This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The Atmel SAMR21 is a Atmel SAMD21 with an Atmel RF233 in one package (two
dies). Tested with the SAMR21 Xplained Pro eval kit.
Change-Id: I1d79ea05834b925d7ec810527206fe86854e684b
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2194
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Gumstix AeroCore board [1] contains a STM32F427 microcontroller.
Schematics for this board will also be made available [2].
The JTAG interface for this chip can be accessed via a USB connection
provided by an FTDI chip (0403:6011).
[1] https://store.gumstix.com/index.php/products/585/
[2] https://pubs.gumstix.com/boards/AEROCORE
Change-Id: I0bf3bb525f51528bedd807b1f7210b09ef2e1015
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Reviewed-on: http://openocd.zylin.com/2117
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Also add the board to the firmware recovery script.
Change-Id: I4f9c895dae171df7249e3b1c0563b288518b9fe0
Signed-off-by: Lee Bowyer <lee@sodnpoo.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch allows users to specify TAP_TYPE from
the command line when using or1k_generic.cfg.
Change-Id: I9f4b7d8e4867658fa34bb4e92fc3a5f25227df11
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/2056
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds support for the am43xx SoC and the AM437x GP EVM and AM438x
ePOS EVM.
Change-Id: I09cbb09072f38e0e08fdd520dedb6e67d45056be
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2047
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reported and tested by Gracana on IRC.
Change-Id: If0524d2d627d566e8b5e1d00784dd7556f44b125
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2036
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for Broadcom's dual A9 mobile SoC and its reference board.
Change-Id: Ia145b120043bddc89c44726066023154ae390788
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-on: http://openocd.zylin.com/1926
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
flash: at91sam4: add support for the SAMG53 family (this also covers the
SAMG51). The SAMG5x parts have an EEFC (enhanced embedded flash controller)
which seems to be identical to the EFC that the sam4 driver supports.
Add a script for the Xplained Pro G53 board, this has the onboard CMSIS-DAP
debugger and a SAMG53N19. Tested on this board and chip combination.
Change-Id: I12af50402cd2069b3c7380d92e6fe54816d6c045
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1974
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Intel Quark X10xx SoC debug support added
Lakemont version 1 (LMT1) is the x86 core in Quark X10xx SoC
Generic x86 32-bit code is in x86_32_common.c/h
Change-Id: If2bf77275cd0277a82558cd9895b4c66155cf368
Signed-off-by: adrian.burns@intel.com
Reviewed-on: http://openocd.zylin.com/1829
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with SAMD21J18A on the SAMD21 Xplained Pro board.
Change-Id: Ice9ebcd229ed038b3193baf92d910f9256d7ce91
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1873
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These kits feature a CMSIS-DAP compliant debugger and so have been added
as part of the pending support.
Currently the flash drivers for the L8 and D20 are wip.
One issue this implementation of CMSIS-DAP raised is that it supports
512byte HID reports, however using the current HIDAPI we have no cross platform
way of querying this info. Long term we plan to add this support to HIDAPI.
Change-Id: Ie8b7c871f58a099d963cd71a9f8a0105a38784e9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1625
Tested-by: jenkins
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
Tested flashing a real v1.1 device.
Change-Id: Ie0d202b9fded8b92e731d93e0ef17be415a75fc8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1852
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".
The RAM setup is not done as it would require considerable efforts
without much practical gain.
The only issue I noticed so far is that "reset" doesn't actually reset
the chip.
Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.
Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.
Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the TMS570 Cortex-R4 MCU from TI and their USB stick
development kit, TMDX570LS31USB. Tested attaching, reset/halt/run, and
reading and writing memory and registers.
Change-Id: I12d779cef0c2b834f9bcf722307f35677cc4bd8f
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1788
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Almost the same as the LM4F120 LaunchPad but the chip is using the new
naming scheme (Tiva C series), supports USB OTG and has some new PWM
hardware blocks.
Change-Id: I6a7b2df76768766471f366cddaf64df3cc63f5f2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1647
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This commit adds two tcl configuration files, one for the Altera
Cyclone V SoC series, and one for the SoCkit development board.
The board configuration is able to halt and resume the cpu cores,
and dump register contents etc. It has not been fully tested, however.
Change-Id: Id3f18c3408975cf986a5f5aec410b5b13240c35e
Signed-off-by: Brad Riensche <brad.riensche@gmail.com>
Reviewed-on: http://openocd.zylin.com/1494
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for DENX M53EVK board and it's integrated on-board
JTAG adapter using FT2232H.
Change-Id: I022dcafa7799bb84a7873ba67ed82f1e49094320
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1461
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Pull the jtag_rtck setting from imx51.cfg and imx53.cfg . Since
not all boards using these CPUs do support RTCK signal, move the
configuration of RTCK into board files.
Change-Id: I632c5d38e00ada8779a451cd26428fd122452001
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1460
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add target code for Andes targets.
Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This part has 16k ram so make it all available.
Change-Id: Ifeb7bc850bfe4f68d0affb8f6a0931b4327e7257
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1006
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
This config file is intended as an example of how to
use the lpcspifi flash driver, but it should be functional
for most LPC1850 boards utilizing SPIFI flash.
Change-Id: I855854282336701fd210134497ce014017f3aaec
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add cfg files for Hitex LPC1768 Stick
Website: http://www.hitex.com/?id=1602
This board has a FTDI2232D as JTAG interface, using the
same layout as the Hitex STM32-PerformanceStick but with
different USB PID.
Main MCU is a LPC1768 from NXP.
The interface config uses the ftdi driver instead of ft2232.
The corresponding ft2232 layout would be "stm32stick".
Change-Id: I1fd15588c5af35f7d51777d1ad958cc1dc72c6f7
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/763
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Eldar Khayrullin
Andrey Smirnov
Paul Fertser
Fredrik Hederstierna
Thomas Schmid
Franck Jullien
Nemui Trinomius
Marco Cruz
Ash Charles
Lee Bowyer
Tim Sander
Felipe Balbi
Jens Hoffmann
Tim Kryger
Tom Rini
Andrey Yurovsky
Adrian Burns
Spencer Oliver
Sergio Chico
Brad Riensche
Marek Vasut
Hsiangkai Wang
Gianluca Renzi
George Harris
Joerg Fischer