STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().
Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h
Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Issue has been found when I tried to read 64 MiB QSPI flash bank.
Bank is memory mapped, default_flash_read() is used for 'flash read_bank'
command. OpenOCD consumed as much as 6.8 GiB of RAM during this
process. Investigation showed that this happens because JTAG queue
is not limited in any way. OpenOCD queues 16 millions of AP reads
allocating all corresponding data structures.
Most of this memory is allocated in:
cmd_queue_alloc (commands.c) - 4.2 GiB
dap_cmd_new (adi_v5_jtag.c) - 2.25GiB
This patch implements a pool of "struct dap_cmd" objects using
linked list. Objects are taken from a pool in "dap_cmd_new()" and
returned to the pool when they are not needed. Size of the pool
is limited to 64K of objects, JTAG queue is forcibly executed
when this limit is reached.
Checked with Valgrind and Clang analyzer - no new warnings.
Change-Id: I5aaaecce5ed71414f7965a2598f49742f6a6b2b5
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4948
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This access port type comes with the AMBA 5 protocol specification,
see 'C1.3 AP' in ARM IHI 0031D.
Change-Id: I3c4f0a69230daaf4f5f979de6213fe3c025a089a
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
The implementation-defined bits have different semantics for each bus
and different recommended defaults.
Change-Id: I562fe24643bb1f3abc696339e382a75ccf2f2873
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of dap_rom_display() and dap_info_command() to
pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Idb97b20759c03fcecbac1184c354966f469caa5f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5073
Tested-by: jenkins
The functions dap_to_jtag() and dap_to_swd() have been introduced by
3ef9beb52c ("ADIv5 DAP ops switching to JTAG or SWD modes") in
arm_adi_v5.c by using the JTAG queue only.
Later, in 6f8b8593d6 ("ADIv5 transport support moves to separate
files") the functions has been moved in adi_v5_swd.c and adi_v5_jtag.c
but keeping the dependency from JTAG queue.
The functions does not work if the current transport is not JTAG.
Move back the functions in arm_adi_v5.c, replace the input parameter
"target" with "dap", use the transport to detect if the JTAG queue is
present, in case of SWD transport use the proper method, for other
transports report error.
Reuse the ADI v5 sequences already present in jtag/swd.h.
Also, OpenOCD does not support switching to another transport after
the initial selection, so do not change DAP's ops vector.
Change-Id: Ib681fbaa60cb342f732bc831eb92de25afa4e4db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4852
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The AP number value is restricted in 8 bits unsigned by ADI-v5
specification. Nevertheless, an "invalid" value is used by
target cortex-m to force an automatic detection of the AP.
Replace magic numbers by using new macros for AP max number and
for the value of AP invalid.
Check the value passed through -ap-num flag during configuration.
Change-Id: Ic19a367db0ab11c0ebd070750eca0647d25279a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4668
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
apcsw command was limited to SPROT bit only.
Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7
Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.
Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Problem: If the same memory location is accessed alternatively
by MEM-AP banked data registers without autoincrement and by standard
autoincremented read/write, TAR register is not updated correctly.
How to replicate: On a Cortex-M issue
mdw 0xe000edf0
multiple times. When poll is on (poll reads the same memory location)
only the first read is correct.
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 20002640
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 00000000
No problems with poll off.
0xe000edf0: 01000000
0xe000edf0: 01000000
0xe000edf0: 01000000
mem_ap_setup_tar() writes to MEM_AP_REG_TAR if requested TAR value
changed or CSW_ADDRINC_... is currently active.
However if an autoincremented access has been issued and autoinc
switched off in CSW afterwards, TAR does not get updated.
The change introduces mem_ap_update_tar_cache() which is called
after queuing of any access to MEM_AP_REG_DRW. It simulates
TAR increment to keep tar_value in sync with MEM_AP.
Crossing tar autoincrement block boundary invalidates cached value.
mem_ap_write() and mem_ap_read() do not check tar autoincrement
block boundary, mem_ap_setup_tar() is called before each transfer instead.
dap_invalidate_cache() is introduced to ensure invalidation
of all cached values during dap_dp_init() and swd_connect()
Change-Id: I815c2283d2989cffd6ea9a4100ce2f29dc3fb7b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4162
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds a Cortex-M private configuration option
that allows setting the acess point during target
creation. This circumvents situations in hybrid systems
when the correct access point can not be automatically
detected.
Change-Id: If313a5250e6e66509bb9080f3498feab7781dced
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3639
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Note:
WCR (Wire Control Register) is replaced by DLCR (Data Link Control
Register). And only TURNROUND field is modifiable.
[andreas.fritiofson@gmail.com]:
Rename DP_IDCODE to DP_DPIDR as well.
Sort list by address and align it using spaces instead of tabs. Add
comments about supporting DP versions.
Remove non-functional wcr command completely.
Change-Id: Ic6b781b07c8eead8b0237d497846d0da060cb1ba
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3244
Tested-by: jenkins
Investigation:
- mem_ap_read_buf_u32() no longer exists.
- JTAG_DP_DPACC & JTAG_DP_APACC are defined in adi_v5_jtag.c now.
Change-Id: I136fc3f389a5a4eb9b68bc759ce653b6da7fa75e
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3243
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
dap_sync() executes all commands in the JTAG queue and then checks
if a WAIT condition happened inside the last batch. If yes, a recovery
is invoked. If not, processing continues without checking for
errors. This function should be called in long AP read or writes, e.g.
while uploading a new application binary, at intermediate points within
the transfer where the cost of flushing the JTAG queue and checking the
journal doesn't affect performance too much.
Change-Id: I99eeaf47cdf951e15e589a04e74b90b5ce911386
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3181
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ADIv5 specifies that DP and AP accesses may generate a WAIT
response when the hardware is not able to complete a request for various
reasons in time before the next request is sent. Currently, the software
treats a WAIT response as a fatal error and aborts operation on the DAP.
This patch implements WAIT handling by keeping a journal of all
outstanding and completed accesses, including their response status.
At certain times (when dap_run() is called), the journal is inspected
for WAIT responses and all discarded accesses are replayed to complete
them. Special care is taken to not re-execute already successfully
completed operations.
Change-Id: I2790070388cf1ab2e8c9a042d74eb3ef776aa583
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3166
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Remove entirely the concept of a "selected" AP that has to be maintained
between calls. All the information the DAP ops need are now provided to
each call through the AP/DAP pointer.
Consolidate the cache of the SELECT fields into one single field caching
the entire register.
Change-Id: I2e1c93ac5ee8ac38a7d680ca2c660c30093a6b87
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3165
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Move the mandatory dap_ap_select() call into the dap_queue_ap_read/write
wrapper.
This avoids the need for dap_ap_select() and the notion of a "current" AP
within target code.
Change-Id: I5cde8f3eef2c662f7458be6f3b3dd44ea693bd74
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3164
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All mem_ap_* functions now make sure the SELECT register is updated with
the AP number that it's operating on. This shouldn't have to be handled
explicitly.
Change-Id: Ib193d8930fabb6a25715064355f98258c9580b5d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function does two separate things, powering up the DP and setting
up a MEM-AP. But the DP needs to be powered before even searching for a
MEM-AP to initialize and targets may have multiple MEM-APs that need
initializing.
Split the function into dap_dp_init() and mem_ap_init() and change all
call sites to use the appropriate one.
Change-Id: I92f55e09754a93f3f01dd8e5aa1ffdf60c856126
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3151
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reduce use of magic numbers and add AXI type MEM-AP detection. Don't try
to call dap_rom_display on a non-existent AP.
AP identification is unique per designer, so make sure the JEDEC code
matches ARM when interpreting the AP type.
Change-Id: I8e86b7de61811382afe99bf15094ab71b43f5fdf
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3150
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change the debug_ap and memory_ap fields of the cortex_a target and
the debug_ap field of the cortex_m target to be pointers to the
struct adiv5_ap instead of AP numbers in some known DAP.
This reduces the dependency on the DAP struct in the targets and
enables MEM-AP accesses to take the relevant AP as parameter.
Change-Id: I39d7b134d78000564b7eec5bff464adf0ef89147
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3147
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This required fixing the AP ID parsing in dap_find_ap() to
match IHI0031C. The AXI type was added too.
Change-Id: I44577a7848df37586e650dce0fb57ac26f5f858c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3146
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This will make it possible to reference directly the AP used for debug
in the target instance and remove the DAP reference. This will in turn
enable getting rid of the need to select an "active" AP in the DAP (using
dap apsel).
Change-Id: I265846a427c714204f4fd3df3cdb75843686c2d0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3144
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Not clear what it was supposed to be used for. It probably shouldn't.
Change-Id: Ife1d833e59ba80f93876447d752a0ca7e7b57b0f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3143
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Cortex-A and Cortex-M keeps an arm_jtag struct around just to be
able to pass a pointer to it to one common JTAG function which anyway
only uses the TAP field.
Refactor the function to take a TAP directly, remove the legacy struct
from cortex instances and store the TAP pointer only in the DAP.
Cortex-M makes a call to arm_jtag_setup_connection() with the struct
but the function does nothing useful for a Cortex-M target so remove
the call.
Change-Id: I3b33709ef55372ef14522ed4337e9f2e817ae3ab
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Separate out the values from adiv5_dap that are associated with a specific AP into a new struct, so we can properly support multiple APs. Remove the DAP struct from the armv7* structs, because we can have multiple CPUs per DAP, and we shouldn't have multiple DAP structs. Tidy up a few places where ap_current is used incorrectly.
Change-Id: I0c6ef4b49cc86b140366347aaf9b76c07cbab0a8
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2984
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Prepare to support multiple cortex-m cores on one DAP. Uses mem_ap_sel_*
functions and removes mem_ap_* functions. Adds a new debug_ap
parameter to the cortex_m (currently set to zero as in existing code).
Change-Id: I6926029d1e7bf44a42d453d1aff349bda824ba72
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2983
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
ERROR_WAIT is better than ERROR_FAIL in timeout condition.
Change-Id: Iefe837f276a9091ce6c18db5947212c449f49d89
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2934
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is a TODO in the src/target/arm_adi_v5.h for MEM-AP registers.
Some new registers are introduced in ADIv5.2 specification.
MEM_AP_REG_MGT (0x20) // Memory Barrier Transfer register
MEM_AP_REG_TAR64 (0x08) // Bits[63:32] of Transfer Address
MEM_AP_REG_BASE64 (0xF0) // Bits[63:32] of Debug Base Address
Refer to
7.5 MEM-AP register summary in
IHI0031C: ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
Change-Id: I3bc4296a04c35f5c64f851e5865d3099922613fa
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2904
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When communication with target fails for whatever reason, it makes
sense to do JTAG-to-SWD (in case the target got power-cycled or the
DAP method was reset anyhow), SWD line reset sequence (part of
JTAG-to-SWD already) and the mandatory IDCODE read. Schedule that to
be performed on the next poll.
Fix the return values for ftdi and jlink drivers to be consistent with
OpenOCD error codes and remove ad-hoc calls to perform DAP method
switching (as it's now done from the upper layer automatically).
Change-Id: Ie18797d4ce7ac43d8249f8f81f1064a2424e02be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2371
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mateusz Manowiecki <segmentation@fault.pl>
When looking for a debug base address of a core, one should search
through all the ROM tables, not just the top-level one.
This code also assumes that the first found entry (in a depth-first
search) will correspond to core 0, the second to core 1 etc.
The patch is supposed to be an alternative implementation of
http://openocd.zylin.com/#/c/1313/.
Change-Id: Ifc88971a02fe3d9c00d9bf72a822ade5804d4e09
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Also align them with spaces instead of tabs.
Change-Id: I1c01412a3ea77b29e8e133f5c92d05ed79d7c0f3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2133
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These features are not currently used so remove or disable them before
something starts to. Not having them around simplifies redesign of the
APIs.
Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1955
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Increases performance by a factor of two for long reads.
Change-Id: I81a7a83835058560c6a53a43c3cc991100f01766
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1954
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix bug in parity calculation macro.
Cache and update the selected DP bank when necessary.
Add aborts when the Ack code signals a failure (we should really only
clear the sticky bits, but this will do for now).
Change-Id: I38a4da136ba1d9e989b33c1875a80c0b1b2be874
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1950
Tested-by: jenkins
Previous to this commit 'ahbap_debugport_init' would ignore if timeout
happened or not when waiting for CDBGPWRUPACK and CSYSPWRUPACK and would
continue initialization regardless. It also would not reset the
timeout counter after finishing polling for CDBGPWRUPACK and starting
for CSYSPWRUPACK which could potentially cause some problems.
Also refactor code of both snippets into a more generic function to
avoid duplication.
Change-Id: I16e4f50e6819e08c4126e71ef8cec7db559d608e
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2086
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's far nicer to pass a size parameter than to split the calls to
separate wrappers which are combined to a single function anyway.
Change-Id: I716741ebf916f6f8e9358a31c8f4fe761107c82f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1847
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This eliminates most of the warnings reported when building for
arm-none-eabi (newlib).
Hsiangkai, there're many similar warnings left in your nds32 files, I
didn't have the nerve to clean them all, probably you could pick it
up.
Change-Id: Id3bbe2ed2e3f1396290e55bea4c45068165a4810
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Create a single pair of relatively simple functions to handle all variants
of MEM-AP transfers. This replaces the many separate functions that
handled different access sizes and packed or non-packed transfers, which
were all implemented rather differently.
With this single implementation, performance should be more consistent,
regardless of transfer type.
Change-Id: I89960e437fc6ba68a389c074fab8eac91abcf844
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Antonio Borneo
Bohdan Tymkiv
Marc Schink
Leonard Crestez
Paul Fertser
Tomas Vanek
Matthias Welwarsky
Andreas Fritiofson
Alamy Liu
Matthias Welwarsky
Patrick Stewart
Evan Hunter
Fatih Aşıcı
Andrey Smirnov
Seth LaForge