Pprogram that loads another program into memory is actually writing the
D- side cache.
The instructions it has loaded can't be executed until they reach the
I-cache.
After the instructions have been written, the loader should arrange to
write back any containing D-cache line and invalidate any locations
already in the I-cache.
For the MIPS Architecture Release2 cores, we can use synci command
that does this job.
For Release1 we must use "cache" instruction.
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
accidentally invoked return jtag_execute_queue() in the
middle of a fn. Hmm.... I would have expected gcc or
at least lint to catch this.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove extra \n from LOG_DEBUG, LOG_INFO, and LOG_WARNING messages
Remove LOG_INFO_N
LOG_INFO_N was only used once and had a \n at the end
Change LOG_USER_N calls that end with \n to LOG_USER
Add a working area that is preserved between calls to
mips_m4k_bulk_write_memory - this gives us a speed increase
of approx 3kb/sec during flash writes to the pic32mx.
This area is released during a resume/reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- add mips support for target algorithms.
- added handlers for target_checksum_memory and target_blank_check_memory.
- clean up long lines
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- add target_to_mips32 and target_to_m4k to match test of codebase.
- mips32_arch_state now shows if processer is running mips16e isa.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
If fastdata access fails, then fallback to default mips_m4k_write_memory
Remove unnecessary fastdata loader verify check
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This will allow data to be allocated in read only
memory instead of on the stack. Speeds things up
and reduces stack usage.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
- all the register now can be written to, including the special CP0 regs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1169 b42882b7-edfa-0310-969c-e2dbd0fdcd60
ejtag_info->ejtag_ctrl variable. It was being overwritten by the value read back from the EJTAG CONTROL register. Because of the way this register works you do not want to use the value returned to write the register, you always want to write the bits explicitly.
The second patch just reduces the DMA retries to 0 in anticipation of removing the retry code altogether.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1049 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Spencer Oliver
Øyvind Harboe
Drasko DRASKOVIC
Freddie Chopin
Eric Wetzel
Spencer Oliver
Antonio Borneo
David Claffey
Zachary T Welch
Jerry Ling
zwelch
duane
oharboe
ntfreak