Value in the 'dscsr' variable is garbage until the DAP queue is run.
Postpone evaluation of the 'secure_state' variable. Reading the
core registers in between will execute the DAP queue.
Change-Id: I44959e882dbafb1b9779e813c3d13f3b3dbcd47f
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7693
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For some trivial case only, replace calls to jim-nvp with calls
to the new OpenOCD nvp.
Change-Id: Ifd9aff32b67748af8ab808e6a6b6e64f5271b888
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7553
Tested-by: jenkins
Cortex-M support for SMP multicore targets.
This SMP implementation unlike older ones does not act
on the first halted target found. It polls targets
until a SMP group is finished and stores eventual
'halted' events instead of emitting them. As soon as polling
of a group is done, poll proceeds with SMP related tasks.
This approach improves detection of a reason why debug
stopped - a correct reason is detected for all targets,
not only for the first found.
Drawback: SMP target group should be defined in the same
order as the targets were defined.
Obsolete gdb 'J' packet/smp_gdb command core switching is not implemented,
use with rtos hwthread.
Only one core is resumed if debug_execution is requested.
Some ideas taken from Graham Sanderson's [4936]
and src/target/aarch64.c
Added error checking of armv7m_restore_context().
Change-Id: I60f5b79e74b624dc2b5835ff10e38ac2ccb23792
Link: [4936]: target/cortex_m: Add smp support for Cortex M | https://review.openocd.org/c/openocd/+/4936
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Cores armv8m, e.g. Cortex-M33, can be instantiated without the
optional Security Extension.
In this case, the secure registers are not present and when GDB
try accessing them it triggers a set of errors.
For armv8m cores without security extension, don't provide to GDB
the description of the secure registers.
Change-Id: I254478a4cf883e85b786df3f62c726b2f40d88d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Torbjörn SVENSSON <torbjorn.svensson@foss.st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 35a503b08d ("arm_adi_v5: add ap refcount and add get/put
around ap use") modifies the examine functions of mem_ap, cortex_m,
cortex_a and aarch64 by calling dap_put_ap() and then looking again
for the mem-ap and calling dap_get_ap().
This causes an issue if the system is irresponsive and the examine
fails and left the AP pointer to NULL. If the system was already
examined the NULL pointer will cause a SIGSEGV.
Commit b6dad912b8 ("target/cortex_m: prevent segmentation fault
in cortex_m_poll()") proposes a fix for one specific case and only
on cortex_m.
Modify all the examine functions by skipping look-up for the AP if
it was already set in a previous examine; the target's AP is not
supposed to change during runtime.
Remove the partial fix for cortex_m as it is not needed anymore.
Change-Id: I806ec3b1b02fcc76e141c8dd3a65044febbf0a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 35a503b08d ("arm_adi_v5: add ap refcount and add get/put around ap use")
Reviewed-on: https://review.openocd.org/c/openocd/+/7392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: Ife875a966a838c37dde987bc584ad0a1f4d020d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After merging [1] 'reset halt' does not work on not responding Cortex-M.
Relax the examined tests and try to set vector catch VC_CORERESET
if debug_ap is available.
While on it add an info about examination state to debug logs.
Fixes: [1] commit 98d9f1168c ("target: reset target examined flag if target::examine() fails")
Change-Id: Ie2e018610026180af5997d70231061a275f05c76
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6745
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I2475524f4c14520e3163572560f4a9f276356ed5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7168
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We have left the camelcase symbols *xPSR* for some time, to avoid
any conflict with possibly pending patches in gerrit.
With the approaching v0.12.0-rc1, it's time to revisit it.
The patches in gerrit that conflict with this rename are all not
merge-able due to conflicts or due to negative review.
Drop these CamelCase symbols.
Change-Id: Ifbac4c1df9cc55994e024971a2aaebeed2ea4ed3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with an PLUS-F5270 board which uses the MM32F5277E9PV.
Signed-off-by: iysheng <iyysheng@gmail.com>
Change-Id: Icb75ae8337fdc6fa60e39d3d74dd8bc163707bdd
Reviewed-on: https://review.openocd.org/c/openocd/+/7136
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The S_RESET_ST sticky bit is reset after DHCSR read.
It is set at power-on reset and keeps active until the debuger reads DHCSR.
Ignore S_RESET_ST at the very first read after OpenOCD start
and suppress possibly misleading message "external reset detected"
if we cannot guarantee the reset happened recently.
While on it add a TODO comment.
Change-Id: I15217c2ca6f69ac97aff8be86bce67cba94a42cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7109
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a Cortex-M MCU become unresponsive during a debug session and
re-examination fails to find MEM-AP, debug_ap pointer is set to NULL.
Eventual call of cortex_m_poll() dereferences debug_ap.
Check debug_ap validity at the begin of cortex_m_poll().
Change-Id: I9519f48760c91a48a9e5e8c34634d247098cb14a
Fixes: 35a503b08d (arm_adi_v5: add ap refcount and add get/put around ap use)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
While an ADIv5 DAP can only have 256 AP, ADIv6 can provide till
2**40 (1,099,511,627,776) AP per DAP.
The actual trivial code implementation for ADIv5 (that uses an
array of 256 ap in the struct adiv5_dap) cannot be extended as-is
to handle ADIv6.
The simple array of 256 AP can be reused as a dynamic storage for
ADIv6 ap:
- the ADIv5 AP number is replaced by the ADIv6 base address;
- the index of the array (equal to ADIv5 AP number) has no link to
any ADIv6 property;
- the ADIv6 base_address has to be searched in the array of AP.
The 256 elements in the AP array should be enough for any device
available today. In future it can be easily increased, if needed.
To efficiently use the 256 elements in the AP array, the code
should associate one element of the array to an ADIv6 AP (through
the AP base address), then cancel the association when the AP is
not anymore needed. This is important to avoid saturating the AP
array while exploring the device through 'dap apreg' commands.
Add a reference counter in the struct adiv5_ap to track how many
times the struct has been associated with the same base address.
Introduce the function dap_get_ap() to associate and return the
struct, and dap_put_ap() to release the struct. For the moment the
code covers ADIv5 only, so the association is through the index.
Use the two functions above and dap_find_get_ap() throughout the
code.
Check the return value of dap_get_ap(). It is always not NULL in
the current ADIv5-only implementation, but can be NULL for ADIv6
when there are no more available AP in the array.
Instrument dap_queue_ap_read() and dap_queue_ap_write() to log an
error message if the AP has reference counter zero, meaning that
the AP has not been 'get' yet. This helps identifying AP used
without get/put, e.g. code missed by this patch, or merged later.
Instrument dap_cleanup_all() to log an error message if an AP has
reference counter not zero at openocd exit, meaning that the AP
has not been 'put' yet.
Change-Id: I98316eb42b9f3d9c9bbbb6c73b1091b53f629092
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6455
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Tested-by: jenkins
The 'set' variable name suggests a boolean data type which determines
whether a breakpoint (or watchpoint) is active. However, it is also
used to store the number of the breakpoint.
This encoding leads to inconsistent value assignments: boolean and
integer values are mixed. Also, associated hardware comparator
numbers, which are usually numbered from 0, cannot be used directly.
An additional offset is required to store the comparator numbers.
In order to make the code more readable and the value assignment more
consistent, change the variable name to 'is_set', its data type to 'bool'
and introduce a dedicated variable for the break-/watchpoint
number.
In order to make the review easier, the data types of various related
variables (e.g. number of breakpoints) are not changed.
While at it, fix a few coding style issues.
Change-Id: I2193f5639247cce6b80580d4c1c6afee916aeb82
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6319
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Unlike cortex_m_load_core_reg_u32() storing core register uses
the same code pattern around DHCSR read as offered by the convenience
helper cortex_m_read_dhcsr_atomic_sticky().
Use the helper.
Change-Id: Ia947204944a8b549f3c2be7fb2f717aad18970c4
SeeAlso: 65d7629183 (cortex_m: poll S_REGRDY on register r/w)
SeeAlso: 0dcf95c717 (target/cortex_m: cumulate DHCSR sticky bits)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6767
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function debugport_init() has never existed in OpenOCD code,
but few comments erroneously references it in place of the
existing function ahbap_debugport_init().
Commit 00dbc185ee ("arm_adi_v5: Split ahbap_debugport_init")
splits the function ahbap_debugport_init() in dap_dp_init() and
mem_ap_init(), but did not removed all the incorrect comments
about debugport_init(). Few of such comments has been removed in
later patches.
Remove the last comment that references debugport_init().
Change-Id: Ibd1f125475386e5653340fedf706903a0ee15897
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6694
Tested-by: jenkins
hla_target uses the same struct cortex_m_common as the standard cortex_m
target. Unlike the cortex_m target hla missed setting of common_magic.
Set commont_magic to help pointer verification.
Add convenience tests is_cortex_m_or_hla() and
is_cortex_m_with_dap_access()
Use proper test in cortex_m_verify_pointer() - this code relied on
unset common_magic on hla target before the change.
Change-Id: I4dae79f056c3d73adf524e26aa8ef2d3a57b471e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6741
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If the target is in a state where S_REGRDY polling is necessary (slow
clock, low power state...?), OpenOCD will continue to use the slow
path even if the condition is temporary and the target at a later
point would be capable of fast reads again.
Revert to fast reads if a full register dump can be made without need
for polling any of the registers; presumably it will succeed the next
time too.
Change-Id: I557f0d90b7ce6f9d81aa409b6400fc9c83d16008
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6678
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the change cortex_m_debug_entry() reads all registers
calling cortex_m_load_core_reg_u32() for each register with
a poor usage of JTAG/SWD queue.
It is time consuming, especially on an USB FS based adapter.
Moreover if target_request debugmsgs are enabled, DCB_DCRDR
is saved and restored on each register read.
This change introduces cortex_m_fast_read_all_regs()
which queues all register reads and a single dap_run() transaction
does all work.
cortex_m_fast_read_all_regs() reads all registers unconditionally
regardless register cache is valid or not. This is a difference
from the original cortex_m_debug_entry() code.
cortex_m_debug_entry times from -d3 log, Cortex-M4F and CMSIS-DAP
(Kinetis K28F-FRDM kit)
target_request | time [ms]
debugmsgs | without the change | with the change
---------------+--------------------+-----------------
disable | 186 | 27
enable | 232 | 29
Added checking of DHCSR.S_REGRDY flag. If "not ready" is seen,
cortex_m->slow_register_read is set and fallback to the old
register read method cortex_m_slow_read_all_regs() is used
instead of cortex_m_fast_read_all_regs().
Change-Id: I0665d94b97ede217394640871dc451ec93410254
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5321
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Accordingly to arm documentation [1], chapter C1.6.4, the
operation to read/write from/to core registers can require time,
and the specific flag DHCSR.S_REGRDY has to be polled to verify
that the operation has been completed.
The lack of check on S_REGRDY causes OpenOCD to fail handling
correctly the core registers on a Cortex-M4 emulated in a slow
FPGA, and it could also fail on devices clocked at very low speed
while using a fast adapter.
Poll S_REGRDY as specified in [1] while either reading or writing
the core registers.
A timeout of 0.5s is added. This could still be too small in some
extremely slow cases, but at least now we log the timeout event,
which can help tracking down such odd issue.
During register read include in the polling loop the read of DCRSR
and to flush the JTAG queue only once.
During register write, relax the write in DCRSR by removing the
atomicity that is now useless since followed by the atomic read to
S_REGRDY.
During register read include the read of DCRSR inside the polling
loop to relax the read of S_REGRDY since followed by the atomic
read to DCRSR.
This change has the drawback of adding other transfers to the
adapter while reading/writing the registers, so it is expected to
introduce some speed degradation during step-by-step.
[1] DDI0403E - "ARMv7-M Architecture Reference Manual"
Change-Id: I61f454248f11a3bec6dcf4c58a50c5c996d7ef81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5319
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
DCB DHCSR register contains S_RETIRE_ST and S_RESET_ST bits cleared
on a read.
The change introduces a helper function cortex_m_cumulate_dhcsr_sticky().
Call this function each time DHCSR is read to preserve S_RESET_ST state
in the case of a reset event was detected.
Introduce cortex_m_read_dhcsr_atomic_sticky() convenience helper to
read DHCSR, store it to cortex_m->dcb_dhcsr and cumulate sticky bits.
The cumulated state of S_RESET_ST is read and cleared in cortex_m_poll()
Change-Id: Ib679599f850fd219fb9418c6ff32eed7cf5740da
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6180
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cortex_m->dcb_dhcsr caches status of DHCSR register.
Use it instead of local variable in cortex_m_soft_reset_halt()
like in other code.
Extracted from [1].
[1] Antonio Borneo: 6207: cortex_m: rework handling of dcb_dhcsr
Link: https://review.openocd.org/c/openocd/+/6207
Change-Id: I9a0aeba0b6b0b4969f05f4a32fc2fc8d244f56ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6677
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cortex_m_single_step_core() used mem_ap_write_atomic_u32() to manipulate
dhcsr bits unlike the rest of code, where a specialized function
cortex_m_write_debug_halt_mask() takes place.
Unify setting of dhcsr bits and use cortex_m_write_debug_halt_mask() here as well.
Extracted from [1].
[1] Antonio Borneo: 6207: cortex_m: rework handling of dcb_dhcsr
Link: https://review.openocd.org/c/openocd/+/6207
Change-Id: I9ef05ce88a9dce42e1d3d5404a4fe87ec86b5fe8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6676
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Giving the example of STM32WL55x the examine log is the following:
Info : stm32wlx.cpu0: hardware has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: hardware has 4 breakpoints, 2 watchpoints
After this change the examine log becomes:
Info : stm32wlx.cpu0: Cortex-M4 r0p1 processor detected
Info : stm32wlx.cpu0: target has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: Cortex-M0+ r0p1 processor detected
Info : stm32wlx.cpu1: target has 4 breakpoints, 2 watchpoints
Change-Id: I1873a75eb76f0819342c441129427b38e984f0df
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6553
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The include file 'armv7m.h' includes 'arm_adi_v5.h' only to get
the definition of 'struct adiv5_ap', but doesn't need the struct
content.
Reducing the cross dependencies speeds-up the compile time during
code development by avoiding re-compiling file.
Relax the dependency by locally declaring 'struct adiv5_ap' in
'armv7m.h' and remove the include of 'arm_adi_v5.h'.
Fix the other files that have now lost the includes file that
'arm_adi_v5.h' depends from.
Change-Id: Ic0d40b17db6045fa43f348bda83eaf211a6b347d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6468
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The command 'step' accepts an optional parameter 'address' to run
the step-by-step execution from an address different from current
program counter.
When OpenOCD sets the new program counter value in the register
cache, it doesn't flag it as dirty. The following call to function
armv7m_restore_context() does not propagate the new value of the
program counter to the target. This cause the target to continue
from the old program counter value, ignoring the user's request.
It is hard to notice the issue if the target is halted in an idle
loop! In fact the default mode to operate step-by-step is to set a
breakpoint to the following instruction and resume execution. In
the idle loop the CPU will pass through the breakpoint whatever
the resume address is. User will find the target halting at the
instruction following 'address' which is consistent with the
expected behaviour of command 'step address'.
To verify the issue on an STM32F4, use a dummy code in SRAM:
halt
mww 0x20000000 0xbf00bf00
mww 0x20000004 0xbf00bf00
mww 0x20000008 0xe7fcbf00
arm disassemble 0x20000000 6
0x20000000 bf00 nop
0x20000002 bf00 nop
0x20000004 bf00 nop
+--> 0x20000006 bf00 nop
| 0x20000008 bf00 nop
+-<- 0x2000000a e7fc b #0x20000006
resume 0x20000006
halt
step 0x20000000
the target doesn't halt because it is in the loop from 0x20000006
to 0x2000000a. The 'step 0x20000000' did not changed the program
counter so the temporary breakpoint at 0x20000002 is never hit.
Then:
halt
step 0x20000008
target halted ...
... pc: 0x2000000a
gives the feeling that only the instruction at 0x20000008 has been
executed, but actually the whole loop has been executed from the
place 'halt' stopped the execution till the breakpoint at the
instruction following 0x20000008.
Flag the program counter cached value as 'valid' and 'dirty' to
force armv7m_restore_context() to update the target's register.
Change-Id: I49bd8bb95b2f5429ec38ed016f2ad706618ae68a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6434
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
The HLA target is not anymore used by ST-Link only, but required
by Nu-Link and TI-ICDI too.
Rename the flag 'stlink' as 'is_hla_target'.
Change-Id: Id2ee2c0a1e8bf1f1e899f7a560140c34eefeeee5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6206
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Rework core detection by adding cortex_m_partno enum to detect all CPUs
using the same method.
Instead of checking the core PARTNO then assign the arch, use the stored
information within cortex_m parts[] with the flags inside which can help
simplifying a bit the cortex_m_examine code.
This change fixes:
- the Cortex-M1 detection as ARMv6-M Core (was managed as ARMv7-M)
- the displayed CPU name for Cortex-M0+ (was displayed Cortex-M0)
Change-Id: I40b6e03f7cf3664c85e297adfc25323196dfe90b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6233
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In target/arm.h the struct arm do contain 3 flags to retain architecture
version for some tweaks.
The proposal is to have only one enumerated flag 'arch' for the same purpose.
Change-Id: Ia5d5accfed8158ca21eb54af2fdea8e36f0266ae
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this change aims to provide a better gdb debugging experience,
by making gdb understand what's really happening.
before this change when hitting a watchpoint
- openocd reports "T05" to gdb
- gdb displays: Program received signal SIGTRAP, Trace/breakpoint trap.
after the change
- openocd reports "T05watch:20000000;" to gdb
- gdb displays:
Hardware watchpoint 1: *0x20000000
Old value = 16000000
New value = 170000000
...
Change-Id: Iac3a85eadd86663617889001dd04513a4211ced9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6181
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some target name were marked as deprecated in release v0.7.0 and
v0.8.0, almost 7 years ago, and replaced with more 'actual' names.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.8.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the target names already deprecated in v0.8.0.
Change-Id: I7c7491496db1b302b4eb1e9fc6090b58d4acf05a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6086
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
If the command 'itm port[s]' is issued before 'init', the ITM can
not be programmed because OpenOCD cannot access the target yet.
The configuration is recorded and applied after target examine.
The current test to trigger the ITM delayed-programming is based
on the TPIU configuration. This is allowed because the only use of
ITM it so send data through TPIU.
In case of system TPIU, not belonging anymore to the target, there
is no more association between target ITM and system TPIU.
Add a flag to record the pending ITM configuration requested
before 'init' and test the flag to trigger the delayed-programming
of the ITM.
Change-Id: I101eb97a116d7925cd2ff068f3e8813fc008b08e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6029
Tested-by: jenkins
If OpenOCD is reading trace data from the target, at exit it
should stop the adapter to gather data, but should left the target
still producing them.
Add a helper in armv7m_trace to disable the adapter's trace and
call it during OpenOCD teardown.
This also provides a workaround for an issue in the firmware of
ST-Link V3 till version V3J7. If the SWD connection is closed when
trace is active, at following connection the trace does not work
anymore.
Change-Id: I47ccab61405384938555096c5aca789eaa090d27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5978
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Bohdan Tymkiv
Antonio Borneo
Tomas Vanek
iysheng
Marc Schink
Tarek BOCHKATI
Andreas Fritiofson
Yasushi SHOJI
Tarek BOCHKATI