These error messages will prompt patches to be submitted for missing
.usage or empty fields. All of the below must be resolved before next
release.
The Jim defined commands are excluded from this checklist because the
help text can be set later than during command registration.
strlen(.usage) == 0 means that the command expects no arguments.
Updates to this patch in Gerrit to fix problems below are most
welcome. Anyone can push updated versions of a patch to Gerrit. If
there are no further updates to this patch within a week, it will be
pushed to the master branch to prompt more fixes.
These were caught by launching OpenOCD.
Error: BUG: command 'command' does not have the '.usage' field filled out
Error: BUG: command 'script' does not have the '.usage' field filled out
Error: BUG: command 'power_restore' does not have the '.usage' field filled out
Error: BUG: command 'srst_deasserted' does not have the '.usage' field filled out
Error: BUG: command 'measure_clk' does not have the '.usage' field filled out
Error: BUG: command 'exit' does not have the '.usage' field filled out
Error: BUG: command 'shutdown' does not have the '.usage' field filled out
Error: BUG: command 'gdb_sync' does not have the '.usage' field filled out
Error: BUG: command 'interface_list' does not have the '.usage' field filled out
Error: BUG: command 'target' does not have the '.usage' field filled out
Error: BUG: command 'target init' does not have the '.usage' field filled out
Error: BUG: command 'flash' does not have the '.usage' field filled out
Error: BUG: command 'flash init' does not have the '.usage' field filled out
Error: BUG: command 'flash banks' does not have the '.usage' field filled out
Error: BUG: command 'nand' does not have the '.usage' field filled out
Error: BUG: command 'nand drivers' does not have the '.usage' field filled out
Error: BUG: command 'nand init' does not have the '.usage' field filled out
Error: BUG: command 'pld' does not have the '.usage' field filled out
Error: BUG: command 'pld init' does not have the '.usage' field filled out
Error: BUG: command 'mflash' does not have the '.usage' field filled out
Error: BUG: command 'mflash init' does not have the '.usage' field filled out
Error: BUG: command 'dummy' does not have the '.usage' field filled out
Error: BUG: command 'dummy foo' does not have the '.usage' field filled out
Error: BUG: command 'scan_chain' does not have the '.usage' field filled out
Error: BUG: command 'jtag' does not have the '.usage' field filled out
Error: BUG: command 'jtag init' does not have the '.usage' field filled out
Error: BUG: command 'arm' does not have the '.usage' field filled out
Error: BUG: command 'arm reg' does not have the '.usage' field filled out
Error: BUG: command 'etm' does not have the '.usage' field filled out
Error: BUG: command 'arm7_9' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu arm' does not have the '.usage' field filled out
Error: BUG: command 'arm reg' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu etm' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu arm7_9' does not have the '.usage' field filled out
Error: BUG: command 'target_request' does not have the '.usage' field filled out
^C
oyvind@fierce:~/openocd$ openocd -c "interface dummy" -f board/at91eb40a.cfg 2>&1 | grep -w BUG
Error: BUG: command 'command' does not have the '.usage' field filled out
Error: BUG: command 'script' does not have the '.usage' field filled out
Error: BUG: command 'power_restore' does not have the '.usage' field filled out
Error: BUG: command 'srst_deasserted' does not have the '.usage' field filled out
Error: BUG: command 'measure_clk' does not have the '.usage' field filled out
Error: BUG: command 'exit' does not have the '.usage' field filled out
Error: BUG: command 'shutdown' does not have the '.usage' field filled out
Error: BUG: command 'gdb_sync' does not have the '.usage' field filled out
Error: BUG: command 'interface_list' does not have the '.usage' field filled out
Error: BUG: command 'target' does not have the '.usage' field filled out
Error: BUG: command 'target init' does not have the '.usage' field filled out
Error: BUG: command 'flash' does not have the '.usage' field filled out
Error: BUG: command 'flash init' does not have the '.usage' field filled out
Error: BUG: command 'flash banks' does not have the '.usage' field filled out
Error: BUG: command 'nand' does not have the '.usage' field filled out
Error: BUG: command 'nand drivers' does not have the '.usage' field filled out
Error: BUG: command 'nand init' does not have the '.usage' field filled out
Error: BUG: command 'pld' does not have the '.usage' field filled out
Error: BUG: command 'pld init' does not have the '.usage' field filled out
Error: BUG: command 'mflash' does not have the '.usage' field filled out
Error: BUG: command 'mflash init' does not have the '.usage' field filled out
Error: BUG: command 'dummy' does not have the '.usage' field filled out
Error: BUG: command 'dummy foo' does not have the '.usage' field filled out
Error: BUG: command 'scan_chain' does not have the '.usage' field filled out
Error: BUG: command 'jtag' does not have the '.usage' field filled out
Error: BUG: command 'jtag init' does not have the '.usage' field filled out
Error: BUG: command 'arm' does not have the '.usage' field filled out
Error: BUG: command 'arm reg' does not have the '.usage' field filled out
Error: BUG: command 'etm' does not have the '.usage' field filled out
Error: BUG: command 'arm7_9' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu arm' does not have the '.usage' field filled out
Error: BUG: command 'arm reg' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu etm' does not have the '.usage' field filled out
Error: BUG: command 'at91eb40a.cpu arm7_9' does not have the '.usage' field filled out
Error: BUG: command 'target_request' does not have the '.usage' field filled out
Change-Id: I2c3e529530a15d2295a1950ffc59e8f2fc661012
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/299
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change this functions to make it accessible for other
target implementations.
Change-Id: Ib41fc793cfb4de5439af026c2e8b52e7a9507c85
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this particular edge case of the JTAG API will no
longer be supported.
the in_value buffer must be provided by the caller when
the callback needs the buffer.
Change-Id: I552c72a64af6875f4aa4fa9b923194dcf3b57b64
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/265
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
not needed, reduce area of interface and sharp edges to
API.
Change-Id: I5347352e7595686634bd0de13fcf6de6e55027b0
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/262
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a test if the pointer to the target_init function in the target struct
is set before the function pointer is used.
Change-Id: Ie4ea542f64f35efce8c5bce2ced9b881bf283ec1
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/241
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the flash module clock was set according to a spreadsheet from freescale, now it's set according to the configuration file used by the Freescale Flash Programmer.
both work, but i think it's better to use the one used by a software that's made by Freescale (should be correct...)
Change-Id: I382197a3eb43dd47ff4b9b83d5e05008d5613fc6
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/223
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the unlocking procedure erases the flash mem (even if it wasn't locked), so it should be marked as erased after unlocking.
Change-Id: I5cc6a1e1d6cf4e1f243de532eff54111ffd66187
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/222
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
if JTAG debug request fails then halting with a reset should be attempted.
the failure was ignored previously.
Change-Id: Ibec08e2e97f962d164a110c21aaa80bfc17b7f1a
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/221
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
i had assumed two possible halt/debug states:
- halted + debug mode
- running + not debug mode
turns out this one also exists
- halted + NOT in debug mode
added code to handle this in an appropiate way.
Change-Id: Ia0ddcd55d1890c90d100a9e6f5e84ed8dda812a3
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/220
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
now the flash algorithm running on the 568013 checks the buffer_empty bit (instead of the command_finished bit) before trying to write a new word to the flash mem.
this should speed up the flashing procedure. since it is open loop, this change may reduce the risk of failure. flashing will fail if JTAG speed is such that the flash module cannot keep up.
also, the USTAT register is only read once, as suggested in the flow chart provided by freescale (per. ref. manual @ 6-11)
the last step of the flow chart, exiting after commands are complete, is not implemented.
the algorithm will stay waiting for more data. it is up to the PC side to *not* send more data.
Change-Id: I47fe4b50de7da85f80868f5986a89a7e2152616c
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/219
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
moved reset_jtag to the top, since it will be needed in future changes.
also send a define to the .h
Change-Id: I53ef9c02ffa70e7d0416364525a6fbfef855e222
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/216
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
added logging of target error codes to enable automatic error handling from tcl.
the plan is to use a computer to execute a series of tcl commands, the changes allow simple parsing of return messages to detect errors.
Change-Id: Ia98d3bd036e1b6065b475ffff6c1d30baeaf7417
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/215
Tested-by: jenkins
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes an issue when init is called before init_targets has been
executed.
Make sure init_targets is called before init.
Change-Id: Icd5bd4c2a8eea2e399d9de4e331a77560e9672ac
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/235
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
there are no comments about what the rules w.r.t. null pointers
are and it is inconsistent.
It's simply a bug in the app if we ask about the properties of a null
pointer w.r.t. what kind of target it is. It's equally wrong to say
that it is an arm target as that it isn't an arm target.
Change-Id: I0925a6a5c8b38e594ffa7c3ca4390487b5e9b718
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/168
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
fixes clang warning. Basically the next address pointer is not
used for anything in the fn, except to be examined in debug.
Change-Id: I253519b8e49e54490bbe7da8ec3d2dd31f49052a
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/155
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
check if no target is selected and return error.
Change-Id: Ie8abb63c708d09572b45e88fc6766af108715077
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/148
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This rename is in preparation for cortex_m4 support.
Change-Id: Ic08c298ec6ed2aabc2c39db67191f68b3a51f550
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/147
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
return error when target can not be found instead of ERROR_OK,
split fn.
Change-Id: Iba5232d3862a490d0995c3bfece23685bd6856e3
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/131
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this was a false positive, silence it.
Change-Id: I432e0c466c94cf8fd6bbf0ea153c8501a8a261eb
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/126
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
"Value stored to 'retval' is never read": Check and propagate error
"Dereference of null pointer": Probably bogus, maybe triggered by the null
check on armv7a, so remove the check since it can't be null anyway.
Change-Id: I3bc44e52af1589ff40e6a42deda0ce7f3a25e397
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/119
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Also fix a spelling error and remove the declaration for a non-existent
function from the header.
Change-Id: I13177e2d81aa167c05c1cc766f06924211e6d735
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/118
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Propagate errors unchanged.
Free allocated working area in the error return path.
Remove duplicated cleanup code by rewriting the logic.
As a side-effect, fixes a scan-build warning.
Change-Id: I80e3c0015be672778f916e998c8c2e4f23d7588c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/117
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
GCC doesn't understand that these are in fact initialized if they are
used.
Change-Id: I01988adb0547f785b48d869ddbe44cc17dca4739
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/116
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Fix a few errors with set and unused variables detected by GCC 4.7.0
Change-Id: I59b748e18e514ee9f0cde7883b4ed5116198bd4a
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/36
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code in xscale_receive() that tries to skip invalid reads (i.e.
reads that don't have the DBG_SR[0] 'valid' bit set) seems to be
wrong, as it only looks at the first word's valid flag rather than
each word's own valid flag. Am I reading the code correctly? If so,
the attached patch should fix it.
If this looks correct, I'll generate a proper patch and commit message.
Matt
Change-Id: I74ebe2ad7a36d340a9dd3b8487578b6ea7f3cf1e
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/32
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Change-Id: I1453f4f3dc0add529da20577e38b8b82d7d00366
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/18
Reviewed-by: Alex Austin <alex.austin@spectrumdsi.com>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Mathias K
Øyvind Harboe
rodrigo_l_rosa
Spencer Oliver
Andreas Fritiofson
Freddie Chopin
Matt Reimer
Spencer Oliver
Michel Jaouen