Move setting of do_reconnect flag from swd_run_inner()
to swd_run(). Reconnect is not used at the inner level
and the flag had to be cleared after swd_run_inner()
to prevent recursion.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib1de80bbdf10d1cbfb1dd351c6a5658e50d12af2
Reviewed-on: https://review.openocd.org/c/openocd/+/8155
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
ADIv6 brought more complicated rules for DP reg 0 banking.
Neither the original implementation [1] nor the later
modification [2] respected that the DP reg 0 is banked
for read only, not for write. Enforcing of an useless
SELECT write before a write to ABORT register may trigger
FAULT (CTRL/STAT bits ORUNDETECT and STICKYORUN are set)
or WAIT (DP is stalled by an outstanding previous operation)
and therefore make ABORT register virtually unusable
on some adapters (bitbang, CMSIS-DAP).
There are DP ABORT specific functions swd_queue_ap_abort()
and swd_clear_sticky_errors() which worked around the problem
using the lowest level swd->write_reg(). Using a specific
write procedure for a single DP register was error prone
(there are other DP_ABORT writes using swd_queue_dp_write_inner())
and also the Tcl command 'xx.dap dpreg 0 value' suffered
from unwanted SELECT write.
Other smaller discords in DP banking probably do not
influence normal DP operation however they may complicate
debugging in corner cases.
Adhere strictly to the DP banking rules for both ADI versions.
Fixes: [1] commit 72fb88613f ("adiv6: add low level swd transport")
Fixes: [2] commit ee3fb5a0ea ("target/arm_adi_v5: fix DP SELECT logic")
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I3328748c1c3e0661c5ecd6eb070ac519b190ace2
Reviewed-on: https://review.openocd.org/c/openocd/+/8154
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some devices with an internal multi-tap JTAG router require a vendor
specific bypass instruction to bypass the master TAP when addressing
slave taps internal to the same device. On these devices the standard
bypass instruction bypasses the whole device.
Change-Id: I4506f0e67c9e4dfe39b7fa18c63d67900313e594
Signed-off-by: Henrik Nordström <henrik.nordstrom@addiva.se>
Reviewed-on: https://review.openocd.org/c/openocd/+/8041
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
swd_connect_multidrop() sent DORMANT_TO_SWD and called
swd_multidrop_select_inner(). DORMANT_TO_SWD sequence ends
with a LINE_RESET sequence.
swd_multidrop_select_inner() sent LINE_RESET sequence again.
It was useless in this case.
swd_connect_multidrop() emited JTAG_TO_DORMANT and DORMANT_TO_SWD
sequences before connecting each DAP in SWD multidrop bus.
It is sufficient to emit JTAG_TO_DORMANT and DORMANT_TO_SWD
just once and emit the shorter LINE_RESET instead for subsequent DAPs.
Introduce a global variable swd_multidrop_in_swd_state
and use it to control what sequence is emitted.
In case of reconnect after an error, always use the full switch
JTAG_TO_DORMANT and DORMANT_TO_SWD.
Change-Id: Iba21620f6a9680793208bf398960ed0eb59df3b1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7218
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The original code supported ADIv5 only, just one SELECT register
with some reserved bits - the pseudo value DP_SELECT_INVALID was
just fine to indicate the DP SELECT register is in an unknown state.
Added ADIv6 support required DP SELECT and SELECT1 registers
without reserved bits. Therefore DP_SELECT_INVALID value became
reachable as a (fortunately not really used) ADIv6 AP ADDR.
JTAG DPBANKSEL setting support introduced with ADIv6 does not
honor DP_SELECT_INVALID correctly: required select value
gets compared to DP_SELECT_INVALID value and the most common zero
bank does not trigger DP SELECT write.
DP banked registers need just to set DP SELECT. ADIv6 AP register
addressing scheme may use both DP SELECT and SELECT1. This further
complicates using a single invalid value.
Moreover the difference how the SWD line reset influences
DPBANKSEL field between ADIv5 and ADIv6 deserves better handling
than setting select cache to zero and then to DP_SELECT_INVALID
in a very specific code positions.
Introduce bool flags indicating the validity of each SELECT
register and one SWD specific for DPBANKSEL field.
Use the latter to prevent selecting DP BANK before taking
the connection out of reset by reading DPIDR.
Treat DP SELECT and SELECT1 individually in ADIv6 64-bit mode.
Update comments to reflect the difference between ADIv5 and ADIv6
in SWD line reset.
Change-Id: Ibbb0b06cb592be072571218b666566a13d8dff0e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7541
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
and DP_SELECT_DPBANK.
Use the defined symbols instead of magic numbers.
Change-Id: I19c86b183e57e42b96f76eed180c0492cd67bee1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7539
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DP_SELECT_APSEL and DP_SELECT_APBANK is no more used in ADIv6.
Change-Id: I4176574d46c6dc8eb3fe3aef6daab6e33492c050
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7538
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While there:
- fix memory leak in case of error on values tap->chip,
tap->tapname, tap->expected_ids;
- check for out of memory error;
- fix minor coding style issue;
- add the missing .usage field;
- remove functions not in use anymore.
Change-Id: I1c8c3ffeb324e9eacb919c7e0d94fd72122c9a81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7431
Tested-by: jenkins
The multidrop SWD is also supported.
Change-Id: I9fefc54fc9d40a75194285cd6e0f10c5c347d9b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7537
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
swd_multidrop_select() uses its own retry loop.
If select fails, do_reconnect flag remains set on exit and causes
useless reconnect.
Clear do_reconnect flag in retry loop.
Change-Id: Ie06d6967d7f4a977774c8530bb8d4b3e5ab4f62c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7217
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Implementation of ADI v6 introduced banking of DP reg 0.
The accompanying change preventing DP SELECT write before
DP IDR read during connect was added to swd_connect_single() only.
Unchanged swd_connect_multidrop() / swd_multidrop_select_inner()
was broken as it emited DP SELECT and put DP to protocol error state.
Copy dap->select handling to swd_multidrop_select_inner().
Fixes: 72fb88613f (adiv6: add low level swd transport)
Change-Id: I514cd6d9ae2ba97ce3657b459df22638c278a0b1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
During enter in SWD read DP_DPIDR without selecting the register
bank through DP_SELECT_DPBANK.
Handle the different format of DP_SELECT register.
Change-Id: Iea1b8eb6ec94177e16a430d5885595a38e833eeb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6697
Tested-by: jenkins
swd and dap-direct are not implemented yet
Split from change https://review.openocd.org/6077/
Change-Id: I6d73d8adf6a6090001c5d4771325fb1d63c45e3c
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6459
Tested-by: jenkins
ARM IHI 0031A does not support SWJ-DP, so no switch between JTAG
and SWD is considered.
ARM IHI 0031B is not publicly available and it's reported as
"Confidential Beta" in the history list in following doc versions.
From ARM IHI 0031C the direct switch between JTAG and SWD is
already deprecated in favor of passing through dormant mode. With
no access to IHI 0031B we haven't info if any device strictly
requires the direct switch.
OpenOCD implements only the deprecated direct switch, so changing
it could cause regression on devices that do not implement dormant
mode.
Plus, not all the adapters support dormant mode.
Nevertheless there are already target devices that only allow
entering in SWD by passing through dormant.
Let the code try both method, alternating one tentative with the
deprecated legacy direct switch, then another tentative passing
through dormant, and repeat till timeout.
This would work on any device that don't support dormant, on new
devices that require switch through dormant and will work with
adapters that don't support dormant.
Change-Id: Ib8619635277d497872079a33fa4e38be9beb84a0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6695
Tested-by: jenkins
Based on Graham Sanderson's http://review.openocd.org/4935
Unlike Graham Sanderson's version this patch does not add
any multidrop specific queuing.
Multidrop SWD is handled mostly by the same code as single SWD,
just a selection sequence is prepended to a SWD operation
as needed.
This is a minimal working implementation without checking for
configuration errors (mixing multidrop and non multidrop DPs,
multiple use of the same selection id etc...).
Multidrop switching likely demands changes in the adapter code.
Change-Id: I99a5742c209b49c0483e800f6105cb5e59a897d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6141
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is a preparatory change for swd multidrop, mostly refactoring.
Split swd_queue_dp_read/write() to inner and outer parts.
Use the inner parts in swd_queue_dp_bankselect(), swd_connect()
they do not need to check reconnect.
Use the outer parts exclusively in swd_dap_ops.
Rearrange the code to reduce forward declarations.
Change-Id: I47b7f0cb037e0032a267463f06ba02123ba96fe7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6139
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
Reading of DPIDR is the very first operation after JTAG to SWD sequence.
Without this change if DPIDR read fails then swd connect fails.
Keep trying JTAG to SWD sequence and DPIDR read until success
or timeout 0.5 sec. It makes setting of adapter srst delay on SWD transport
mostly unnecessary.
Also test for ERROR_WAIT (which should not occur according to
IHI 0031E B4.3.2 but a quirk is known) and if bus is kept stalled
then issue abort to make the next connect possible.
Change-Id: Id8fe6618605bbeb4fed5061e987ed55de90a35f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
To reorganize the adapters code, introduce an adapter_driver
struct that contains all the adapter generic part, while
keeping in two separate struct the specific API jtag_ops and
swd_ops.
Move the allocation of *adapter_driver from the JTAG-specific
file core.c to the more adapter-specific file adapter.c
While splitting the old jtag_interface for every driver, put
the fields in the same order as in the struct declaration so
we keep a consistent code across all the drivers.
While other transport specific API could/would be added as
separate ops, nothing is done here for HLA.
Change-Id: I2d60f97ac514c0dd2d93a6ec9be66fd9d388dad5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4900
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The transport SWD uses the JTAG queue to assert/deassert the
system reset srst. This is the major inconsistency that has to be
removed to properly split JTAG and SWD.
Introduce a new driver API, reset(), to controls both the signals
trst and srst in the driver, skipping the JTAG queue. Put the new
API in struct jtag_interface, even if in this patch it's used for
SWD only; the goal is to get it reused by the other transports.
Add the implementation of the API in all the drivers that
implement SWD. Such implementation is almost the same of the old
code in JTAG queue.
Create a wrapper adapter_system_reset() to use the new API and
remove the SWD specific swd_add_reset(). In the wrapper replace
jtag_add_sleep() with jtag_sleep(), because the former uses the
JTAG queue too.
Rename the old jtag_add_reset() as legacy_jtag_add_reset() with
the target to remove it when all drivers would be ported to the
new reset API. Create a new jtag_add_reset() that calls the
legacy function for drivers still on the old reset API.
Use the new API also on JTAG transport for the drivers that can
support both SWD and JTAG.
For the moment, do not modify the implementation of JTAG-only
drivers, which will continue using the usual method. This should
be cleaned-up in future commits.
Change-Id: I32331c88313f6059b25e12c6bb0156aebc1c074f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().
Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h
Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command 'swd' does not have the '.usage' field filled out
Change-Id: I5a36c0fc822c4d5d74ef2d1c75e369648c6f7d4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4830
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Write to register DP_SELECT can fail, but both functions
swd_queue_dp_bankselect() and swd_queue_ap_bankselect() return
void and do not propagate the error.
Change the return type of the two functions to int and check the
returned value.
Invalidate the cached value of DP_SELECT if the write fails.
Change-Id: Iba6ef8b0c2332e7f7efb66337d558fb7a4a0d39c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4980
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the register DP_SELECT is written directly, e.g. with command
<dap> dpreg 8 <value>
the cached value in OpenOCD is not completely updated with the new
value, thus creating issues in the following AP and DP read/write
that rely on the cached value.
Update the cached value while writing to DP_SELECT.
Change-Id: I8221b10cd6fc1fbe73e6b834b68820b43480e1a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4979
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The functions dap_to_jtag() and dap_to_swd() have been introduced by
3ef9beb52c ("ADIv5 DAP ops switching to JTAG or SWD modes") in
arm_adi_v5.c by using the JTAG queue only.
Later, in 6f8b8593d6 ("ADIv5 transport support moves to separate
files") the functions has been moved in adi_v5_swd.c and adi_v5_jtag.c
but keeping the dependency from JTAG queue.
The functions does not work if the current transport is not JTAG.
Move back the functions in arm_adi_v5.c, replace the input parameter
"target" with "dap", use the transport to detect if the JTAG queue is
present, in case of SWD transport use the proper method, for other
transports report error.
Reuse the ADI v5 sequences already present in jtag/swd.h.
Also, OpenOCD does not support switching to another transport after
the initial selection, so do not change DAP's ops vector.
Change-Id: Ib681fbaa60cb342f732bc831eb92de25afa4e4db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4852
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Problem: If the same memory location is accessed alternatively
by MEM-AP banked data registers without autoincrement and by standard
autoincremented read/write, TAR register is not updated correctly.
How to replicate: On a Cortex-M issue
mdw 0xe000edf0
multiple times. When poll is on (poll reads the same memory location)
only the first read is correct.
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 20002640
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 00000000
No problems with poll off.
0xe000edf0: 01000000
0xe000edf0: 01000000
0xe000edf0: 01000000
mem_ap_setup_tar() writes to MEM_AP_REG_TAR if requested TAR value
changed or CSW_ADDRINC_... is currently active.
However if an autoincremented access has been issued and autoinc
switched off in CSW afterwards, TAR does not get updated.
The change introduces mem_ap_update_tar_cache() which is called
after queuing of any access to MEM_AP_REG_DRW. It simulates
TAR increment to keep tar_value in sync with MEM_AP.
Crossing tar autoincrement block boundary invalidates cached value.
mem_ap_write() and mem_ap_read() do not check tar autoincrement
block boundary, mem_ap_setup_tar() is called before each transfer instead.
dap_invalidate_cache() is introduced to ensure invalidation
of all cached values during dap_dp_init() and swd_connect()
Change-Id: I815c2283d2989cffd6ea9a4100ce2f29dc3fb7b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4162
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Today the reset option for connect_assert_srst is not done for SWD.
This patch adds this to SWD and make it possible to connect to targets which might disable JTAG interface when running.
Change-Id: Ib89f7cf59b628e8f0b5fca9dd9e362e383c4b99f
Signed-off-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-on: http://openocd.zylin.com/3018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Note:
WCR (Wire Control Register) is replaced by DLCR (Data Link Control
Register). And only TURNROUND field is modifiable.
[andreas.fritiofson@gmail.com]:
Rename DP_IDCODE to DP_DPIDR as well.
Sort list by address and align it using spaces instead of tabs. Add
comments about supporting DP versions.
Remove non-functional wcr command completely.
Change-Id: Ic6b781b07c8eead8b0237d497846d0da060cb1ba
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3244
Tested-by: jenkins
The cache is forced to zero to match the value expected by the DPIDR read
so the connect sequence is not destroyed by a SELECT update.
However, DPIDR and in fact all registers except address 4 are independent
of the current DPBANKSEL value. Change swd_queue_dp_bankselect() to use
this fact and avoid touching SELECT for those registers.
Change-Id: I0cd11925fb6adef481bbf45cc24ea2c6dab4b6fb
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3231
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 830d0c55c0 introduced
a regression in error recovery after reconnect:
If first SWD queue run in dap_dp_init() fails, DP_SELECT
does not get reset.
Change-Id: I947e2afe9933e4645a6141ece7816af8e6082cf2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3194
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
BeagleBone debian 7 builds produce:
adi_v5_jtag.c: In function 'jtag_ap_q_bankselect':
adi_v5_jtag.c:336:11: error: declaration of 'select' shadows a global declaration [-Werror=shadow]
Fix this by changing the local variable to 'sel'.
Change-Id: I8e29662ac12bc77d38d5064046d59b7364853cd9
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3184
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove entirely the concept of a "selected" AP that has to be maintained
between calls. All the information the DAP ops need are now provided to
each call through the AP/DAP pointer.
Consolidate the cache of the SELECT fields into one single field caching
the entire register.
Change-Id: I2e1c93ac5ee8ac38a7d680ca2c660c30093a6b87
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3165
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function does two separate things, powering up the DP and setting
up a MEM-AP. But the DP needs to be powered before even searching for a
MEM-AP to initialize and targets may have multiple MEM-APs that need
initializing.
Split the function into dap_dp_init() and mem_ap_init() and change all
call sites to use the appropriate one.
Change-Id: I92f55e09754a93f3f01dd8e5aa1ffdf60c856126
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3151
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Not clear what it was supposed to be used for. It probably shouldn't.
Change-Id: Ife1d833e59ba80f93876447d752a0ca7e7b57b0f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3143
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Making the SWD driver aware of the DAP that controls it is a layering
violation.
The only usage for the DAP pointer is to store the number of idle cycles
the AP may need to avoid WAITs. Replace the DAP pointer with a cycle
count hint instead to avoid future misuse.
Change-Id: I3e64e11a43ba2396bd646a4cf8f9bc331805d802
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3141
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This brings SWD reconnection procedure in line with the ARM
documentation and changes cortex_m reset procedure to make use of it.
The motivation behind this patch is to make SAM4L "reset" and "reset
halt" properly without SRST. The complication here is that EDBG issues
an additional read of DP_RDBUFF automatically right after writing
SYSRESETREQ, that leads to a FAULT which needs to be dealt with
properly. With this patch the very first ahbap_debugport_init DAP
access will make SWD layer properly reinitialise the link before
continuing.
Runtime tested with mbed CMIS-DAP + KL25 only.
Change-Id: Ic506f9db30931dfa60860036b83f73b897975909
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2596
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When communication with target fails for whatever reason, it makes
sense to do JTAG-to-SWD (in case the target got power-cycled or the
DAP method was reset anyhow), SWD line reset sequence (part of
JTAG-to-SWD already) and the mandatory IDCODE read. Schedule that to
be performed on the next poll.
Fix the return values for ftdi and jlink drivers to be consistent with
OpenOCD error codes and remove ad-hoc calls to perform DAP method
switching (as it's now done from the upper layer automatically).
Change-Id: Ie18797d4ce7ac43d8249f8f81f1064a2424e02be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2371
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mateusz Manowiecki <segmentation@fault.pl>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
Polling was disabled based on global variables jtag_trst and jtag_srst
which were never touched in non-JTAG mode. Modify the check and remove
the ugly workaround to avoid calls to a possibly uninitialized JTAG
subsystem.
Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2143
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only
setting that is guaranteed to be implemented, as well as being the reset
value in ADIv5.0.
Thus it makes no sense supporting anything else.
Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2132
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek
Henrik Nordström
Antonio Borneo
Kevin Burke
Matthias Welwarsky
Jonas Norling
Fredrik Hederstierna
Marc Schink
Andreas Fritiofson
Peter A. Bigot
Paul Fertser