Given that the manual states that these two subcommands are
deprecated and were scheduled to be removed back in 2010,
remove them and the corresponding documentation from the
manual.
Change-Id: Iaac633349d7fcb8b7f964109c7d26dd0cc5fc233
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1860
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Without this patch, to perform a memory read, OpenOCD first issues an
LDC instruction into DBGITR in Stall mode (thus executing the
instruction), then switches to Fast mode and reads from DBGDTRTX once
for each word to transfer.
At the very end of the transfer, the final Fast mode read of DBGDTRTX
has, as always, the side effect of re-issuing the LDC instruction. This
causes two problems:
(1) If the word immediately beyond the end of the requested region is
inaccessible, this spurious LDC will cause a fault. On a fast CPU, the
LDC will finish executing by the time the poll of DSCR takes place,
failing the entire memory read. On a slow CPU, the LDC might finish
executing later, leaving an unexpected and confusing sticky fault lying
around for the next operation to see.
(2) If the LDC succeeds, it will leave the loaded word in DBGDTRTX, thus
setting DBGDSCR.TXFULL=1. The cortex_a_read_apb_ab_memory routine
completes without consuming that last word, thus confusing the next
routine that tries to use DBGDTRTX (this may not have any visible effect
on some implementations, because writing to DBGDTRTXint when TXFULL=1 is
defined as Unpredictable, but I believe it caused a visible problem for
me).
With this patch, the bulk mem_ap_sel_read_buf_noincr is modified to omit
the last word of the block. The second-to-last read of DBGDTRTX by that
function will cause the issue of the LDC for the last word. After
switching back to Normal mode and waiting for that instruction to
finish, do a final read of DBGDTRTX to extract the last word into the
buffer, leaving TXFULL=0.
Without this patch, memory accesses are always expanded such that they
are aligned to the access size. With this patch, accesses are issued
exactly as ordered by the caller. The caller is expected to handle
fragments at the beginning and end of the transfer if the address is
unaligned and an unaligned access is not desired.
Without this patch, the DFAR and DFSR registers, which report the
location and status of data faults, are ignored while performing memory
accesses, which could cause problems debugging an OS page fault handler.
With this patch, DFAR and DFSR are preserved across memory accesses, and
DFSR is decoded in the event of a synchronous fault to provide the
caller with more information about the reason for failure.
Thanks to Boris Brezillon for the original patch whose ideas led to the
non-word access mechanism implemented here and to various code reviewers
for their comments.
Change-Id: I11ae7104fbe69a522efadefc705c9a217a7eef41
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/2381
Tested-by: jenkins
Reviewed-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Convert the DWT register store to use a byte array and fix the byte order
bug uncovered by that. Also fix an incorrect access of the PC value.
Change-Id: Idb5acab71bdf5a96895c358324b05c335e4d32ca
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2476
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The registers are represented as bit arrays intended to be accessed using
the buf_set_* and buf_get_* functions. Storing the register values in
integers enables accessing them directly, which gives different results
depending on host byte order.
Convert the register store to use a byte array instead and fix all the
byte order bugs uncovered by that.
Also merge the 32 and 64 bit register fields. Only one of them is used at
a time and after the change to byte arrays their types are also the same.
Change-Id: I456869a1737f4b4f5e8ecbfc1c63c49a75d21619
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2475
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
On armv7 there no longer are 1kB pages. Instead the bit that in
older architectures distinguished 1kB pages from 4kB pages is on
armv7 used for as execute-never marker. There may now also be 16MB
supersections with 40 bit physical address.
Change-Id: I959bdb8012782a9d07d968907a21f50e3d9b356a
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/2386
Tested-by: jenkins
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add Cortex-A5 identification to ROM-table display, and also
to cortex_a_init_debug_access. This change is mostly cosmetic.
Change-Id: I7b1dd8755d70d45eb5f315aa1918d44a813b3cdf
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/2483
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The image struct is malloc'd and hence base_address_set doesn't have a
defined value.
Caught by Valgrind.
Change-Id: Ice15b2299fc768e44e8034eeb93e035076eacd03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2524
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After profiling gmon.out was being written in little endian format only
which would cause gprof to issue and error and exit on big endian targets.
Change-Id: I526a40adae0f9a439fc5b77cef30fda228198b48
Signed-off-by: Jose de Sousa <jose.t.de.sousa@gmail.com>
Reviewed-on: http://openocd.zylin.com/2168
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also remove an unrelated no-op cast.
Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2473
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This helps to uncover incorrect usage when a pointer to uint32_t is
passed to those functions which leads to subtle bugs on BE systems.
The reason is that it's normally assumed that any uint32_t variable
holds its value in host byte order, but using but_set_u32 on it
silently does implicit pointer conversion to (void *) and the
assumption ends up broken without any indication.
Change-Id: I48ffd190583d8aa32ec1fef8f1cdc0b4184e4546
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The default label does just return the same error code as the case for
zero, so this can be handled by a simple if statement.
Change-Id: I61a8cb51b5e261f21eca386af7d8cbf17ffa2d44
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/2430
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A7 MPCore needs unlocking the debug registers same as with A15 MPCore.
Found out by hacking on the code.
Change-Id: I613cb4fb35007b85b4a9a401577b47768bc1a08b
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-on: http://openocd.zylin.com/2344
Tested-by: jenkins
Reviewed-by: Kamal Dasu <kamal.dasu@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added Cortex-A15 support for DAP AHB-AP init code as per ADI V5 spec.
Also added changes to make the APB MEM-AP to work with A15.
Made the the cortex_a target code generic to work with A8, A9
and A15 single core or multicore implementation. Added armv7a code
for os_border calculation to work for known A8, A9 and A15
platforms based on the ARM DDI 0344H, ARM DDI 0407F, ARM DDI 0406C
ARMV7A architecture docs.
Change-Id: Ib2803ab62588bf40f1ae4b9192b619af31525a1a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1601
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
For example "bp 0x20000000 8 2" makes openocd segfaulting on a
stm32f4x Discovery board.
Change-Id: I1ddd46b1fa9ade78db2234ed975ccefb72539331
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/2342
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GCC-4.2 on Mac/PPC complains about size_t is expected for %zx and the build stops.
In order to avoid other problems, I've chosen simply to typecast.
Change-Id: I99b569c4d1100e729712e31d24d6539f8b5971b6
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2360
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When communication with target fails for whatever reason, it makes
sense to do JTAG-to-SWD (in case the target got power-cycled or the
DAP method was reset anyhow), SWD line reset sequence (part of
JTAG-to-SWD already) and the mandatory IDCODE read. Schedule that to
be performed on the next poll.
Fix the return values for ftdi and jlink drivers to be consistent with
OpenOCD error codes and remove ad-hoc calls to perform DAP method
switching (as it's now done from the upper layer automatically).
Change-Id: Ie18797d4ce7ac43d8249f8f81f1064a2424e02be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2371
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mateusz Manowiecki <segmentation@fault.pl>
When a target was present on OpenOCD start but later disappeared for
whatever reason (typically unstable connection or target going to
sleep) and reappeared only for a brief period of time, reexamination
would fail, and poll would no longer run. This patch fixes it.
Change-Id: I61f9b5a3f366a761320e233f4e1689f926b5556d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2370
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The FSF address has changed; The FSF site says that
address is
Free Software Foundation
51 Franklin Street, Fifth Floor
Boston, MA 02110-1301
USA
(see http://www.fsf.org/about/contact/)
Instead of updating it each time the address changes,
just drop it completely treewide.
Change-Id: I27199f7625901f677d8105d1e8876cff00147b71
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2340
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
added "Single Wire Output" and "Trace Memory Controller" peripheral
IDs to dap_rom_display(), which is invoked by the "dap info" command
Change-Id: Iea3201007bb98e6376fbb50be40a4a2e031b0a03
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When looking for a debug base address of a core, one should search
through all the ROM tables, not just the top-level one.
This code also assumes that the first found entry (in a depth-first
search) will correspond to core 0, the second to core 1 etc.
The patch is supposed to be an alternative implementation of
http://openocd.zylin.com/#/c/1313/.
Change-Id: Ifc88971a02fe3d9c00d9bf72a822ade5804d4e09
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code treats registers that are shadowed in FIQ mode in a special
way: to read them out the target is first switches to USR mode. But
since USR != ANY the current implementation later skips register read,
and the loop becomes endless in case any !valid ARM_MODE_ANY is
present at the moment arm_dpm_full_context() is called. This was
reported in https://sourceforge.net/p/openocd/tickets/76/. The issue
surfaced because 2efb1f14f6 added two
ARM_MODE_ANY registers ("sp" and "lr") which were not normally read,
so at the time a user was calling "arm reg" they were not valid.
Fix this by changing the mode appropriately while keeping the "mode"
variable state intact so it would later match register's mode.
Compile-tested only.
Change-Id: I01840e8fa20ec392220138a3f1497ac25deb080a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
This was very helpful when debugging programs during async loading.
Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Using custom build-time tools is always more problematic, especially
for cross-compiling.
This alternative implementation assumes "od" (IEEE Std 1003.1-2001)
and sed are available which should be the case for any reasonably
modern system.
Change-Id: I0208f475648c78e7dca127ff4bab60d314b2bf53
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2139
Tested-by: jenkins
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If load_image address overlap with fast_data_area,
it will caouse different mysterius issues. This patch
should prevent it.
Change-Id: Ibc95e5aa3ac002a59755029496b6a72616e9287f
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1854
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A previous commit changes the target name used by tcl scripts.
commit d9ba56c295
target: rename cortex_a8 to cortex_a
The current change renames target functions and definitions in the
implementation from cortex_a8 to cortex_a.
This prepares the implementation to support Cortex-A8, A9, A15-MPCore
in one place.
Change-Id: I73b5a38a92c12ba5bd3b806fbbb664817575a6d7
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1599
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Polling was disabled based on global variables jtag_trst and jtag_srst
which were never touched in non-JTAG mode. Modify the check and remove
the ugly workaround to avoid calls to a possibly uninitialized JTAG
subsystem.
Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2143
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also align them with spaces instead of tabs.
Change-Id: I1c01412a3ea77b29e8e133f5c92d05ed79d7c0f3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2133
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only
setting that is guaranteed to be implemented, as well as being the reset
value in ADIv5.0.
Thus it makes no sense supporting anything else.
Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2132
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Robert P. J. Day
Uwe Bonnes
Christopher Head
Andreas Fritiofson
Antony Pavlov
Daniel Glöckner
Olivier Schonken
Paul Fertser
Jose de Sousa
Uwe Kleine-König
Alexander Stein
Kamal Dasu
Salvador Arroyo
Jens Bauer
Peter Lawrence
Spencer Oliver
Jon Burgess
Angus Gratton
Oleksij Rempel
Mathias K