By a bit of code inspection it seems like all of these
instances of jtag_get_end_state() can be unambigously
replaced by constants.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
jtag_get/set_end_state() is now deprecated.
There were lots of places in the code where the end state was
unintentionally modified.
The big Q is whether there were any places where the intention
was to modify the end state. 0.5 is a long way off, so we'll
get a fair amount of testing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The SRST configuration options are not specific to JTAG, so this
command may be needed with non-JTAG debug sessions. Just move
the command to a different group.
(The TRST options are, however, clearly JTAG-specific, but for
compatibility, they're now left alone. The flags they control
could later be disabled in non-JTAG sessions.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_nsrst_assert_width" as "adapter_nsrst_assert_width",
and move it out of the "jtag" command group ... it needs to be used with
non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it
out of the "jtag" command group ... it needs to be used with non-JTAG
transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_khz" as "adapter_khz", and move it out of the "jtag"
command group ... it needs to be used with non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year. (We may want to
update it to include a nag message too.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
These routines apply to non-JTAG debug adapters too. To
reduce confusion, give them better (non-misleading) names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Streamline use of the layout: have the "ft2232_layout" command
look it up and save the result, instead of having a few different
chunks of code looking it up later, and saving just its name (which
is already part of the layout). This
- is cleaner
- reports errors sooner
- facilitates earlier adapter-specific setup
- removes unused "default to "usbjtag" logic
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove undesirable
- backslashes at end-of-line;
- initializations of BSS data to zero/NULL;
- overlong lines (80+ characters)
- whitespace issues
- brackets around single-line statements
And other minor issues reported by the Linux "checkpatch" utility
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch greatly simplifies the Versaloon driver:
- reducing the code size from more than 50K to less than 28K
- adding support for IR/DR scan with unlimited size
- using tap_get_tms_path and tap_get_tms_path_len.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This includes a driver and matching config file. This support needs to be
enabled through the initial "configure" (use "--enable-buspirate").
Signed-off-by: Michal Demin <michaldemin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We'll need to be able to work with debug adapter interfaces (drivers)
even when they're not used for JTAG ... for example, while there are
multi-transport drivers which support JTAG *and* several other
transports (or just one more, like SWD) there are also adapters
with more limited goals (and no JTAG support at all).
Start decoupling the two concepts ("debug adapter driver", "jtag")
by having two command groups, which initialize separately.
This will help us support OpenOCD sessions using only non-JTAG
transports, in which JTAG commands should not be registered.
Update docs to mention that the JTAG, SVF, and XSVF commands
won't work without a JTAG transport.
Note that at least commands working with SRST are still inappropriately
coupled to JTAG ... inappropriate because (a) SRST is not part of the
JTAG standard, for all that many platforms (like ARM) expect it; and also
(b) because they're used with non-JTAG debug and programming interfaces,
too. They should perhaps become generic "interface" operations at some
point. (Similarly with the clock rate to be used by a given adapter.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
How many bits to shift out before/after enabled tap not
in bypass is calculated outside the loop. This is more of
a demonstration of principle and to clarify code than
a performance optimisation as such. Follows up a bit
on the simplification work in jtag interface.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
In the code a single field was all that was ever used. Makes
jtag_add_ir_scan() simpler and leaves more complicated stuff
to jtag_add_plain_ir_scan().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
jtag_add_dr/ir_scan() now takes the tap as the first
argument, rather than for each of the fields passed
in.
The code never exercised the path where there was
more than one tap being scanned, who knows if it even
worked.
This simplifies the implementation and reduces clutter
in the calling code.
use jtag_add_ir/dr_plain_scan() for more fancy situations.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
after clocking out a tms sequence, then the TAP will be
in some state. This state is now handed to the drivers.
TAP_INVALID is a possible state after a TMS sequence if
switching to SWD.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The Redbee USB is a small form-factor usb stick from Redwire, LLC
(www.redwirellc.com/store), built around a Freescale MC13224V
ARM7TDMI + 802.15.4 radio (plus antenna).
It includes an FT2232H for debugging, with Channel B connected to the
mc13224v's JTAG interface (unusual) and Channel A connected to UART1.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Redbee Econotag is an open hardware development kit from
Redwire, LLC (www.redwirellc.com/store), for the Freescale
MC13224V ARM7TDMI + 802.15.4 radio.
It includes both an MC13224V and an FT2232H (for JTAG and UART
support). It has flexible power supply options.
Additional features are:
- inverted-F pcb antenna
- 36 GPIO brought out to 0.1" pin header
(includes all peripheral pins)
- Reset button
- Two push buttons (on kbi1-5 and kbi0-4)
- USB-A connector, powered from USB
- up to 16V external input
- pads for optional buck inductor
- pads for optional 32.768kHz crystal
- 2x LEDS on TX_ON and RX_ON
[ dbrownell@users.sourceforge.net: shrink lines; texi ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Implement the new TMS_SEQ command on FT2232 hardware.
Also, swap a bogus exit() call with a clean failure return.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For support of SWD we need to be able to clock out special bit
sequences over TMS or SWDIO. Create this as a generic operation,
not yet called by anything, which is split as usual into:
- upper level abstraction ... here, jtag_add_tms_seq();
- midlayer implementation logic hooking that to the lowlevel code;
- lowlevel minidriver operation ... here, interface_add_tms_seq();
- message type for request queue, here JTAG_TMS.
This is done slightly differently than other operations: there's a flag
saying whether the interface driver supports this request. (In fact a
flag *word* so upper layers can learn about other capabilities too ...
for example, supporting SWD operations.)
That approach (flag) lets this method *eventually* be used to eliminate
pathmove() and statemove() support from most adapter drivers, by moving
all that logic into the mid-layer and increasing uniformity between the
various drivers. (Which will in turn reduce subtle bugginess.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
FT2232-family chips have two or more MPSSE modules. FTDI documentation
calls these channels. JTAG adapter drivers thus need to be able to choose
which channel to use. (For example, one channel may connect to a board's
microcontroller, while another connects to a CPLD.)
Since each channel has its own USB interface, libftdi (somewhat confusingly)
identifies channels using INTERFACE_* symbols. Most boards use INTERFACE_A
for JTAG, which is the default in OpenOCD. But some wire up a different one.
Note that there are two facets of what makes a wiring "layout":
- The mapping between debug signals map and channel signals ... embedded
in C functions.
- Label used in Tcl configuration scripts ... part of the "layout" structure.
By letting the channel be part of the layout struct, we permit sharing the C
functions between Tcl-visible layouts, when those signal mappings are reused.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
zy1000 performance for GDB load went from 100kBytes/s
to 300kBytes/s @ 8 MHz by implementing the inner loop
of unack arm11 memory writes directly on top of the hw
fifo.
Profiling info:
78.57 0.77 0.77 arm11_run_instr_data_to_core_noack_inner
5.10 0.82 0.05 memcpy
4.08 0.86 0.04 jtag_tap_next_enabled
3.06 0.89 0.03 gdb_input
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This allows minidrivers to e.g. hardware accelerate memory
writes.
Same trick as is used for arm7/9 dcc writes.
Added error propagation for memory transfer failures in
code rearrangement.
Also the JTAG end state is not updated until after
the memory write run is complete.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Use labeled initializers in the table of layouts instead of
positional ones. This ls cleaner and less error prone, plus
it simplifies patches which add members to these structure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix an unused variable warning seen when building the parport driver
under FreeBSD.
Using information from Xiaofan Chen <xiaofanc@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Segger publishes some documentation on this protocol;
reference it, so future maintainers can know it exists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
srst_asserted and power_restore can now be overriden to do
nothing. By default they will "reset init" the targets and
halt gdb.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the target and openocd are idling, the log should normally
be silent at level 3. (Given no verbose logging options.)
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It is conceivable that there could be commands in the
queue when a speed change request comes in. Flush the
hw queue before changing speed. Not observed, found by
inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The very first command after init command should be "read target voltage".
This is a tweak for the Old Versaloon firmware. Without this, in most
most cases, it works. Under Ubuntu9.04, there is a chance that the USB
will fail. The problem disappears if I read target voltage first.
For the lastest Versaloon firmware, it's OK.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
flush JTAG FIFO before reset. Fixes RCLK problems observed
w/lpc2148, but really fixes a wider range of problems.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Øyvind Harboe
David Brownell
Spencer Oliver
simon qian
Michal Demin
Mariano Alvira
Edgar Grimberg