Targets "esp32c2" and "esp32c3" should not be mentioned in the doc
under "target types" because these are not standalone OpenOCD
targets.
They are merely a set of .cfg files which use the generic
"riscv" target.
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
Add a new riscv specific commands to disable triggers
Change-Id: Ic1842085aa66851c740e0abcbfbe0adbe930920e
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Extend riscv set_ebreak* commands.
Now it can be called without args to print current value.
riscv_ebreak* flags are moved to riscv_info struct.
Change-Id: Ib46e6b6dfc0117599c7f6715c7aaf113e63bd7dc
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
1. update RISCV_MAX_HARTS to 2^20 according to SPEC
2. remove RISCV_MAX_REGISTERS, it's not used anywhere anymore
3. add parentheses
Change-Id: Iadf0fa1ba3bbe5b9420b8430883e140db87f4f9e
Signed-off-by: Mark Zhuang <mark.zhuang@spacemit.com>
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this functionality allows to query if a target belongs to some smp group
and to dynamically turn on/off smp-specific behavior
Change-Id: I469453d95e7c1640a91bc60d80c854404e508535
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The bcm2835gpio driver preferred /dev/gpiomem for access to
memory mapped GPIO control and used /dev/mem as a fallback
only if it couldn't open /dev/gpiomem.
/dev/mem usually requires elevated rights or specific capabilities
of the opening process, so the fallback failed anyway.
Although /dev/gpiomem is the strongly preferred option with respect
to security, there could be also use cases which require /dev/mem
even if /dev/gpiomem is available (e.g. changing the GPIO pad
settings is necessary or testing/debugging OpenOCD).
It was difficult to handle such cases because they required
to block globally the system device /dev/gpiomem
(remove, rename or chmod).
Drop the fallback feature and select the memory device
by 'bcm2835gpio peripheral_mem_dev' configuration command.
Use /dev/gpiomem as a default.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I60e427bda795d7a13d55d61443590dd31d694832
Reviewed-on: https://review.openocd.org/c/openocd/+/7350
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The pads were configured at a wrong memory address
if /dev/gpiomem was mapped.
The pad setting registers are not accessible in mapped /dev/gpiomem,
disable the pads setting if the driver doesn't open /dev/mem.
While on it, do not fail the driver initialization if pad mapping fails
- just emit a warning and work with unchanged pad setting.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I0bce76cade8f7efd75efd9087a7d9ba6511a6239
Reviewed-on: https://review.openocd.org/c/openocd/+/7684
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This feature allows to transfer arbitrary data between host and
ESP32 via JTAG.
The main use cases:
1- Collecting application specific data
2- Lightweight logging to the host
3- System behaviour analysis with SEGGER SystemView
4- Source code coverage
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I95dee00ac22891fa326915a3fcac3c088cbb2afc
Reviewed-on: https://review.openocd.org/c/openocd/+/7163
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Checkpatch-ignore: GIT_COMMIT_ID
Waiting for running state was removed from handle_resume_command()
in commit a92d27afb0 ("very long and bad structured commit msg
without anything relevant to resume") around year 2008.
Update the doc accordingly.
Silent checkpatch or we have to copy 10 or more lines
of the old commit msg.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I3296cb2c29cf80aeed63eddd8fbf352edec778c1
Reviewed-on: https://review.openocd.org/c/openocd/+/7579
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The first part of the command should be only "riscv expose_csrs",
the $_TARGETNAME value is not necessarily "riscv", in fact it is
generally riscv.cpux.
Signed-off-by: Hang Xu <xuhang@eswincomputing.com>
The command 'svf' is the only command in OpenOCD that accepts
options in both forms 'option' and '-option'.
Deprecate the option format without the leading '-'.
Update the documentation and fix the on-line help.
While there:
- switch to use the new nvp.h helper;
- return ERROR_COMMAND_ARGUMENT_INVALID on invalid command args;
- fix some minor coding style rule.
Change-Id: I5b944403d92a3fa1e12d5faafc1d2a139bc16a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7534
Tested-by: jenkins
-noreset: when using several SVF input files in a sequence it is not always
desireable to have a JTAG reset between the execution of the files.
The -noreset option skips this unwanted reset.
-addcycles <x>: some tests rely on a certain number of extra clock cycles
between the actual JTAG commands. The -addcycles option injects a number
x cycles after each SDR instruction.
Signed-off-by: Kai Schmitz <kai.schmitz@advantest.com>
Change-Id: I31932d6041dbc803be00016cd0a4f23fb2e7dbe1
Reviewed-on: https://review.openocd.org/c/openocd/+/7433
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
A new FreeRTOS symbol xSchedulerRunning was added into the symbol list.
But the doc was not updated accordingly.
Signed-off-by: Chao Du <duchao@eswincomputing.com>
Change-Id: If1b18591e2681477ad96f1dea566cc2547097767
Reviewed-on: https://review.openocd.org/c/openocd/+/7531
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Calculate the FreeRTOS type sizes and offsets more adaptively.
The definition of TickType_t varies between different targets. And it is also related to configUSE_16_BIT_TICKS option.
Thus introduce a new command to make sure we are using a correct ticktype size.
Change-Id: I9e38b331a9f07b96eb9a2c259e32377fca0106ad
Signed-off-by: Chao Du <duchao@eswincomputing.com>
* redundant semicolon.
Change-Id: Ia21f0537e476099d8fe519ef78b3328d14123a38
* Update after review.
Change-Id: I1825185ec9b0557d7e01f34a8f366661b3734aa7
* update doc
Change-Id: I24b21c88b02ca3d76f1362f2545e86c068fc0ec6
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
Tim Newsome
Jan Matyas
Kirill Radkin
Evgeniy Naydanov
Ahmed BOUDJELIDA
Parshintsev Anatoly
Mark Zhuang
Laurent LEMELE
Daniel Anselmi
iosabi
Erhan Kurubas
Tomas Vanek
Hang Xu
Antonio Borneo
Kai Schmitz
Chao Du
Chao Du