By saving a pointer to the tail of the list,
we don't need to traverse the entire command
queue before we're able to append an item to
it.
With this patch, I see a 10% improvement when
using the embedded XDS100v2 on AM437x IDK board
to load a 4MiB binary (linux zImage) to DDR
with load_image.
IOW, we went from ~305kB/sec to ~336kb/sec.
Change-Id: Idb55d49f0d0106043374ab520b2f3b6b32f2c50f
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2709
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Daniele Emancipato <daniele12457@hotmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The svf_progress_enabled variable is global, hence its lifetime is not
limited and it retains the value from the previous run. Fix this by
explicit assignment.
Change-Id: Id6f4fa88f39521606342a37f6876a0948ac5406e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3111
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This makes SVF error output match actual line numbers in the file
processed.
Change-Id: I1fa4b9d0891e4358b7beada516945d5331ebe182
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2945
Tested-by: jenkins
Kinetis driver checks MDM STAT register to detect secured state of MCU.
An unsecured clean device typically triggered a huge fat alarm message.
Now when driver detects secured state it tries to halt MCU and then
re-reads status register.
Command "mdm mass_erase" used to deassert reset when finished
and MCU started looping in hard fault - WDOG reset cycle.
Now "reset halt" is issued. Clean flash is not run after mass_erase.
Change-Id: I23f393509fbd8751d44ffc744ff2d67f1074f74e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3010
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
SAMD driver suffered from following problems:
1) Flash was erased as an integral part of flash write.
It was not documented so with usual workflow it resulted
in erasing flash twice (and reducing flash lifespan)
and in almost double flashing time.
2) Sector erase was silently skipped if "is_erased" flag was set.
"is_erased" logic was not reliable, e.g. when a row write
was aborted after successful write of some pages, sector was
still considered as erased. "is_erased" flag could not
cope with flash writes from a user program.
3) Writing of a block with start address unaligned to a flash page
resulted in failed assert and OpenOCD abort.
4) Disabling cache in bit 18 of 16-bit halfword never worked.
MCU implements cache invalidate in hardware so there is no need
to take care about. This bug was reported by Tony DiCola.
New code does not erase flash in write operation.
Instead it traditionally relies on erasing flash beforehand.
"is_erased" logic and cache disabling is completely removed.
It simplifies write procedure a lot and flash write is now faster.
The change partly solves ticket #109 SAMD/SAM4L driver doubles flash erase.
Change-Id: I582b497d01a351575533a1f8c9810a4413be0216
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3045
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds support for the Atmel SAML21 variant B parts.
There is minimal change between the two variants, but in
variant B the automatic page write which the at91samd flash
driver relies on to be enabled is disabled by default.
With this patch the write row function will now issue a page write
command after each of the four pages in the row if the MANW (manual
write) bit is set. This also fixes flash write for the SAMC20/SAMC21
devices which have the MANW bit set by default as well.
I have also moved the device ID (DID) register bitfield extraction
from the find_part into helper macros. These can be used in the future
if there are more workarounds for specific devices.
Tested (programming) on:
ATSAML21-XPRO
ATSAML21-XPRO-B
SAMC21 Xplained Pro
SAMD21 Xplained Pro
SAMD20 Xplained Pro
Change-Id: I401a8aa1efd64730840c0d62cf49a1e880ea5900
Signed-off-by: Andreas Loehre <alohre@gmail.com>
Reviewed-on: http://openocd.zylin.com/2903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cmsis-dap protocol has both DAP_Connect and DAP_Disconnect commands.
Logically if cmsis_dap_swd_switch_seq() calls DAP_Connect in connected
state it should call DAP_Disconnect first.
Doing so surprisingly solves problems on Atmel EDBG with target SAMD/R/L/C.
Without this change SWD communication breaks after reset run/halt
in config "reset_config srst_only" and reconnect trials repeatedly
fail with "SWD ack not OK: 0 JUNK"
Change-Id: Ie951098d5e0c83f388e2df414608aaabec2135c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to Infineon, XMC4500 EES AA13 with date codes before GE212 -
as seen on an XMC4500 General App Kit - had a zero SCU_IDCHIP register.
Handle this by extending our checks to not error out on zero SCU_IDCHIP
and by printing a useful info string in that case.
Change-Id: Ic2d641a314627dd5a1ff775a0113999191b95e3d
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2751
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 68101e67ac introduced a
regression which resulted for ever-growing registers list (as output
by "reg" command), its contents were doubled every reset (actually,
every examination).
Change-Id: Ie3409c795160a2fc840a5e8a892928df0bcc0c57
Reported-by: Daniele Emancipato <daniele12457@hotmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3100
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch brings the calculation of the address ranges handled by
ttbr0 and ttbr1 registers in line with ARM DDI 0406C, Table B3-1
Change-Id: Ib807c4b1cb328a6f661e1a0898e744e60d3eccac
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3006
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If ttbcr is changed after the debugger has examined a target for the
first time, address translations may fail. This problem does not show up
with Linux because it doesn't use ttbr1, but it shows with other OS that
use this feature. If the debugger connects to the target while it's in
u-boot, all address translations will fail after the OS has booted and
the target can not be debugged.
This patch reads the ttbcr in armv7a_mmu_translate_va() and compares it
a cached value. If a difference is detected, armv7a_read_ttbcr() is called
to re-parse the ttb configuration and update the cache.
Change-Id: I1c3adf53ea9d748a0e1e3091d9581e5c43ed64e8
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3005
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
kinetis_write() with byte count not divisible by prog_section_chunk_bytes
computed wrong wc and therefore paded section chunk by some
random data instead of 0xff
Change-Id: Ic7c66d8a3ceacda9e611e98b9fbf943b8001774b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2994
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Kx devices with FTFA flash need the watchdog disabled when programming.
I tried to keep overhead as small as possible and re-use registers that
were already inquired (e.g. sim_sdid).
Change-Id: Ibc29a26ec34102d78a6c3920dd16f63e134a8f6f
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2986
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This makes it easier to relocate the install tree of OpenOCD from where
it was originally built (for example, if put onto a different machine),
without having to change scripts or add something to the command line
every time.
Change-Id: Ia5edf0eba166f7a999f267bd6a92402dab9b399e
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3004
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The memory leak occurs when opening a file fails. It can be
reproduced by using the "flash verify_bank" command with a filename
that does not exist.
Change-Id: I60b7b545c18793d750ff75d08124fde3f0aa6f64
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2998
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If we work on smp system, the output of step command will depend
on Id of default target.
This patch adds additional information to help find what on which
core is happening.
Example of LOG after this patch.
imx6.cpu.1: target state: halted
^^^^^^^^^^
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x60000093 pc: 0x80076c0c
MMU: enabled, D-Cache: enabled, I-Cache: enabled
imx6.cpu.0: target state: halted
^^^^^^^^^^
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x20000193 pc: 0x802ccb6c
MMU: enabled, D-Cache: enabled, I-Cache: enabled
Change-Id: I536a2cce33b5ab10af9de2a43b9960320c17729f
Signed-off-by: Oleksij Rempel <external.Oleksij.Rempel@de.bosch.com>
Reviewed-on: http://openocd.zylin.com/2691
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A segmentation fault in cortex_m_endreset_event() is sometimes raised
with very broken target like Kinetis Kx with erased flash and active WDOG.
Debugging revealed that cortex_m->dwt_num_comp is 4 and
dwt_list is NULL at cortex_m:290
Change-Id: I229c59d6da13d816df513d1dbb19968e4b5951e2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2989
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Memory for the symbol table was allocated by malloc but not initialized other
than with the symbol name. Therefore `address` and `optional` members were
having arbitrary values leading to every symbol being optional most of the
time which messes up RTOS auto-detection. Memory will now be zero-initialized
as in other RTOS implementations.
Change-Id: I6c6e31ec1ef7e043061adf8c695b2139620e005d
Signed-off-by: Daniel Krebs <github@daniel-krebs.net>
Reviewed-on: http://openocd.zylin.com/3017
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
According to "man 2 poll" the correct header to include is poll.h, not
sys/poll.h. Reported by a build against musl.
Change-Id: I5298b49dc947d1a368e423104c0c0c7b9bdd1a10
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2947
Tested-by: jenkins
In the case that the STKALIGN bit is set on Cortex M processors, on
entry to an exception - the processor can store an additional 4 bytes
of padding before regular stacking to achieve 8-byte alignment on
exception entry. In the case that this padding is present, the
processor will set bit (1 << 9) in the stacked xPSR register. Use the
new calculate_process_stack callback to take into account the xPSR
register and use it on the standard Cortex_M3 stacking.
Note: Change #2301 had some misinformation regarding the padding. On
Cortex-M the padding is stored BEFORE stacking so xPSR is always
available at a fixed offset.
Tested on a Cortex-M0+ (Atmel SAMR21) board which has STKALIGN fixed
to a '1' such that this alignment always occurs on non-aligned stacks.
Behavior of xPSR verified via the (bad-sorry) assembly program below by
setting a breakpoint on the SVC_Handler symbol. The first time
SVC_Handler is triggered the stack was 0x20000ff8, the second time
SVC_Handler is triggered the stack was 0x20000ffc. Note that in both
cases the interrupt handler gets 0x20000fd8 for a stack pointer.
GDB exerpt:
Breakpoint 1, 0x000040b6 in Reset_Handler ()
(gdb) hbreak SVC_Handler
Hardware assisted breakpoint 2 at 0x40f8
(gdb) cont
Continuing.
Breakpoint 2, 0x000040f8 in SVC_Handler ()
(gdb) print $msp
$3 = (void *) 0x20000fd8
(gdb) x/9w $msp
0x20000fd8: 0x1 0x2 0x3 0x4
0x20000fe8: 0x88160082 0xa53 0x40ce 0x21000000
0x20000ff8: 0x0
(gdb) cont
Continuing.
Breakpoint 2, 0x000040f8 in SVC_Handler ()
(gdb) print $msp
$4 = (void *) 0x20000fd8
(gdb) x/9w $msp
0x20000fd8: 0x1 0x2 0x3 0x4
0x20000fe8: 0x88160082 0xa53 0x40e8 0x21000200
0x20000ff8: 0x0
Assembly program:
.cpu cortex-m0plus
.fpu softvfp
.thumb
.syntax unified
.section .vectors
@ pvStack:
.word 0x20001000
@ pfnReset_Handler:
.word Reset_Handler + 1
@ pfnNMI_Handler:
.word 0
@ pfnHardFault_Handler:
.word 0
@ pfnReservedM12:
.word 0
@ pfnReservedM11:
.word 0
@ pfnReservedM10:
.word 0
@ pfnReservedM9:
.word 0
@ pfnReservedM8:
.word 0
@ pfnReservedM7:
.word 0
@ pfnReservedM6:
.word 0
@ pfnSVC_Handler:
.word SVC_Handler + 1
.section .text
.global Reset_Handler
Reset_Handler:
cpsie i
ldr r0, .stack_start
ldr r2, .stack_last
eors r1, r1
.loop_clear:
str r1, [r0]
adds r0, r0, #4
cmp r0, r2
bne .loop_clear
subs r2, r2, #4
mov sp, r2
movs r0, #1
movs r1, #2
movs r2, #3
movs r3, #4
svc #0
ldr r0, .stack_start
ldr r2, .stack_last
eors r1, r1
.loop_clear2:
str r1, [r0]
adds r0, r0, #4
cmp r0, r2
bne .loop_clear2
mov sp, r2
movs r0, #1
movs r1, #2
movs r2, #3
movs r3, #4
svc #0
.loop:
b .loop
.align 4
.stack_start:
.word 0x20000f00
.stack_last:
.word 0x20000ffc
@ first call - 0x2000fff8 -- should already be aligned
@ second call - 0x2000fffc -- should hit the alignment code
.global SVC_Handler
SVC_Handler:
bx lr
Change-Id: Id0940e6bbd6a59adee1378c0e86fe86830f0c8fc
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Cc: Evan Hunter <evanhunter920@gmail.com>
Cc: Jon Burgess <jburgess777@gmail.com>
Reviewed-on: http://openocd.zylin.com/3003
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some targets (Cortex M) require more complicated calculations for
turning the stored stack pointer back into a process stack pointer.
For example, the Cortex M stores a bit in the auto-stacked xPSR
indicating that alignment had to be performed and an additional 4
byte padding is present before the exception stacking. This change
only sets up the framework for Cortex-M unstacking and does not
add Cortex-M support.
Note: this also fixes the alignment calculation nearly addressed by
change #2301 entitled rtos/rtos.c: fix stack alignment calculation.
Updated calculation is in rtos_generic_stack_align.
Change-Id: I0f662cad0df81cbe5866219ad0fef980dcb3e44f
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Paul Fertser <fercerpav@gmail.com>
Cc: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Cc: Evan Hunter <evanhunter920@gmail.com>
Cc: Jon Burgess <jburgess777@gmail.com>
Reviewed-on: http://openocd.zylin.com/3002
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Intel is relicensing our contributions to OpenOCD under GPL
version 2 or any later version. We previously contributed code
under GPL version 2 only. It was not our intention to differ
from the standard OpenOCD license. We're correcting that here.
This also applies retroactively to previous versions of our
contributions to OpenOCD.
Change-Id: I5e831ed95d03d2044d8e5a8375b21c6e52c933d7
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3044
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
K22FN1M0 and K22FX512 has FTFE flash and old style SDID.
K22FN128, 256 and 512 has FTFA flash and new style SDID
K63 and K64 detects as K61 and K62, see Errata 1N83J e7534
Change-Id: I2aca6f1f18819bb2b2ec4982036510de444ad2ac
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2867
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Patrick Stewart <patstew@gmail.com>
max_flash_prog_size euals to pflash_sector_size_bytes for most of devices.
There is no point setting max_flash_prog_size for devices without
FS_PROGRAM_SECTOR capability.
Check for zero sector_size to avoid div by zero exception in case of
device has FlexNVM but the driver does not define nvm_sector_size_bytes
Change-Id: Iaf4e007fb1ec3d24c373350410e4bebe504a4c3e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2958
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Patrick Stewart <patstew@gmail.com>
The K24 uses the KL-style SDID register and has some flashing quirks, so the kinetis driver does not support it properly.
Extend the chip detection routine to support the new SDID format. Add a parameter for the maximum flash size, as the K24 only supports 1k flashing blocks but has 4k sector size. Remove global 'granularity' array, as it's only really needed in one function. Replace 'klxx' with an enum showing which flash commands are actually supported on a given chip.
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Change-Id: Ie244fab564d58c5cfe4fa36a025f0b2674ffad69
Reviewed-on: http://openocd.zylin.com/2864
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I3cf5ced568319878b8bf40743e4c07718f630c68
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2953
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Flash driver "mini51.c" and "nuc1x.c" are same target MCU.
This patch integrates each driver and functions,
and makes into new "NuMicro" flash driver.
Change-Id: Ifff5c1cfdd265acca0f489631695be9194fa144c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A target config and a simple flash driver for the ADuCM360 microcontroller.
The EEPROM of the chip may be erased and programmed.
Change-Id: Ic2bc2f91ec5b6f72e3976dbe18071f461fe503b8
Signed-off-by: Ivan Buliev <i.buliev@mikrosistemi.com>
Reviewed-on: http://openocd.zylin.com/2787
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
The problem was reported by jstefanop on IRC, the SVF was generated with
Xilinx ISE 14.7.
Found and investigated with Valgrind's vgdb service.
Change-Id: I32b0e77e0380ce4a391661f97449f9c2a5f83625
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2933
Tested-by: jenkins
Currently, the maximum size of a command sent to the TCL server is
4k. This patch increases this limit up to 4M.
Reasoning:
To get high-speed JTAG data transfers, I'm using a very long shift
register. This reduces the overhead of the state changes, as well as the
latency due to the common USB adapter transfers considerably. In order
to submit those long DRSCAN commands to OpenOCD over the TCL/TCL
interface, long TCL command lines are required. This is enabled by this
patch.
v3:
Address review comments. Drop line instead of connection when realloc()
fails.
Changes in v2 of this patch:
The line buffer is allocated dynamically to avoid an OpenOCD memory
overhead if the large buffers are not used. The buffer starts at 4K and
increases exponentially up to 1M, and then linearly in 1M increments up
to 4M.
Change-Id: Iecaef6a56ed5e18e9de4d912a514031ea78fa3bd
Signed-off-by: Philipp Wagner <philipp.wagner@tum.de>
Reviewed-on: http://openocd.zylin.com/2837
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add constant CONNECTION_LIMIT_UNLIMITED which indicates a service
has no connection limit
Change-Id: I008d31264010c25fa44ca74eb6d5740eca38bee1
Signed-off-by: Austin Morton <austinpmorton@gmail.com>
Reviewed-on: http://openocd.zylin.com/2937
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Problem
As my compiler has "warnings being treated as errors" on, it shows the
error message:
error: 'retval' may be used uninitialized in this function
Investigation
Nothing wrong with the logic, 'retval' would have a value before returning.
Just wanna get rid of the compiling "warning as error" message.
Solution
Provide a reasonable default value
Change-Id: I712c15f82819c6c48bee9dceca8de4b18aeb29b0
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2905
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
During reallocation a new memory region might be allocated and the old
one freed. If jtag queue is holding a pointer to the old memory, it will
segfault during the execution. Avoid this by flushing the queue before a
reallocation attempt is made.
This should fix ticket #102.
Change-Id: I737fc3f1ebf6d76413a475beb8bf20184fe0233f
Reported-by: Alex Forencich <aforencich@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2899
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the chip IDs corresponding to the new 5V "SAMC" parts which are
otherwise identical to the SAMD and should work with this driver. Also
add the configurations for their Xplained Pro boards.
Change-Id: Ic268d4ac384a3a77d4211a94da9f9faf4d8c0f7b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2809
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes a warning as reported by the current clang version:
../../../../src/flash/nor/sim3x.c:867:20: error: address of array
'sim3x_info->device_package' will always evaluate to 'true' .
Change-Id: Ie160cbe6df8f491e9beff38d47e2f13575529bf9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2838
Tested-by: jenkins
Reviewed-by: Oleksij Rempel
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only read access to flash chips so is through the target's
memory. Flashes like jtagspi do not expose a memory mapped interface
to the flash. These commands use the flash_driver_read() driver API
directly.
Change-Id: I40b910de650114a3f676507f9f059a234377d862
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2842
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds an option to disable the use of the JSTART instruction
when loading bitstreams to xilinx fpgas. JSTART apparently prevents
configuration if the startup clock is not set to the jtag clock in
the bitstream.
xc3sprog is omitting JSTART for all devices. Problems with loading a bitstream
that does not have StartupClk:JTAGClk are described here:
http://www.xilinx.com/support/answers/56151.html
Change-Id: I8137c0bae05a8c3c6f8e2611869f70a770d1651d
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The testee target is usefull for certain non-cpu pass-through
situations, for example in the case of a spi flash mapped to the DR of
a JTAG tap, as is the case for most FPGAs with SPI flashs behind them.
We just manage the RUNNING/RESET/HALTED state in the testee driver to
support it being halted which is a requirement for flash banks.
Change-Id: I1b4d52c58a1f6bd753e126bfde74dcc5164d7b69
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2840
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add USB VID and PID for the J-Link interface running on the Nordic
Semiconductor nRF51-DK. Also tested with debug out port to debug
external boards.
* Elimiantes need for `-c "jlink pid 0x1015"` on the openocd cmd line.
Change-Id: Ib23acb72b9f5183b76fc7dc22b556982869ae830
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Reviewed-on: http://openocd.zylin.com/2775
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ThreadX uses two stacking schemas on ARM926E-JS, extend API to use more then
one stecking at time.
Change-Id: I92d445ad0981b6409ea4c4e7e438d3a7ae39cbe7
Signed-off-by: Alexander Drozdov <adrozdoff@gmail.com>
Reviewed-on: http://openocd.zylin.com/2848
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
MMU types were checking and installing fakes at init, but this wasn't catching
all devices. Fixes segfaults when attempting mdw and friends on avr.
Change-Id: I5b11f9913157a21f1aeb11ec852f593b529d9be8
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2791
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Even though the latest firmware version for stlink-v1 supports "v2"
JTAG API, the hardware SRST handling is still broken; amend the check
accordingly.
Change-Id: I62c662cd7aa209d2d6e9fe260f5c0be81d0ce672
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2761
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the identifiers to support the flash on the Cypress Type-C Port Controller
chips of the CCG1 family : http://www.cypress.com/ccg1/.
Tested successfully on CYPD1132-16SXI.
Change-Id: I3fe6283379e5bcab964afac31b547ef95535aa2c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://openocd.zylin.com/2757
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The notation Gx0 in the nRF51 Series Compatibility Matrix indicates that
the specified HWID is valid only for build code 0 of each chip, and for
subsequent builds the HWID will be different. Replace the Gx0 notation
with G0 throughout, and add the missing HWID for nRF51422 QFAC A1
(present on the newer nRF51 developer boards).
See: https://www.nordicsemi.com/eng/nordic/download_resource/41917/5/55913589
See: https://devzone.nordicsemi.com/question/30774/mapping-hwid-to-revision-information/
Change-Id: I79d842137d41342db35904867c48b06fbc6fbc70
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2593
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since mqx comes last in the list, with the auto option its
update_threads is called even though it wasn't detected.
This check should be removed from all the rtos helpers and moved to
the generic code, but better do it later all in one go.
Change-Id: If24ab42a58a468d90e9f12028d4c2fb76a9bc2e8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2741
Tested-by: jenkins
It was observed on AM437x that after every reset the target's debug
regions are unpowered. To be able to properly communicate with the
target and perform cortex_a init debug access after a reset event the
examination need to be performed every time, not just on OpenOCD
start.
Change-Id: Idf272e127ee88341e806ee00df154eade573451d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2723
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
After intermittent connection failures or target power failures it
might be necessary to try reexamination even when polling fails. This
should make communication with Cortex-A targets more reliable.
This was runtime tested with stlink attached to an stm32l1 and an FTDI JTAG
adapter attached to an stm32f1 target.
Change-Id: I38c4db8124b7f4bbf53ddda53c13273449f49c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2721
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Färber <afaerber@suse.de>
This adds support for the new Atmel SAML21 family of low-power Cortex
M0+ devices. Their Flash controller is essentially the SAMDxx one so
the change consists of adding the new part IDs. Unfortunately the
device ID logic had a couple of mistakes in it that did not affect
anything on SAMD2x devices (due to 0 values expected there) but that is
a problem on L21, it's therefore addressed here and things should now
match the datasheets.
Tested on Amtel SAML21 Xplained Pro development kit against the included
SAML21J18A there. Also tested for regressions on a SAMD20 and SAMD21
using their dev kits.
Change-Id: I768f75e064b8656c15148730dacaa4c3acfc4101
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2690
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the mandatory Info documentation for the driver as well as
the usage field.
As a clean up, this also includes freeing of the allocated memory
which results in a memory leak if probe is invoked multiple times.
Valgrind-tested.
Reported by Dmitry Shpak.
Change-Id: I2b1d9b9e8b069c6665b11d880b40ce19a1b26ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2694
Tested-by: jenkins
Reviewed-by: Дмитрий Шпак <disona@yandex.ru>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch was tested with an EZR32WG Starter Kit.
Change-Id: I0f7c619e715fe30e88e6da3bead0806dd3bce819
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2700
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Run-time tested with FreeRTOS V8.1.2 (current version).
For the time being I propose this way of dealing with RTOSes that do
not export necessary information on their own.
I also suggest implementing a similar scheme for ChibiOS, exporting
the necessary struct fields' offsets via an OpenOCD-specific helper.
Change-Id: Iacf8b88004d62206215fe80011fd7592438446a3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2347
Tested-by: jenkins
xSuspendedTaskList and xTasksWaitingTermination are only available for
some configurations. Missing optional symbols will have their addresses
remaining at zero so the corresponding lists will be skipped when
building the task list.
Change-Id: If330f5038d009298c3a14a4d2756db7105a30bc8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2425
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a remake of http://openocd.zylin.com/1966
originally written by Angus Gratton <gus@projectgus.com>
ATSAM4L has a "System Manager Access Port" (SMAP) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Without this change any use of sysresetreq or srst locks the chip
in reset state until power is cycled.
A new function smap_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and SMAP reset is released then.
Change-Id: Iad736357b0f551725befa2b9e00f3bc54504f3d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2604
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some targets need arbitrary amount of time (usually not too long)
after reset (both sysresetreq and srst) to do initialisation, and
SWD/JTAG is not available during that. According to PSoC4 docs, the
debugger should try connecting until it succeeds.
Also ahbap_debugport_init might be necessary to perform after using
hardware srst too, so add it there (except for the targets that
support srst_nogate since they are very unlikely to need it).
Change-Id: I3598d5ff7b8e0bf3a5566a57dec4b0b2b243d297
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2601
Tested-by: jenkins
In some cases (the most obvious are TI's SoCs) ROM table lacks entries
for the cores, so OpenOCD has no way to determine what debug base to
use. Due to an error fixed in ec9ccaa288 it wasn't handled properly,
and OpenOCD would continue to try using dbgbase = 0, which happened to
work for e.g. AM437x.
This patch adds a clear indication to the user that to access such a
target, dbgbase must be set manually in the config.
Reported by Felipe Balbi on IRC.
Change-Id: Id8533e708f44b76550eb8b659564f5f45717c298
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2603
Tested-by: jenkins
In some circumstances (e.g. inappropriate jtag clock)
target_write_memory in lpc2000_iap_working_area_init might fail. The
allocated working area should be freed inside
lpc2000_iap_working_area_init in this error case.
This was leading to a weird segfault due to stack corruption later
when reset was executed.
Reported by quitte (Jonas Meyer).
Change-Id: Ia2ed42a9970a4d771727fd516a6eea88e9b859e2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2696
Tested-by: jenkins
Calling ahbap_debugport_init() is wrong here because the actions
performed by it might lead to jtagdp_transaction_endcheck errors thus
leading to infinite recursion.
The removed code is not needed now because target polling should lead
to reexamination automatically, and both cortex_a and cortex_m call
ahbap_debugport_init() as part of their target examine handler.
This was reported as a real life issue on IRC by Weaselweb with
Cortex-A target. Quitte reports similar results in some circumstances
(adapter_khz too high) with LPC17xx.
Change-Id: I7148022f76a1272b5262d251f2e807ffb1543547
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2697
Tested-by: jenkins
The IAP working area needs to be freed here, just like in all the
other driver functions since an automatic local variable is used to
store a pointer to it.
This was reported by quitte (Jonas Meyer) on IRC as a strange totally
unrelated segfault after doing certain operations (leading to target
reset) from GDB. He has provided me with remote access to the specific
machine and configuration that exposed the issue, and after some
debugging it became apparent that a auto local variable (holding the
gdb connection pointer) gets overwritten somehow. Placing an
appropriate breakpoint just before the event and using a watchpoint
made the cause apparent: reset lead to freeing of all working areas,
and there was one holding a pointer to a variable that was auto local
in get_lpc2000_part_id().
Change-Id: I7e634d890135ca0f3b4b311e09e8385a03982bd6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2695
Tested-by: jenkins
This regression was introduced with d90b86d8. "transport select" doesn't
throw an error anymore and autoselects the first available transport on
its own.
Reported by moyix on IRC.
Change-Id: I3f303c0372e915931cca4b28af450694abc1a63e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2693
Tested-by: jenkins
The detection framework assumes rtos->symbols is dynamically allocated,
an assumption that the ChibiOS variant breaks by providing a raw statically
allocated symbol list.
Change-Id: I379bcc2af99006912608ddd3f646ff7085606f47
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-on: http://openocd.zylin.com/2597
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch might influence openocd Tcl commands behaviour in subtle
ways, please give it a nice testing.
The idea is that if an OpenOCD Tcl command returns an error, an
exception is raised, and then the return code is propogated all the
way up (or to the "catch" if present). This allows to detect
"shutdown" which is not actually an error but has to raise an
exception to stop execution of the commands that follow it in the
script.
openocd_thread special-cases shutdown because it should then terminate
OpenOCD with a success error code, unless shutdown was called with an
optional "error" argument which means terminate with a non-zero exit
code.
Change-Id: I7b6fa8a2e24c947dc45d8def0008b4b007c478b3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2600
Tested-by: jenkins
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Commit a35712a85c caused a regression where command
openocd -c "echo a1; shutdown; echo a2"
always returned non-zero exit status to operating system,
even when commands before shutdown all succeeded. This patch
attempt to fix this.
Change-Id: I3f478c2c51d100af810ea0171d2fd4c8fcc657f3
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-on: http://openocd.zylin.com/2589
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Found by clang static checker.
On the very first call of jim_newtap_expected_id() pTap->expected_ids
and expected_len are null, and there's nothing to copy. This patch
changes this cryptic code to use realloc() instead.
Change-Id: Ic0b5140d08257a906f15b55a2ae64db7bc06d5f1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2562
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Tested-by: jenkins
Current flash driver can fail to write across the sector boundary.
This patch fixes "thisrun_bytes" set to "cmd51_dst_boundary" value instead of "cmd51_can_xxxxb"
Referred to SevenW's post and fix,thanks.
http://sourceforge.net/p/openocd/mailman/openocd-devel/thread/fa32e7d6654df22470dc5f4a3dbc984a%40familiebenschop.nl/#msg33594152
Tested on below listed chips.
LPC810,LPC811,LPC812,LPC824,LPC1115,LPC1343,LPC1347,LPC1227,
LPC1769,LPC1788,LPC54102,LPC4088 and LPC2388.
Change-Id: If1c6a1daa58ca27c405bd959a784e599a7a8f4d4
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2607
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Felipe Balbi
Paul Fertser
Tomas Vanek
Andreas Loehre
Andreas Färber
Jeff Ciesielski
Morgan Quigley
Esben Haabendal
Evan Hunter
Mahavir Jain
Matthias Welwarsky
Thomas Schmid
Jonathan Larmour
Marc Schink
Oleksij Rempel
daniel-k
Maxime Coquelin
Andrew Ruder
Uwe Bonnes
Ivan De Cesaris
Peter A. Bigot
Patrick Stewart
Alex Forencich
Jim Paris
Nemui Trinomius
Ivan Buliev
Philipp Wagner
Austin Morton
Alamy Liu
Christoph Pittracher
Andrey Yurovsky
Robert Jordens
Kyle Manna
Alexander Drozdov
Karl Palsson
Vincent Palatin
Simon Qian
Spencer Oliver
Andreas Fritiofson
Richard Braun
Juha Niskanen
Patrick Noffke