- The guess-rev.sh script is now a tweaked version of "setlocalversion" as
seen in Linux, U-Boot, and various other projects. When it finds source
control support (git, hg, svn) it uses IDs from there. Else (specific
to this project) it reports itself as "-snapshot", e.g. from gitweb.
I verified this new "guess-rev.sh" script runs under Cygwin.
- Also update the generic version strings to be like "0.3.0-dev" (during
development) instead of the very long "0.3.0-in-development". These also
show up in the PDF docs. For better tracking, we might eventually change
these strings to include the version IDs too.
- Change the startup banner version strings so they include the guess-rev
output. Development and release versions with GIT will be like
Open On-Chip Debugger 0.3.0-dev-00282-g7191a4f-dirty (2009-10-05-20:57)
Open On-Chip Debugger 0.3.0 (2009-10-05-20:57)
instead of the previous SVN-specific (even when using git-svn!)
Open On-Chip Debugger 0.3.0-in-development (2009-10-05-01:39) svn:exported
Open On-Chip Debugger 0.3.0 (2009-10-05-01:39) Release
git-svn-id: svn://svn.berlios.de/openocd/trunk@2809 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Bugfix the error message so it shows the disliked value, and add
a debug message showing each TAP's IR capture value, all N bits.
This just changes diagnostics ... it still ignores the parameters
given to us at TAP declaration time.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2801 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The model is that this fires after scanchain verification, when it's
safe to call "jtag tapenable $TAPNAME". So it will fire as part of
non-error paths of "init" and "reset" command processing. However it
will *NOT* trigger during "jtag_reset" processing, which skips all
scan chain verification, or after verification errors.
ALSO:
- switch DaVinci chips to use this new mechanism
- log TAP activation/deactivation, since their IDCODEs aren't verified
- unify "enum jtag_event" scripted event notifications
- remove duplicative JTAG_TAP_EVENT_POST_RESET
git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- don't needlessly export this function
- handle "case 0" debug method-of-entry better (silent by default)
The "case 0" is a valid debug entry mode so it doesn't deserve the
warning int now gets. But it probably means that OpenOCD confused
itself somehow; or that it confused the ARM9EJS target.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2799 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- ETB
* report _actual_ hardware status, not just expected status
* add a missing diagnostic on a potential ETB setup error
* prefix any diagnostics with "ETB"
- ETM
* make "etm status" show ETM hardware status too, instead of
just traceport status (which previously was fake, sigh)
- Docs
* flesh out "etm tracemode" docs a bit
* clarify "etm status" ... previously it was traceport status
* explain "etm trigger_percent" as a *traceport* option
ETM+ETB tracing still isn't behaving, but now I can see that part of
the reason is that the ETB turns itself off almost immediately after
being enabled, and before collecting any data.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2790 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Don't issue needless JTAG resets ... only do them after
errors. Normal exit now leaves every TAP in BYPASS.
- Fix an unlikely memory leak on one fault path.
- Remove the oddball limitation that invalid capture LSBs
trigger errors only for TAPs that support IDCODE.
Re the JTAG reset: there are too many of them, and they can
(and do!) change system state. So the needless ones should
get removed. This one was especially pointless.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2777 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Commands were supposed to have been "arm11 memwrite ..."
not "memwrite ..."
- Get rid of obfuscatory macros
- Re-alphabetize
- Add docs for "arm11 vcr"
git-svn-id: svn://svn.berlios.de/openocd/trunk@2776 b42882b7-edfa-0310-969c-e2dbd0fdcd60
When the OpenOCD server starts up it records its state as TAP_RESET,
even though it could be anything. Then when it starts to examine
the scan chain, it calls jtag_add_tlr() which sees it doesn't have
any work to do, and so it does nothing. This can make the next
operations fail because they start from the wrong TAP state...
Instead of caring about the current recorded state, always enter
TAP_RESET by forcing five clocks with TMS high.
(NOTE: it seems most other JTAG adapter drivers have this same bug.)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2763 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Change the handling of the "-ircapture" and "-irmask" parameters
to be slightly more sensible, given that the JTAG spec describes
what is required, and that we already require that conformance in
one place. IR scan returns some bitstring with LSBs "01".
- First, provide and use default values that satisfy the IEEE spec.
Existing TAP configs will override the defaults, but those parms
are no longer required.
- Second, warn if any TAP gets set up to violate the JTAG spec.
It's likely a bug, but maybe not; else this should be an error.
Improve the related diagnostics to say which TAP is affected.
And associated minor fixes/cleanups to comments and diagnostics.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2758 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Ready for discussion and tiny patches that tries out this scheme.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2755 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Added gdb_sync feature that allows GDB to sync up to target state.
Issue "monitor gdb_sync" and the next stepi, will return immediately
with updated register values to GDB.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2754 b42882b7-edfa-0310-969c-e2dbd0fdcd60
make sure that when there are two or more targets, their
various pre/post event reports are correctly ordered.
Previously, only the first target always saw its "pre"
method before SRST was asserted or deasserted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2753 b42882b7-edfa-0310-969c-e2dbd0fdcd60
only expose the registers which are actually present. They
could be missing for two basic reasons:
- This version might not support them at all; e.g. ETMv1.1
doesn't have some control/status registers. (My sample of
ARM9 boards shows all with ETMv1.3 support, FWIW.)
- The configuration on this chip may not populate as many
registers as possible; e.g. only two data value comparators
instead of eight.
Includes a bugfix in the "etm info" command: only one of the
two registers is missing on older silicon, so show the first
one before bailing.
Update ETM usage docs to explain that those registers need to be
written to configure what is traced, and that some ETM configs
are not yet handled. Also, give some examples of the kinds of
constrained trace which could be arranged.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2752 b42882b7-edfa-0310-969c-e2dbd0fdcd60
system, removes 20 non-existent registers ... but still includes
over 45 (!) ETM registers which don't even exist there ...
- Integrate the various tables to get one struct per register
- Get rid of needless per-register dynamic allocation
- Double check list of registers:
* Remove sixteen (!) non-registers for data comparators
* Remove four registers that imply newer ETM than we support
* Change some names to match current architecture specs
- Handle more register info
* some are write-only
* some are read-only
* record which versions have them, just in case
- Reorganize the registers to facilitate removing the extras
* group e.g. comparator/counter #N registers together
* add and use lookup-by-ID
git-svn-id: svn://svn.berlios.de/openocd/trunk@2751 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Add a header comment
- Line up the ETM context struct, pack it a bit
- Remove unused context_id (this doesn't support ETMv2 yet)
- Make most functions static
- Remove unused string table and other needless lines of code
- Correct "tracemode" helptext
Also provide and use an etm_reg_lookup() to find entries in the ETM
register cache. This will help cope with corrected contents of that
cache, which doesn't include entires for non-existent registers.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2750 b42882b7-edfa-0310-969c-e2dbd0fdcd60
didn't turn up earlier. Is everyone still using gcc 3.x? Or is the x86
version of gcc 4.x much more relaxed?
git-svn-id: svn://svn.berlios.de/openocd/trunk@2749 b42882b7-edfa-0310-969c-e2dbd0fdcd60
of a (NOR) flash chip: allow passing "last" as an alias
for the number of the last sector.
Improve several aspects of error checking while we're at it.
From: Johnny Halfmoon <jhalfmoon@milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2746 b42882b7-edfa-0310-969c-e2dbd0fdcd60
garbage after the expected data (from the TAPs' BYPASS or IDCODE
registers).
NOTE that there was previously some code that looked like it was
trying to do this ... which didn't work, because it was looping
over the list of expected TAPs, and never checked *after* that
list completed! That could hide some *nasty* reset issues...
Also replace a now-obsolete scanchain length test with one that
behaves correctly; and update reporting of unexpected IDCODEs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2739 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch modifies an error message which, in its original state,
I find somewhat unhelpful. So a small hint was added.
Signed-off-by: Johnny Halfmoon <jhalfmoon at milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2738 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Shrink messaging during resets, primarily by getting rid of
"nothing happened" noise that hides *useful* information.
- Improve: the "no IDCODE" message by identifying which tap only
supports BYPASS; and the TAP event strings.
Related minor code updates:
- Remove two needless tests when examining the chain: we know
we have a TAP, and that all TAPs have names.
- Clean up two loops, turning "while"s into "for"s which better
show what's actually being done.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2736 b42882b7-edfa-0310-969c-e2dbd0fdcd60
for disabling TAPs. We don't actually know how to make any
JRCs which do that yet; but when we do, this will matter.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2735 b42882b7-edfa-0310-969c-e2dbd0fdcd60
and Tcl/external):
- Reorder so *both* paths (TCK/TMS or TRST) can enable TAPs with
ICEpick ... first C code flags TAPs that got disabled, then call
any Tcl code that might want to re-enable them.
- Always call the C/internal handlers when JTAG operations can be
issued; previously that wasn't done when TRST was used.
Plus some small cleanups (whitespace, strings, better messaging
during debug and on some errors) to reset-related code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2730 b42882b7-edfa-0310-969c-e2dbd0fdcd60
oharboe
dbrownell
mlu
ntfreak