Unlike cortex_m_load_core_reg_u32() storing core register uses
the same code pattern around DHCSR read as offered by the convenience
helper cortex_m_read_dhcsr_atomic_sticky().
Use the helper.
Change-Id: Ia947204944a8b549f3c2be7fb2f717aad18970c4
SeeAlso: 65d7629183 (cortex_m: poll S_REGRDY on register r/w)
SeeAlso: 0dcf95c717 (target/cortex_m: cumulate DHCSR sticky bits)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6767
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function debugport_init() has never existed in OpenOCD code,
but few comments erroneously references it in place of the
existing function ahbap_debugport_init().
Commit 00dbc185ee ("arm_adi_v5: Split ahbap_debugport_init")
splits the function ahbap_debugport_init() in dap_dp_init() and
mem_ap_init(), but did not removed all the incorrect comments
about debugport_init(). Few of such comments has been removed in
later patches.
Remove the last comment that references debugport_init().
Change-Id: Ibd1f125475386e5653340fedf706903a0ee15897
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6694
Tested-by: jenkins
hla_target uses the same struct cortex_m_common as the standard cortex_m
target. Unlike the cortex_m target hla missed setting of common_magic.
Set commont_magic to help pointer verification.
Add convenience tests is_cortex_m_or_hla() and
is_cortex_m_with_dap_access()
Use proper test in cortex_m_verify_pointer() - this code relied on
unset common_magic on hla target before the change.
Change-Id: I4dae79f056c3d73adf524e26aa8ef2d3a57b471e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6741
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If the target is in a state where S_REGRDY polling is necessary (slow
clock, low power state...?), OpenOCD will continue to use the slow
path even if the condition is temporary and the target at a later
point would be capable of fast reads again.
Revert to fast reads if a full register dump can be made without need
for polling any of the registers; presumably it will succeed the next
time too.
Change-Id: I557f0d90b7ce6f9d81aa409b6400fc9c83d16008
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6678
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the change cortex_m_debug_entry() reads all registers
calling cortex_m_load_core_reg_u32() for each register with
a poor usage of JTAG/SWD queue.
It is time consuming, especially on an USB FS based adapter.
Moreover if target_request debugmsgs are enabled, DCB_DCRDR
is saved and restored on each register read.
This change introduces cortex_m_fast_read_all_regs()
which queues all register reads and a single dap_run() transaction
does all work.
cortex_m_fast_read_all_regs() reads all registers unconditionally
regardless register cache is valid or not. This is a difference
from the original cortex_m_debug_entry() code.
cortex_m_debug_entry times from -d3 log, Cortex-M4F and CMSIS-DAP
(Kinetis K28F-FRDM kit)
target_request | time [ms]
debugmsgs | without the change | with the change
---------------+--------------------+-----------------
disable | 186 | 27
enable | 232 | 29
Added checking of DHCSR.S_REGRDY flag. If "not ready" is seen,
cortex_m->slow_register_read is set and fallback to the old
register read method cortex_m_slow_read_all_regs() is used
instead of cortex_m_fast_read_all_regs().
Change-Id: I0665d94b97ede217394640871dc451ec93410254
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5321
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Accordingly to arm documentation [1], chapter C1.6.4, the
operation to read/write from/to core registers can require time,
and the specific flag DHCSR.S_REGRDY has to be polled to verify
that the operation has been completed.
The lack of check on S_REGRDY causes OpenOCD to fail handling
correctly the core registers on a Cortex-M4 emulated in a slow
FPGA, and it could also fail on devices clocked at very low speed
while using a fast adapter.
Poll S_REGRDY as specified in [1] while either reading or writing
the core registers.
A timeout of 0.5s is added. This could still be too small in some
extremely slow cases, but at least now we log the timeout event,
which can help tracking down such odd issue.
During register read include in the polling loop the read of DCRSR
and to flush the JTAG queue only once.
During register write, relax the write in DCRSR by removing the
atomicity that is now useless since followed by the atomic read to
S_REGRDY.
During register read include the read of DCRSR inside the polling
loop to relax the read of S_REGRDY since followed by the atomic
read to DCRSR.
This change has the drawback of adding other transfers to the
adapter while reading/writing the registers, so it is expected to
introduce some speed degradation during step-by-step.
[1] DDI0403E - "ARMv7-M Architecture Reference Manual"
Change-Id: I61f454248f11a3bec6dcf4c58a50c5c996d7ef81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5319
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
DCB DHCSR register contains S_RETIRE_ST and S_RESET_ST bits cleared
on a read.
The change introduces a helper function cortex_m_cumulate_dhcsr_sticky().
Call this function each time DHCSR is read to preserve S_RESET_ST state
in the case of a reset event was detected.
Introduce cortex_m_read_dhcsr_atomic_sticky() convenience helper to
read DHCSR, store it to cortex_m->dcb_dhcsr and cumulate sticky bits.
The cumulated state of S_RESET_ST is read and cleared in cortex_m_poll()
Change-Id: Ib679599f850fd219fb9418c6ff32eed7cf5740da
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6180
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cortex_m->dcb_dhcsr caches status of DHCSR register.
Use it instead of local variable in cortex_m_soft_reset_halt()
like in other code.
Extracted from [1].
[1] Antonio Borneo: 6207: cortex_m: rework handling of dcb_dhcsr
Link: https://review.openocd.org/c/openocd/+/6207
Change-Id: I9a0aeba0b6b0b4969f05f4a32fc2fc8d244f56ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6677
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cortex_m_single_step_core() used mem_ap_write_atomic_u32() to manipulate
dhcsr bits unlike the rest of code, where a specialized function
cortex_m_write_debug_halt_mask() takes place.
Unify setting of dhcsr bits and use cortex_m_write_debug_halt_mask() here as well.
Extracted from [1].
[1] Antonio Borneo: 6207: cortex_m: rework handling of dcb_dhcsr
Link: https://review.openocd.org/c/openocd/+/6207
Change-Id: I9ef05ce88a9dce42e1d3d5404a4fe87ec86b5fe8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6676
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Giving the example of STM32WL55x the examine log is the following:
Info : stm32wlx.cpu0: hardware has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: hardware has 4 breakpoints, 2 watchpoints
After this change the examine log becomes:
Info : stm32wlx.cpu0: Cortex-M4 r0p1 processor detected
Info : stm32wlx.cpu0: target has 6 breakpoints, 4 watchpoints
Info : stm32wlx.cpu1: Cortex-M0+ r0p1 processor detected
Info : stm32wlx.cpu1: target has 4 breakpoints, 2 watchpoints
Change-Id: I1873a75eb76f0819342c441129427b38e984f0df
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6553
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The include file 'armv7m.h' includes 'arm_adi_v5.h' only to get
the definition of 'struct adiv5_ap', but doesn't need the struct
content.
Reducing the cross dependencies speeds-up the compile time during
code development by avoiding re-compiling file.
Relax the dependency by locally declaring 'struct adiv5_ap' in
'armv7m.h' and remove the include of 'arm_adi_v5.h'.
Fix the other files that have now lost the includes file that
'arm_adi_v5.h' depends from.
Change-Id: Ic0d40b17db6045fa43f348bda83eaf211a6b347d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6468
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The command 'step' accepts an optional parameter 'address' to run
the step-by-step execution from an address different from current
program counter.
When OpenOCD sets the new program counter value in the register
cache, it doesn't flag it as dirty. The following call to function
armv7m_restore_context() does not propagate the new value of the
program counter to the target. This cause the target to continue
from the old program counter value, ignoring the user's request.
It is hard to notice the issue if the target is halted in an idle
loop! In fact the default mode to operate step-by-step is to set a
breakpoint to the following instruction and resume execution. In
the idle loop the CPU will pass through the breakpoint whatever
the resume address is. User will find the target halting at the
instruction following 'address' which is consistent with the
expected behaviour of command 'step address'.
To verify the issue on an STM32F4, use a dummy code in SRAM:
halt
mww 0x20000000 0xbf00bf00
mww 0x20000004 0xbf00bf00
mww 0x20000008 0xe7fcbf00
arm disassemble 0x20000000 6
0x20000000 bf00 nop
0x20000002 bf00 nop
0x20000004 bf00 nop
+--> 0x20000006 bf00 nop
| 0x20000008 bf00 nop
+-<- 0x2000000a e7fc b #0x20000006
resume 0x20000006
halt
step 0x20000000
the target doesn't halt because it is in the loop from 0x20000006
to 0x2000000a. The 'step 0x20000000' did not changed the program
counter so the temporary breakpoint at 0x20000002 is never hit.
Then:
halt
step 0x20000008
target halted ...
... pc: 0x2000000a
gives the feeling that only the instruction at 0x20000008 has been
executed, but actually the whole loop has been executed from the
place 'halt' stopped the execution till the breakpoint at the
instruction following 0x20000008.
Flag the program counter cached value as 'valid' and 'dirty' to
force armv7m_restore_context() to update the target's register.
Change-Id: I49bd8bb95b2f5429ec38ed016f2ad706618ae68a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6434
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
The HLA target is not anymore used by ST-Link only, but required
by Nu-Link and TI-ICDI too.
Rename the flag 'stlink' as 'is_hla_target'.
Change-Id: Id2ee2c0a1e8bf1f1e899f7a560140c34eefeeee5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6206
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Rework core detection by adding cortex_m_partno enum to detect all CPUs
using the same method.
Instead of checking the core PARTNO then assign the arch, use the stored
information within cortex_m parts[] with the flags inside which can help
simplifying a bit the cortex_m_examine code.
This change fixes:
- the Cortex-M1 detection as ARMv6-M Core (was managed as ARMv7-M)
- the displayed CPU name for Cortex-M0+ (was displayed Cortex-M0)
Change-Id: I40b6e03f7cf3664c85e297adfc25323196dfe90b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6233
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In target/arm.h the struct arm do contain 3 flags to retain architecture
version for some tweaks.
The proposal is to have only one enumerated flag 'arch' for the same purpose.
Change-Id: Ia5d5accfed8158ca21eb54af2fdea8e36f0266ae
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this change aims to provide a better gdb debugging experience,
by making gdb understand what's really happening.
before this change when hitting a watchpoint
- openocd reports "T05" to gdb
- gdb displays: Program received signal SIGTRAP, Trace/breakpoint trap.
after the change
- openocd reports "T05watch:20000000;" to gdb
- gdb displays:
Hardware watchpoint 1: *0x20000000
Old value = 16000000
New value = 170000000
...
Change-Id: Iac3a85eadd86663617889001dd04513a4211ced9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6181
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some target name were marked as deprecated in release v0.7.0 and
v0.8.0, almost 7 years ago, and replaced with more 'actual' names.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.8.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the target names already deprecated in v0.8.0.
Change-Id: I7c7491496db1b302b4eb1e9fc6090b58d4acf05a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6086
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
If the command 'itm port[s]' is issued before 'init', the ITM can
not be programmed because OpenOCD cannot access the target yet.
The configuration is recorded and applied after target examine.
The current test to trigger the ITM delayed-programming is based
on the TPIU configuration. This is allowed because the only use of
ITM it so send data through TPIU.
In case of system TPIU, not belonging anymore to the target, there
is no more association between target ITM and system TPIU.
Add a flag to record the pending ITM configuration requested
before 'init' and test the flag to trigger the delayed-programming
of the ITM.
Change-Id: I101eb97a116d7925cd2ff068f3e8813fc008b08e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6029
Tested-by: jenkins
If OpenOCD is reading trace data from the target, at exit it
should stop the adapter to gather data, but should left the target
still producing them.
Add a helper in armv7m_trace to disable the adapter's trace and
call it during OpenOCD teardown.
This also provides a workaround for an issue in the firmware of
ST-Link V3 till version V3J7. If the SWD connection is closed when
trace is active, at following connection the trace does not work
anymore.
Change-Id: I47ccab61405384938555096c5aca789eaa090d27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5978
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If dap_dp_read_atomic() in 30 trials loop fails, dap->do_reconnect is set.
Following dap_dp_read_atomic() calls dap_queue_dp_read() which in case
of SWD transport calls swd_queue_dp_read(). It starts
with swd_check_reconnect() and it calls swd_connect() because
dap->do_reconnect is set. swd_connect() does some initialization,
reads DPIDR and calls dap_dp_init() again!
Moreover if dap_dp_init() is called from cortex_m_reset_(de)assert()
one level of recursion is necessary to reconnect the target.
Introduce dap_dp_init_or_reconnect() for use in cortex_m reset
and similar.
Remove loop of 30 atomic reads of DP_STAT to prevent unwanted recursion.
Change-Id: I54052fdefe50bf5f7c7b59fe751fe2063d5710c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5729
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I4fea29f07f4d3b8b2578b538ef0eef5f1eea285f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5876
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a Cortex-M (not M0, M0+) target was stopped in the middle of
a conditional IT block or in the load/store multiple instruction,
cortex_m_debug_entry() used wrong xPSR bits to detect it and then
cleared 8 bits of the exception number from xPSR
- probably wrong bit mask again.
I believe clearing of the ICI/IT bits in cortex_m_debug_entry() has no
reason as Cortex-M does not use instruction injecting.
Remove the wrong code.
The change was originally a part of http://openocd.zylin.com/4862
It is now re-submitted as #4862 is not ready.
Change-Id: If91cd91d1b81b2684f7d5f10cf20452cde1a7f56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5874
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Consolidate low level register read/write.
Floating point registers were handled by target_read/write_u32
unlike other registers handled by cortexm_dap_read/write_coreregister_u32
There is no reason to do so in cortex_m.
Remove cortexm_dap_read/write_coreregister_u32
and use cortex_m_load/store_core_reg_u32 directly.
Similarly HLA adapters register read/write interface supports all registers
so use it for any floating point and other registers.
Change-Id: Ida679e5f4fec02d94ffb0bd3f265ed7ed2221cdc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5864
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move primask/basepri/faultmask/control packing/unpacking from
cortex_m.c and hla_target.c to armv7m.c armv7m_read_core_reg()
and armv7m_write_core_reg() where also the FP 32/64-bit registers
conversion takes place.
Introduce a new hidden register ARMV7M_PMSK_BPRI_FLTMSK_CTRL
for packing/unpacking of special registers in the register cache.
The new packing/unpacking is endianess safe.
While on it improve returned error codes and LOG_ messages.
Just minimal changes in cortex_m.c and hla_target.c, will be
consolidated in the next patch.
Change-Id: Id51e764e243e54b5fdaadf2a202eee7c4bc729fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Define a new enum with DCRSR.REGSEL selectors.
Introduce armv7m_map_id_to_regsel() to unify mapping in one place.
Use DCRSR.REGSEL selectors for low level register read/write.
Change-Id: Ida0ccdfa9cdb1257a1900b8bfbf172b076374d39
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
When the core is in sleep mode, the core is no longer retiring
instructions. Cortext M remains in "unknown" state. This patch converts
sleep mode to "running" state.
Change-Id: I1e9b6c9be51fd0f1f6ce81af9b1f5f9f1f43c661
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5921
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Functions that are not used outside the file should be declared as
static.
Change-Id: Ie81f6bdce91e2a1456364b47f30aa4d35c7ee7bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5900
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
The Cortex-M implementation of profiling contains a bunch of
conditionals and checks to handle both chips which have PCSR and chips
which do not. However, the net effect of the non-PCSR branches is
actually exactly the same as what target_profiling_default does. Rather
than duplicating this code, just detect the situation where PCSR isn’t
available and delegate to target_profiling_default.
Change-Id: I1be57ac77f983816ab6bf644a3cfca77b67d6f70
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Bit 2 of control register is used if the processor includes the FP
extension
Change-Id: Ie21bc9de8cae5bad9d841e1908eff3aa0bb29d4b
Signed-off-by: Sylvain Chouleur <schouleur@graimatterlabs.ai>
Reviewed-on: http://openocd.zylin.com/5853
Reviewed-by: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If a target is not examined, command vector_catch crashes while accessing
the debug_ap NULL pointer.
maskisr and reset_config commands don't require this check.
Change-Id: I949b6f6e8b983327dd98fbe403735141f8f0b5d6
Signed-off-by: Daniel Trnka <daniel.trnka@gmail.com>
Reviewed-on: http://openocd.zylin.com/5813
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tomas Vanek
Antonio Borneo
Andreas Fritiofson
Tarek BOCHKATI
Yasushi SHOJI
Tarek BOCHKATI
Marc Schink
Kevin Yang
Christopher Head
Sylvain Chouleur
Daniel Trnka