96ed3f8a85c37cee9193e481ad3df02e77
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7969
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The mips opcode macro for the SRL opcode was using the wrong constant
value:
SRA -- Shift right arithmetic
Encoding: 0000 00-- ---t tttt dddd dhhh hh00 0011
SRL -- Shift right logical
Encoding: 0000 00-- ---t tttt dddd dhhh hh00 0010
This corrects the opcode constant for SRL and adds the SRA opcode for
completeness.
There is only one user of MIPS32_OP_SRL in src/flash/nor/cfi.c:
Since the mask constant (0x00000080 for the DQ7 mask) shifted in this
case would never have the sign bit set, it worked fine even though it
was accidentally using the SRA opcode instead of SRL.
Change-Id: I0a80746e2075c7df1ce35b9db00d9d0b997a3feb
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/3613
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable 'mode' was introduced in
commit 4dc8cd201c ("cmsis-dap: add initial cmsis-dap support")
but never has been used (just cleared)
Change-Id: Ia741d181ee8006bd0d872f3358a57e045235741a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7965
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We were previously inadvertently clearing the top 32 bits of SCTLR_EL1
during read_memory/write_memory as a result of using 32-bit operations
to access the register and because the fields used to temporarily
store the register were 32-bit. Fix it.
Change-Id: I657d7f949e1f7ab6bf90609e3f91cae09cade31a
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7939
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Associativity=0 means that only one CMO is needed for all ways.
It could also mean that the cache is 1-way, but this is less likely.
Currently Associativity=0 causes us to hang in the while loop in
decode_cache_reg. Fix it by skipping the loop in this case. We can let
way_shift be set to the arbitrary value of 0 because in the case where
Associativity=0 we only ever shift 0 by it before ORing it into the
CMO operand.
Change-Id: I7c1de68d33f6b3ed627cbb1e2401d43185e4c1e3
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7916
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds target logging to breakpoint
handling code. This makes it easier to
debug multicore/multithread systems.
Change-Id: I6bea8079a457070a8f63d0ce381a4ece6f5a190a
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7922
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If we can't remove bp/wp, we will stuck in endless loop
Change-Id: I44c0a164db1d15c0a0637d33c75087a49cf5c0f4
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7940
Tested-by: jenkins
Reviewed-by: Anatoly P <kupokupokupopo@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Break- and watchpoints are not removed when a target is destroyed
which introduces a memory leak.
Change-Id: I6143d48f7efd765b7752a12fdc337da3496d896f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7956
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In the unusual (and even incorrect) case of running the command
target create ...
before defining an adapter and the associated transport, the
command causes a segmentation fault. E.g.:
openocd -c 'target create cpu cortex-m -endian little'
Check that get_current_transport() returns a valid pointer before
referencing it.
Change-Id: I9796a7e92196ef3df5c7152b27c34102045dc9e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7962
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
I use a script to compare the commands in the code with the ones
in the documentation.
Fix the style of the data to simplify the parsing.
Change-Id: I0f1d7e9ff5e2928312ca1a2f3424f82d2910580a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7960
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
This file is intended to be included in any user's project that
plans to use OpenOCD awareness for FreeRTOS.
It is supposed to be distributed under a permissive license to not
impact the original license of the user's project.
Distribute it under Creative Commons Zero v1.0 Universal license.
Change-Id: I7ac90e8b742517bcafc08c00662625671c8159c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7995
Reviewed-by: Karl Palsson <karlp@tweak.au>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Add the full text of the CC0-1.0 license to the OpenOCD tree. It
was copied directly from:
https://spdx.org/licenses/CC0-1.0.html#licenseText
Add the required tags for reference and tooling.
Change-Id: Iae9c1431b6ffdd68ad5780deb78a257edb0b67f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7994
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.au>
Loading a bitstream to cetrus device crashed due to
missing initialization.
Change-Id: Ibd9a04b84e514f9635af01a2b73bae478e534eb7
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7908
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the TI K3 family AM273 SoC.
For further details, see https://www.ti.com/lit/pdf/spruiu0
Change-Id: Ifa21d0760831f4f525ecd976fb8d086ffdbc9e9f
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7950
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Karl Palsson
Kirill Radkin
Erhan Kurubas
Tomas Vanek
Manuel Wick
Marc Schink
Evgeniy Naydanov
Walter Ji
Thomas Hebb
Thiemo van Engelen
Tobias Diedrich
Ahmed BOUDJELIDA
Peter Collingbourne
Marek Vrbka
ianst
Antonio Borneo
Daniel Anselmi
Nishanth Menon