Found by grepping for pointer casts.
Also rewrite to reduce scope and allocate the few bytes needed on stack
instead of on heap.
Change-Id: Ia2a369fb612e807b981ee60ebcfd9c09c2fbdf4c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1779
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When pointer casts are needed, cast directly to the correct type, instead
of going via void*.
Don't explicitly cast to void* if it would have been done implicitly.
Change-Id: I4093209200051c5eb62847d00a4b9c8567480068
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1669
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Don't use const on pointers that hold heap allocated data, because that
means functions that free them must cast away the const.
Do use const on pointer parameters or fields that needn't be modified.
Remove pointer casts that are no longer needed after fixing the constness.
Change-Id: I5d206f5019982fd1950bc6d6d07b6062dc24e886
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1668
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This eliminates most of the warnings reported when building for
arm-none-eabi (newlib).
Hsiangkai, there're many similar warnings left in your nds32 files, I
didn't have the nerve to clean them all, probably you could pick it
up.
Change-Id: Id3bbe2ed2e3f1396290e55bea4c45068165a4810
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the fpb_enabled is not set then as part of cortex_m3_set_breakpoint we
enable the fpb, however we do not signal the fpb as being enabled.
This issue only effects the hla target as the current cortex_m code enables
the fpb during cortex_m3_endreset_event.
Change-Id: I44d3fc65916c131b7a226869dd16aed5afb441b4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1634
Tested-by: jenkins
Polling target does not change stste information
except if new state is TARGET_HALTED.
Connecting to the runing target result in target->state
not updated with retrieved value and remains "UNKNOWN"
until 'halt' command issued.
Change-Id: I803d6c0207f7f8699e648779d1df342c9ee7315a
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1680
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a mandatory field in struct arm7_9_common for regular, non-optimized
memory writes. Together with the existing bulk_memory_write field, this
allows variants to select any combination of implementations for regular
and bulk writes, without risking infinite loops from accidentally using
bulk writes for implementing bulk writes.
ARM 7/9 targets may now select arm7_9_memory_write_opt as their
target.write_memory implementation, which will dispatch to
arm7_9_common.bulk_write_memory if possible, or fallback to
arm7_9_common.write_memory otherwise.
To avoid loops, bulk write implementations mustn't call any other
functions than arm7_9_write_memory_no_opt() to write memory; it will
unconditionally call arm7_9_common.write_memory. If they fail, they should
simply return error to allow the caller to fallback to regular writes.
Tested on a regular ARM7TDMI only.
Change-Id: Iae42a6e093e2df68c4823c927d757ae8f42ef388
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1685
Tested-by: jenkins
Reviewed-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We changed the actual target name quite a while ago.
This changes the actual target function names/defines to also match
this change.
Change-Id: I4f22fb107636db2279865b45350c9c776e608a75
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1626
Tested-by: jenkins
Create a single pair of relatively simple functions to handle all variants
of MEM-AP transfers. This replaces the many separate functions that
handled different access sizes and packed or non-packed transfers, which
were all implemented rather differently.
With this single implementation, performance should be more consistent,
regardless of transfer type.
Change-Id: I89960e437fc6ba68a389c074fab8eac91abcf844
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Accessing one byte of memory using a 16-bit access is not well defined.
The current implementation is forgiving and rounds up, but it should not
be relied upon.
Also, I suspect this code might fail if the byte order differs between
target and host, but I have no way of verifying it so I left it as it is.
Change-Id: I8d6a511151a194ed419f141703201f0632d84fc8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1657
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The word count returned from max_tar_block_size() was compared with the
count of half-word/bytes in the u16 and u8 packed access functions,
causing an infinite loop if the access actually crossed the boundary.
Change max_tar_block_size() to return a byte count, and scale at the call
site.
Change-Id: I2fe9b5941eb485f3d8219cfdd29fb71e02006de4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1649
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For packed and/or unaligned accesses, the write functions reordered the
source buffer in place. Causing in the best case a segfault, in the worst
case silent data corruption.
Rewrite the data fetching to directly match the byte lane mapping
according to IHI0031C, without destroying the buffer.
Also slightly clean up variable usage and harmonize all the write
functions.
Change-Id: I9a01cfc5578653f9ec02043ff6b61a7a20f90d67
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1646
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's been like this since the check was added, in 5aa93a5e.
Change-Id: Iaa0586e0cd1ce57ad92735dcc3e51108a133fe96
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1640
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to issues reported when using the jtag mode of the stlink (see Trac #61),
the functionality/checking has been moved to the driver.
This change also fixes unaligned 32bit memory read/write for the stlink.
From testing this change also brings a 3KiB/s speed increase, this is due
to the larger read/write packets.
Change-Id: I8234110e7e49a683f4dadd54c442ecdc3c47b320
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1632
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is the first part in moving the adapter specific api back into the
driver.
The next task is to also move the hla read/write buffer size handling.
Change-Id: I86a19144b50b6de18659bfcd05b3729b2cafc051
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1621
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Now that we support the target description format we do not need
these hacks anymore, we can now tell gdb what registers we support.
Change-Id: Ie774231d296420b35efcf708bc4435475c87ff5e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1617
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for the default gdb register description type "int" and "float".
When this is given to gdb it will use the bitsize to determine the reg size.
Change-Id: Iaeed594d1feece54044128eae1baff9858bdcae0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1622
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Half-word and byte writes using mwh/mwb has been completely broken since
bf71e34cbf, because it dispatched all writes, regardless of access size,
to target_write_buffer(), which uses as large accesses as possible.
Partially revert the commit by changing back to the correct write method.
Change-Id: I60731fc576bf4a076a7da02bee7879e121c21d17
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1628
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently we try and use MEM-AP packed transfers as much as possible for
8/16bit transfers. However not all targets support packed transfers, so
check before using.
Change-Id: I66256007f25ccd0c583f23db5acf6d1aa8b5e57d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1602
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
.soft_reset_halt is not necessary for nds32 target.
Remove the dependency.
Change-Id: Ic3b126d6c7eb995583a661b762627e736222fcaa
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1612
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As GDB uses file-I/O protocol to access memory, use DMA to access
if no DCache. This commit improves the performance of Andes
Virtual Hosting.
Change-Id: I36bb2154b9f497fc4237625836cf8c7115330a60
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1580
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Modify handle_nds32_memory_access_command: do not use DCache
setting to block user's setting.
Change-Id: I2d33f893773e2a2e3e2f26edde5938ef5902609d
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1579
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If multiple read watchpoints are hit at the same time, report
any one of these hit watchpoints.
Change-Id: I8d4439aa80e4b62bb7d48bbdc0450920e2008a2e
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1576
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do not turn on/off polling as leave/enter debug mode.
Enable polling after gdb attached, and disable polling
after gdb detached.
Change-Id: Id64459b86f44937af7ea5ccfe2cd13e31732eecf
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1574
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
1. gprof uses 2-bytes as minimum bucket size.
2. As user wants to use gprof --sum to summarize multiple
profiling data files, the range MUST be the same.
Add new arguments to specify profiling range.
Change-Id: Ie7e6afa6a4d82250e2d194a0eed2b428c1479ea1
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1572
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Profiling could be target-specific. Add .profiling interface
to target_type.
Change-Id: Ic0eea9db742971db1350a474fbbb5ed24565922b
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1571
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
I do not know what is the reasonable number of buckets.
If there are enough buckets, the result will be accurate.
I propose increase the maximum number of buckets to 128K.
If the size of program text section is less than 256KB, every
two bytes will be occupied by one buckets.
(The minimum size of one buckets is 2 bytes in gprof implementation.)
Change-Id: If9147743cefdc36f40f21e6dc73b9b28f28c9e1e
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1608
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
1. high_pc should be (maximum sample + 1) (Refer to gprof source code)
2. bucket index should be
sample offset
--------------- x (number of bucket)
sample range
For example, if minimum sample is 0 and maximum sample is 5
and the number of bucket is 3.
a = sampled_address - 0
b = 3
c = 6
(a, b, c refer to source code variables)
sampled_address = 0, => a = 0, => bucket_index = 0
sampled_address = 1, => a = 1, => bucket_index = 0
sampled_address = 2, => a = 2, => bucket_index = 1
sampled_address = 3, => a = 3, => bucket_index = 1
sampled_address = 4, => a = 4, => bucket_index = 2
sampled_address = 5, => a = 5, => bucket_index = 2
Change-Id: Ia9fa0e4d9c7183e3e9d7ceaf73e63729f07aa2ce
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1607
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change variable name 'length' to 'numBuckets'. It is more readable.
Change-Id: I913cba0746f887adf6da401a46cd5e9ea88d2c6d
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1606
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rewrite the target_*_buffer_default to generate as large accesses as
possible while maintaining natural alignment.
These versions are easy to extend to generate 8-byte accesses to support
64-bit targets, although it requires some conformity from all target
implementations (i.e. they need to refuse unsupported access sizes with
some defined error code, so we can try again with a smaller one).
Change-Id: I00ddcbb1d2fd33f9f8b99cb448cc93505a2421fc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1221
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only remaining user is arm7_9 so remove it from the target API and add
it to struct arm7_9_common to support all its variants with minimal
changes. Many of the variants are likely not correct in the cache/mmu
handling when the bulk write is triggered. This patch does nothing to
change that, except for arm946e, where it was easier to do what might be
the right thing.
Change-Id: Ie73ac07507ff0936fefdb90760046cc8810ed182
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1220
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We already set cpsr in armv7m_build_reg_cache, so lets use it for all other
accesses to this field.
Change-Id: I19b3b21ecf1571bbea12e1be664845e6544f6fa1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1539
Tested-by: jenkins
Make sure the target support target requests before we enable any receivers.
Change-Id: I8ce42922eaff76fb5e7a114da716f2a6585a6ab5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1536
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Let the default handler issue an unsupported warning rather than using
empty handler routines that may/may not issue a unsupported warning.
Change-Id: Iafe3e45146981a4cfae39771c3ab7370ac86da48
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1535
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
If target does not support semi-hosting function, it has
no need to provide .get_gdb_fileio_info callback. OpenOCD
will use default function target_get_gdb_fileio_info_default.
The default function just return ERROR_FAIL and gdb_server
will treat every halted condition as normal halted and
return "Txx" to gdb.
Change-Id: I9ddb2be3a1145eae2ef5b712bdea89eb2e0fbc20
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1586
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After the target was reset we can be sure it's not running any
algorithm.
This fixes the following failure scenario:
On my STM32F103 board after I start the firmware and then stop and try
to "load" in gdb (before doing mon reset halt), I get
Error: timeout waiting for algorithm, a target reset is recommended
However, target reset doesn't help as the flag is still there ("Error:
Target is already running an algorithm"), so I have no choice but to
restart the OpenOCD process.
I'm not sure yet what exactly prevents load from working after my
firmware is initialised, most probably some interrupt is firing and my
handler produces a fault due to garbled RAM.
Change-Id: Idd977f2780a64d84800e3abd412cffc1ab6801b0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1512
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Enable reading the SWO trace output via STLinkv2 dongles that support
it.
This adds an optional initialization parameter "trace" with which the user
specifies a destination file where SWO trace output is appended as it comes in
as well as the trace module's source clock rate.
STLink will be configured for a 2MHz SWO data rate (STLink's highest
supported rate) if the source clock is > 2MHz, otherwise the source
clock is used as the data rate directly.
For example:
trace swo.log 168000000
If "trace" is specified with a usable file path, the stlink_usb driver will
attempt to configure and read SWO trace data as follows:
- on _run(), the target's TPI and TMI are configured and the STLinkv2 is told
to enable tracing. Only generic ARM TPI and TMI registers are
configured, any MCU-specific settings (ex: pin routing) are the
responsibility of the target firmware. The configuration applied is
based on the STLinkv2's capabilities (UART emulation).
- on _v2_get_status(), the trace data (if any) is fetched from the
STLink after the target status is checked and the target is found to
be running.
- on _halt(), the STLink is told to disable tracing.
When fetching trace data, the entire trace frame is written to the output file
and that data is flushed. An external tool may be used to parse the
trace data into a more human-readable format.
Tested on ARM Cortex M4F and M3 MCUs (STM32F407 and STM32L152).
Change-Id: Ic3983d46c82ba77010c23b0e18ce7b275d917f12
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1524
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently, there is no way to notify gdb that program has exited.
Add new target_debug_reason called DBG_REASON_EXIT to notify gdb
the condition has occured. If the debug reason is DBG_REASON_EXIT,
gdb_server will send 'W' packet to tell gdb the process has exited.
Change-Id: I7a371da292716a3e6ac4cc2c31b009a651fe047a
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1242
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The File I/O remote protocol extension allows the target to use the
host's file system and console I/O to perform various system calls.
To use the function, targets need to prepare two callback functions:
* get_gdb_finish_info: to get file I/O parameters from target
* gdb_fileio_end: pass file I/O response to target
As target is halted, gdb_server will try to get file-I/O information
from target through target_get_gdb_fileio_info(). If the callback function
returns ERROR_OK, gdb_server will initiate a file-I/O request to gdb.
After gdb finishes system call, gdb will pass response of the system call
to target through target_gdb_fileio_end() and continue to run(continue or step).
To implement the function, I add a new data structure in struct target,
called struct gdb_fileio_info, to record file I/O name and parameters.
Details refer to GDB manual "File-I/O Remote Protocol Extension"
Change-Id: I7f4d45e7c9e967b6d898dc79ba01d86bc46315d3
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1102
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In GDB remote serial protocol, the stop reply packet could contain more
detail stop reason. The currently defined stop reasons are listed below.
* watch
* rwatch
* awatch
* library
* replaylog
This commit adds stop reason, watch/rwatch/awatch, in stop reply packet for
just hit watchpoint. As manual indicates, at most one stop reason should be present.
The function needs target to implement new hook, hit_watchpoint. The hook will fill
the hit watchpoint in second parameter. The information will assist gdb to locate
the watchpoint. If no such information, gdb needs to scan all watchpoints by itself.
Refer to GDB Manual, D.3 Stop Reply Packets
Change-Id: I1f70a1a9cc772e88e641b6171f1a009629a43bd1
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1092
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Documentation says they should be given values in milliseconds,
DEFAULT_HALT_TIMEOUT matches that too.
Change-Id: Ic1a30fa90f75b412c43fe50ba187d01c3d0a5fba
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1504
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When I do not have the JTAG adapter connected to the target, I often
end up always reading 1s from the chain. If the OpenOCD is configured
to connect to an ETM-equipped target (i.MX25 ARM9 in my case), this
results in writing garbage values in the etm reg_cache as the ETM bit
fields for the comparators, counters and outputs are wider than the
amount of entries in the corresponding arrays. This later results in a
segfault in the first etm_reg_lookup() call.
Change-Id: Ied81fdbf3a53a3dd749e2e5e97adf86c012df575
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1505
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
EJTAG 1.5, 2.0 and 2.5 have different breakpoint register addresses.
This patch add support of EJTAG 2.0, which is part some broadcom
SoCs.
This work was testet on Broadcom BCM7401.
Change-Id: I4b0ee23871fa9205f9001b7c9165e7b6ebe9ccbf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1464
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Split function mips32_configure_break_unit
to mips32_configure_ibs and mips32_configure_dbs
to make code more readable.
This will probably make work easyer with differnet EJTAG versions.
Change-Id: I666f949fd7bc3656bdf75e7bcaadb164f15855dd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On some CPUs, like bcm7401 with EJTAG v2.0 we can have situation where
CPU do not stops execution. For example, all CP0 commands will have this issue.
In this case we should some hove recover our session. Currently
jump to 0xff20.0200 seems to be good option. If it brake some thing on
newer EJTAG, then check for EJTAG v2.0 should be added.
Change-Id: Icd8841f38a1a85e0f7682b6dc358af8dfaae0744
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Reviewed-on: http://openocd.zylin.com/1353
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This instruction we will need to make jump to 0xff20.0000
Change-Id: Ic723e683e8848492cd8e186e71fd668dbd1d97e6
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Reviewed-on: http://openocd.zylin.com/1338
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some parts of code are version specific. It will be easier
if we extract ejtag version and store it some where.
Change-Id: I8f9addc42108cba5ae9d61b8ade8f9d7f02a0fb5
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1462
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On slow targets we sometimes get false messages about timeouts due to poll
using 1sec rather than the default 5sec timeout.
Change-Id: Icc81c78e0ca86cebf9eeb2f5307cf7a82f1f4ee8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1466
Tested-by: jenkins
Added missing breakpoint/watchpoint implementation to dsp563xx target.
Implementation is not yet complete, which means it does not leverage all
available features of the once debug interface.
This does NOT use the openocd breakpoint/watchpoint command because of
the "special" memory address spaces (X/Y/P/L) of the 56k DSP series.
Change-Id: I6840a3ff1e6fdebb38ab7758f164886aff773af6
Signed-off-by: Bernhard Kiesbauer <bernhard@kiesbauer.com>
Reviewed-on: http://openocd.zylin.com/1468
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
gcc (Gentoo Hardened 4.6.3 p1.13) produces a warning about the variable
assigned but not used. write() can sometimes write less than the specified
count so it's marked with warn_unused_result in the system headers and its
return value can't be ignored. The most correct solution would be to have a
loop writing the buffer until all bytes are written or an error is
returned but here it's impractical.
Change-Id: I75f7482e2b26fe0e6d70d34947518d3a8f0afe5c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1490
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Double const is bogus and breaks the build on Clang 3.3.
Change-Id: I9f9394d17f66289ac74ae6dd48f3165483b72e9e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1489
Reviewed-by: Laszlo Papp <lpapp@kde.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
On XScale architecture, to write debug control register DCSR
and activate JTAG debug (ie. to choose Halt Mode), the
enabling can only be done while the board is held in reset
state (ie. PXAxx #RST line held low).
The current implementation writes to the register before
asserting the SRST line. Swap the order to activate the SRST
line before writing to DCSR.
Change-Id: I914b9d53d39bdeb5fe4ee5e11068cafafe0da4d2
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1458
Tested-by: jenkins
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Replace hexadecimal masks for vector catching with words
representing the caught exception, such as dabt for data
abort, etc ...
This way, the new xscale command is :
- xscale vector_catch
Reads back to the user the current vector catching status
- xscale vector_catch reset dabt pabt
Sets the caught vectors to data abort and prefetch abort
for example.
This is mostly taken from Cortex-M3 openocd code.
Change-Id: I66591d5796f0e07f0f31edc8d28722e1e48aa8c5
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/1456
Tested-by: jenkins
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This prevents segmentation fault that can occur on cortex_a targets if
gdb connection is established before it's halted and CPSR examined.
Change-Id: Id996200e0fd95440496509c1fecaabbdbf425e23
Tested-by: Henrik Nordstrom <hno@squid-cache.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
soft_reset_halt was only really intended for the older arm arch, eg. armv4/5.
Newer arch such as armv7m/mips do not need this as they have better alternatives.
Change-Id: Ifb360680b7e4bfa5365f3c79d82574bded952b45
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1442
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
mips_m4k_bulk_write_memory was only called from target_write_buffer as an
optimization when the word count was large enough.
Remove mips_m4k_bulk_write_memory from the target type, causing the default
implementation to call the regular mips_m4k_write_memory instead.
Perform the dispatch to bulk write in mips_m4k_write_memory, enabling the
optimization for target_write_memory() writes with size 4, in addition to
target_write_buffer() writes.
It also enables making the choice of bulk write vs regular write
specifically for the architecture and not relying on the generic target
code to make a sensible decision.
Change-Id: I295f21a67ceaa195802403f2518ea2e0a025c1c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1215
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
If mem_ap_sel_write_atomic_u32 fails then tmp_buff may not be released.
Detected by clang.
Change-Id: I3d5416bd47d0eea61f61ec02ac5e43c82f114108
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1433
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change scope of the variable gdb_reg_list_idx from global to module.
Change-Id: Ib8273c0769c11c1d5a338e4711efbddb8e8a0243
Signed-off-by: Jim Norris <u17263@att.net>
Reviewed-on: http://openocd.zylin.com/1441
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Add target code for Andes targets.
Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andes AICE uses USB to transfer packets between OpenOCD and AICE.
It uses high-level USB commands to control targets instead of using
JTAG signals. I define an interface as aice_port_api_s. It contains
all basic operations needed by target-dependent code.
Change-Id: I117bc4f938fab2732e44c509ea68b30172d6fdb9
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1256
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This file is used by all the Cortex-M family not just Cortex-M3.
Change-Id: Ie8680535b220c66bb8fcd862510407a46a73e8a0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1429
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Native compilation on RaspberryPi with
gcc (Debian 4.6.3-1) 4.6.3
Target: arm-linux-gnueabi
ends with error:
cortex_a.c: In function 'cortex_a8_read_apb_ab_memory':
cortex_a.c:2063:40: error: cast increases required alignment of target type [-Werror=cast-align]
cc1: all warnings being treated as errors
Also check for malloc failure.
This patch is compile-tested only.
Change-Id: I580c505424d03ac3a565de54182db22277c52ac1
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1369
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should cover all the cases when RESET_SRST_NO_GATING is set
without RESET_HAS_SRST. This might happen when RESET_SRST_NO_GATING is
automatically set by a target code (and not from tcl).
However, there're some other places (mips_m4k, arm7_9_common) where
adding RESET_SRST_PULLS_TRST would lead to trying to use SRST even if
it's not present. Currently it's impossible for the user to enable
that flag without enabling SRST.
Change-Id: Ib1c6f68feed0b8057d55afd5f260bb22ab332ced
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d9ba56c295 did a bunch of
renaming of cortex_a8 to cortex_a, including the names in config
files. However that introduced a regression as the name in target_type
struct remained unchanged.
This adds the last missing bit: actual renaming of the target name as
understood by OpenOCD.
Also change the (hopefully) last instance of using it in the supplied
config files, namely from imx6.cfg.
Change-Id: Ib9289fc6d946630133ec6e36c20015ccb50acf61
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1420
Tested-by: jenkins
Reviewed-by: Chris Johns <chrisj@rtems.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
There seems to be a few missing semihosting calls. I
am not sure why this one is actually missing, since it
seems simple enough to implement. It was tested using
an HTC HD7 connected to openocd through a "home brew"
ftdi 4232H board.
Change-Id: Ie17dc96c6d48227a3dc9ff1e21201a85498a10b1
Signed-off-by: Brandon Warhurst <roboknight@gmail.com>
Reviewed-on: http://openocd.zylin.com/1345
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Sometimes the target may have breakpoint registers set from a previous
debug session, we can either sync them or as we have chosen here clear them.
Change-Id: I439a623ebbf010246a70e5596d04aa7d546da731
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1363
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Seems commit fc2abe63fd caused a regression
in that the arm reg cmd no longer worked. The issue was caused because we
changed the value of ARM_MODE_THREAD which was being checked in arm_init_arch_info.
Change-Id: Id571d4ab336d1b0e2b93363147af245d24b65ca5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1362
Tested-by: jenkins
Reviewed-by: Luca Bruno <lucab@debian.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Now all the functions with only fetch accesses are modified.
The same delay between scans has been added to mips32_pracc_fastdata_xfer(), it should work
at the same scan rates as the other pracc functions, but it needs higher scan_delays
to work.
Change-Id: Ifb31d8ea6de9d22674385782913d221a2494dbbf
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1196
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Functions mips32_pracc_read_mem(), mips32_cp0_read() and mips32_pracc_read_regs() are now modified.
mips32_cp0_read() is very similar to mips32_read_u32() with one store access.
mips32_pracc_read_regs() is the only function that can not be executed from only one queue.
Now this function is modified to use reg8, it saves all the registers but does not restore reg8.
To remedy this, mips_ejtag_config_step() is called after mips32_save_context() in
mips_m4k_debug_entry(). Function mips_ejtag_config_step() is modified to use reg8 and
restore it from ejtag info instead of using DeSave for save/restore.
Change-Id: Icc224f6d7e41abdec94199483401cb512cc0b450
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1195
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Each pracc function defines a variable ctx of type struct pracc_queue_info.
To simplify the code tree auxiliary functions are defined: pracc_queue_init(), pracc_add() and
pracc_queue_free().
The second parameter in pracc_add() is the store address if the instruction is a store at dmseg,
otherwise it should be 0.
The code is executed by mips32_pracc_queue_exec(). If ejtag_info->mode is 0 mips32_pracc_exec()
is called and it should work like with current code.
To generate the delay between scans the number of clock ticks are calculated with the help of
jtag_get_speed_khz(). Due to delays in the execution of each single ftdi instruction the number of ticks
are higher as it should be, specially at higher scan rates.
mips32_pracc_read_u32() should now work with the new code.
Change-Id: I471590a4fc89b56af10bd46c48767b4c64de154f
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1194
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch and the following patches define another way of doing processor access without the need to read back
the pracc address as needed in current pracc code.
Current pracc code is executed linearly and unconditionally. The processor starts execution at 0xff200200
and the fetch address is ever incremented by 4, including the last instruction in the delay slot of the branch to start.
Most of the processor accesses are fetch and some are store accesses.
After a previous patch regarding the way of restoring registers (reg8 and reg9), there are no load processor accesses.
The pracc address for a store depends only on the store instruction given before.
m4k core has a 5 stage pipeline and the memory access is done in the 3rth stage. This means that the store access
will not arrive immediately after a store instruction, it appears after another instruction enters the pipeline.
For reference: MD00249 mips32 m4k manual.
A new struct pracc_queue_info is defined to help each function in generating the code. The field pracc_list holds in the
lower half the list of instructions and in the upper half the store addressess, if any. In this way the list can be used by
current code or by the new one to generate the sequence of pracc accesses.
For every pracc access only one scan to register "all" is used by calling the new function mips_ejtag_add_scan_96().
This function does not call jtag_execute_queue(), all the scans needed can be queued before calling for execution.
The pracc bit is not checked before execution, is checked after the queue has been executed.
Without calling the wait function the code works much faster, but the scan frequency must be limited. For pic32mx
with core clock at 4Mhz works up to 600Khz and with 8Mhz up to 1200. To increase the scan frequency a delay
between scans is added by calling jtag_add_cloks().
A time delay in nano seconds is stored in scan_delay, a new field in ejtag_info, and a handler is provided for it.
A mode field is added to ejtag_info to hold the working mode. If a time delay of 2ms (2000000 ns) or higher is set,
current code is executed, if lower, new code is executed.
Initial default values are set in function mips32_init_arch_info. A reset does not change this settings.
Change-Id: I266bdb386b24744435b6e29d8489a68c0c15ff65
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1193
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add command to fix CSW_SPROT in register AP_CSW.
This solves dap apmem access in non secure access.
Change-Id: I7cfcb6434d75f5cfd4a2630a059901cdeea010ce
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-on: http://openocd.zylin.com/1276
Tested-by: jenkins
Reviewed-by: mike brown
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After calling mips32_cp0_read() nothing has been queued, the call to jtag_exec_queue() is unnecessary.
Change-Id: Ie25438045a8e9b6b1b170df7b52609d45f284b5a
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In current devel code there are 3 functions (related to m4k code) that need to restore register 8 from pracc stack:
mips32_pracc_read_u32()
mips32_cp0_read()
mips32_pracc_write_mem_generic()
And mips32_pracc_read_mem() needs to restore regs 8 and 9 from pracc stack.
Values in this registers should be the same as read by mips32_pracc_read_regs() when entering debug
mode and can be modified by mips32_pracc_write_regs() when leaving debug mode.
There is no need to read their values from the processor registers every time.
The fields reg8 and reg9 are added to struct mips_ejtag to store these register values
and the call to mips32_save_context() is shifted in mips_m4k_debug_entry() in order
to store them before any other function needs to restore these registers.
For the same reason in function mips_m4k_step() the call to mips_m4k_set_breakpoint(), if needed,
should be made after calling mips_m4k_debug_entry().
For single word write the number of pracc accesses are now 9 or 8, from 13 or 12 in current code,
single word read takes now 10 instead of 12.
This patch is really the first in a set of patches for an alternate m4k pracc code
much faster that current code. At least for me with pic32mx works fine.
Change-Id: Ibd9df5e8b9f78ce05a180949ba6a561c761b61d6
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1146
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In this function after loading the handler code and the jump code there is a call
to wait_for_pracc_rw() to verify that a pracc access is pending.
Next the address is read to verify that the handler is running, the address should be at
fastdata area.
Next, another call is made to wait_for_pracc_rw(). This call is not needed, we now already
that a pracc access is pending.
Better we call this function before loading the end address to be sure it is loaded correctly.
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Change-Id: If311450ea634786fc28cf1a8e18ed24ce5257d20
Reviewed-on: http://openocd.zylin.com/1142
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
To show up the fail try to step with the core clock set to 31.25Khz
and with a ftdi/hs adapter or with a wiggler, -not with ft2232-.
The scan frequency should be set to 300Khz or higher, at lower frequency probably will not fail.
The code exits with error because the pracc address is at 0x0.
It also fails when using the "all" register, but in this case the code works without any message because the
pracc address is at 0xff202004 when it fails.
I never saw this fail with the core clock set to 500Khz or higher, but ...
The workaround simply puts a 1 ms delay after the execution of the DERET instruction.
Change-Id: I38e8c01a9c39aedd3282140543b83a0844d8ad29
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1139
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fixes system hang for devices that don't ignore
transactions to bad addresses.
Change-Id: Ia98344d7efc12951ef79dbc82b8f792b70a22cee
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/1115
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Moved JTAG code out of transport-neutral file (arm_adi_v5.c) into
transport specific file (adi_v5_jtag.c).
Added ap_block_read to dap_ops interface (arm_adi_v5.h) to support
the move.
Change-Id: I796d3984f138aad052b97c77ac9c12ffd1158f74
Signed-off-by: mike brown <mike@theshedworks.org.uk>
Reviewed-on: http://openocd.zylin.com/1277
Tested-by: jenkins
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Fritiofson
Paul Fertser
Spencer Oliver
Sergey A. Borshch
Franck Jullien
Hsiangkai Wang
Andrey Yurovsky
Oleksij Rempel
Oleksij Rempel
Bernhard Kiesbauer
Robert Jarzmik
Brent Roman
Jim Norris
Brandon Warhurst
Salvador Arroyo
Michel JAOUEN
Evan Hunter
mike brown