When looking for a debug base address of a core, one should search
through all the ROM tables, not just the top-level one.
This code also assumes that the first found entry (in a depth-first
search) will correspond to core 0, the second to core 1 etc.
The patch is supposed to be an alternative implementation of
http://openocd.zylin.com/#/c/1313/.
Change-Id: Ifc88971a02fe3d9c00d9bf72a822ade5804d4e09
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code treats registers that are shadowed in FIQ mode in a special
way: to read them out the target is first switches to USR mode. But
since USR != ANY the current implementation later skips register read,
and the loop becomes endless in case any !valid ARM_MODE_ANY is
present at the moment arm_dpm_full_context() is called. This was
reported in https://sourceforge.net/p/openocd/tickets/76/. The issue
surfaced because 2efb1f14f6 added two
ARM_MODE_ANY registers ("sp" and "lr") which were not normally read,
so at the time a user was calling "arm reg" they were not valid.
Fix this by changing the mode appropriately while keeping the "mode"
variable state intact so it would later match register's mode.
Compile-tested only.
Change-Id: I01840e8fa20ec392220138a3f1497ac25deb080a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
This was very helpful when debugging programs during async loading.
Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Using custom build-time tools is always more problematic, especially
for cross-compiling.
This alternative implementation assumes "od" (IEEE Std 1003.1-2001)
and sed are available which should be the case for any reasonably
modern system.
Change-Id: I0208f475648c78e7dca127ff4bab60d314b2bf53
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2139
Tested-by: jenkins
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If load_image address overlap with fast_data_area,
it will caouse different mysterius issues. This patch
should prevent it.
Change-Id: Ibc95e5aa3ac002a59755029496b6a72616e9287f
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1854
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A previous commit changes the target name used by tcl scripts.
commit d9ba56c295
target: rename cortex_a8 to cortex_a
The current change renames target functions and definitions in the
implementation from cortex_a8 to cortex_a.
This prepares the implementation to support Cortex-A8, A9, A15-MPCore
in one place.
Change-Id: I73b5a38a92c12ba5bd3b806fbbb664817575a6d7
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1599
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Polling was disabled based on global variables jtag_trst and jtag_srst
which were never touched in non-JTAG mode. Modify the check and remove
the ugly workaround to avoid calls to a possibly uninitialized JTAG
subsystem.
Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2143
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also align them with spaces instead of tabs.
Change-Id: I1c01412a3ea77b29e8e133f5c92d05ed79d7c0f3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2133
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only
setting that is guaranteed to be implemented, as well as being the reset
value in ADIv5.0.
Thus it makes no sense supporting anything else.
Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2132
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Name of the function is already a part of the LOG_DEBUG macro, so
there's no need to include it in the string itself.
Change-Id: I18c3d5b746e9106d55104e490ccf5bc5e85cc380
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2138
Tested-by: jenkins
SAM4L requires additional steps to be taken right after SYSRESETREQ is
issued in order to function robustly:
- CMSIS-DAP DAP driver needs to explicitly check for sticky bit
errors since it is possible for adapter to perform successful
write opration, report no errors and then, under the hood, do
some other things that will result in sticky bit being set.
- Debugger needs to wait for security system to finish
intialization and assert CDBGPWRUPACK before proceeding
This change is related to commit http://openocd.zylin.com/#/c/1995/
Change-Id: I741c95a809bfd60d930cec9482239e4796a62326
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2088
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
We don't need to do full blown AP ABORT in case of CMSIS-DAP errors,
and the code that was in place was not doing that(issuing AP ABORT)
anyway.
Change-Id: Ide83b1f8875d725da6cb0d53aae8229f8c6316b3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2112
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Swd_queue_ap_abort should set DAPABORT, not only clear sticky errors.
However, DAPABORT should not be set as soon as there is a single
FAULT/WAIT response. It's an "emergency only" operations for use only when
the AP have stalled the transfer for a long time. So these need to be
separate functions.
Change-Id: I37618447884faad54d846c2b07fa668ad505919d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1956
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These features are not currently used so remove or disable them before
something starts to. Not having them around simplifies redesign of the
APIs.
Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1955
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Increases performance by a factor of two for long reads.
Change-Id: I81a7a83835058560c6a53a43c3cc991100f01766
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1954
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Otherwise it breaks SWD targets. The check seems really weird anyway since
it loops through *all* TAPs after the ADIv5 target but doesn't do anything
at all with the result, other than not setting the return values despite
returning ERROR_OK.
Remove a bogus initialization that was needed because of the odd
behaviour of this routine when an IDCODE wasn't found.
Change-Id: Ic086352f6af868b3406b00420291a0a671e3acac
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1953
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix bug in parity calculation macro.
Cache and update the selected DP bank when necessary.
Add aborts when the Ack code signals a failure (we should really only
clear the sticky bits, but this will do for now).
Change-Id: I38a4da136ba1d9e989b33c1875a80c0b1b2be874
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1950
Tested-by: jenkins
while investigating coresight components, i've found some new partnumbers and devtypes.
Change-Id: Ie68032b0b21d542c2084f80db38b06f5cd4c7591
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/2166
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On a processor with caches, when you write data to memory OpenOCD invalidates
the cache lines affected. If you write to an address within 64 bytes of
UINT32_MAX, then the for loop control variable wrapped around resulting in an
infinite loop. Change control variable to be an offset from the address
involved. We should never be asked to write 2^32 bytes, so wraparound should
not be a problem.
Change-Id: Ibfe654113eff71684862ff651e7a1cd05ccc6760
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2126
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We don't need to swap the endianness in the target generic code.
This swap is necessary because of the adv_debug_if debug unit.
This patch moves this specific piece of code from or1k.c to
or1k_du_adv.c.
Change-Id: I3acea092fe6edfa79b4a87861b5f01204f071bf0
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1663
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
ARMv7-R cores are largely uniprocessor-configured, and when they are
multiprocessor-configured the format of the MPIDR register isn't
compatible with ARMv7-A cores.
Change-Id: I024ec514496fbab5075c6fb34b6acd870e68e1fc
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2096
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Configuration commands assume the last created target is the one they
should be applied to. An example of this is sourcing an stm32f1.cfg
several times to access several microcontrollers on the same JTAG chain
where cortex_m reset_config should apply to the target that was just
created, not to the first one.
This fixes http://sourceforge.net/p/openocd/tickets/71/ .
Change-Id: I1ca41cc05fe5f36c4bc62dde4614da1405754fd8
Reported-by: Michael Eischer <mieischer@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2142
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If polling was failing, it likely meant that either the target was
disconnected or rebooted. In the latter case it needs to be reexamined
to be properly configured for the debug session, so do it just in
case.
Reported-by: Tim Sander <tim@krieglstein.org>
Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I5b067c18d9276d4e86cc59739f196ae7d0931622
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2151
Tested-by: jenkins
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move logging for cmsis_dap_queue_ap_read/write to happen after a call
to cmsis_dap_ap_q_bankselect so that that SWD operation would appear
in the log in the same sequence they happen on the bus.
Change-Id: Ic046bc753e661da7924b019c9100d6932fb686bf
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2087
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Previous to this commit 'ahbap_debugport_init' would ignore if timeout
happened or not when waiting for CDBGPWRUPACK and CSYSPWRUPACK and would
continue initialization regardless. It also would not reset the
timeout counter after finishing polling for CDBGPWRUPACK and starting
for CSYSPWRUPACK which could potentially cause some problems.
Also refactor code of both snippets into a more generic function to
avoid duplication.
Change-Id: I16e4f50e6819e08c4126e71ef8cec7db559d608e
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2086
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Fix for LOG format specifiers, this is a superset of those
exposed by the arm-none-eabi build.
Add 0x prefix for all values printed in hex.
Add LOG messages for error cases when enabling or disabling
paging.
Change-Id: I070c556e0ad31204231a2b572e7b93af22a9bc61
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2149
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b
Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is only the basic code proposed for mips32_pracc_exec() function.
It checks every pracc address against the expected address when
reading (instruction fetch).
The code expects to start at PRACC_TEXT and any subsequent read address
is obtained by adding 4 to the previous one.
After shifting out all the instructions the code executes a final check.
It checks now for the first pass trough PRACC_TEXT and shift out
only NOP instructions.
A mips core does not need an additional NOP and after the first check
it exits if there is no store access pending.
After shifting out one NOP the core must be reading at pracc text or the
code exits with error.
The code continues shifting out NOPs until all store accesses have
been performed.
After shifting out 10 NOPs it exits with error.
No assumption is made about the number of store instruction shifted out or
the ordering of the store accesses. It only checks that the number of
store accesses is the same as the number of store instructions at dmseg
after execution.
mips32_pracc_read_ctrl_addr() and mips32_pracc_finish() are added to
simpify a bit the code. Fields pa_ctrl and pa_addr are added
in ejtag_info for storing values of pracc control and address.
Change-Id: If6322d5c8cbeadcd4acd3972c0f72c8490f53c34
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1827
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is the first patch intended to make a more precise pracc check
when running in legacy mode (code executed by mips32_pracc_exec()).
It only makes some cleanups, mostly due to unnecessary code.
With the last cache optimizations for processor access (pa for short)
all the pracc functions generate the code following some rules that
make pa more easily to check:
There are no load instructions from dmseg. All the read pas are
instruction fetches. PARAM_IN related stuff is not needed.
Registers are restored either from COP0 DeSave or from ejtag
info fields. PRACC_STACK related stuff is not needed any more.
The code starts execution at PRACC_TEXT and there are no branch or jump
instruction in the code, apart from the last jump to PRACC_TEXT.
The fetch address is ever known.
For every store instruction to dmseg the function code sets
the address of the write/store pa.
The address of every store pa is known.
Current code ends execution when reading a second pass through PRACC_TEXT.
This approach has same inconveniences:
If the code starts in the delay slot of a jump it makes a jump
to PRACC_TEXT after executing the first instruction. A second pass
through PRACC_TEXt is read and the function exits without any warning.
This seems to occur sometimes when a 24kc core is halted in the delay
slot of a branch.
If a debug mode exception is triggered during the execution of a
function the core restarts execution at PRACC_TEXT. Again the function
exits without any warning.
If for whatever reason the core starts fetching at an unexpected
address the code now sends a jump instruction to PRACC_TEXT, but due
to the delay slot the core continues fetching at whatever address + 4
and a second jump instruction will be send for execution. The result
of a jump instruction in the delay slot of another jump is
UNPREDICTABLE. It may work as expected (ar7241), or let the core in
the delay slot of a jump to PRACC_TEXT for example. This means the
function called next may also fail (pic32mx).
Change-Id: I9516a5146ee9c8c694d741331edc7daec9bde4e3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1825
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Near all pracc functions store $15 in DeSave and
restore it when exiting.
There is no need to save it, if mips32_pracc_read_regs()
save this register in Desave when entering debug mode.
mips32_pracc_write_regs() needs to update it when
exiting debug mode.
Other pracc functions must not modify DeSave.
The jump code in the fastdata transfer function needs also
some little modifications.
Remark:
Like in current code the user can read/modify $15
with the cp0 31 commands.
Change-Id: I5b7dfc1b6169da846f5d2dd3ad4209a9da2c3fad
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1565
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>