STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Avoid annoying "deprecated" messages in the scripts
distributed with OpenOCD code.
Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5287
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently the code assumes the adapter uses raw SWD, and the expected ID
code of the CPU is even wrong. An adapter speed is also not specified.
All these prevents the config file to be used with ST-Link.
Fix the config file, to allow it to be used with ST-Link.
Change-Id: I1244320fabfe8ee23da5a56a592dbeddc72cc8d5
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-on: http://openocd.zylin.com/5297
Tested-by: jenkins
Reviewed-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32H7x7 and STM32H7x5 devices contains two cores : CM7 + CM4
The second core creation is only done when
* DUAL_CORE variable is set to true
* non HLA interface is used
A second check for the second core existence is done in cpu1 examine-end
Once the second core is detected it gets examined.
Furthermore, the script provides a configurable CTI usage in order to halt
the cores simultaneously.
Tested on Rev X and V devices.
PS: the indentation was a mix of spaces and tabs, all changed to tabs.
Change-Id: Iad9c30826965ddb9be5dee628bc2e63f953bbcb8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The STM32H7 has three access ports. The DBGMCU component is available
through AP0 at 0x5C001000 and through AP2 at 0xE00E1000. Using the
latter is preferable for early configuration because it works in all
power states and while SRST is asserted, whereas the former does not.
Change-Id: Iaf8f01d769efb6655040060a8e1e951e1f7e50ab
Signed-off-by: Christopher Head <chead@zaber.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4742
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Correct check for end-of-region is:
$BASE + $LEN > $ADDRESS
And it is currently (wrongly) calculated as:
$ADDRESS > $BASE - $LEN
Change-Id: If10bfee19b0c7dbc085731ac1eda943f5d8a36a3
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4798
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is not flash bank support at the moment.
Change-Id: I833c009d9d21cdeb70b57d67eb557d50ed0fb4de
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5205
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also
adds configuration file for SSE-200 based Musca A board. Flash programming
support for Musca A QSPI flash is still not functional. This configuration
will be updated once that support lands into OpenOCD.
Please refer to ARM documentation for more information about SSE-200 and
Musca A.
Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/5006
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The V3M SoC is R8A77970 while the V3H SoC is R8A77980 . Update the
CHIPNAME and swap the SoCs to keep the list sorted.
Change-Id: I7e1777c0c7181e5e0beac98333f2047cb443d0df
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5140
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H target.
This is an SoC with one Cortex A9 ARMv7a core and
up to 10 MiB of on-SoC SRAM.
Change-Id: I20fd54b385fe1ba1cc325451c3fdfa3a835d4884
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H GR-Peach board,
which is a cheap development kit for the RZ/A1H SoC.
Change-Id: I7f5596ae47e6dff8e6d06cffd4dddca20f57d0ca
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The commands prefixed with "ocd_" are removed.
Remove them from configuration files.
Change-Id: Ib44627ee17a39f3d06b479507ab5a025073bf9a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5090
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* Add mem_ap for direct access to axi bus (without halting cpu)
* Mark m4 core with -defer-examine because it's not used by default
* Make a53.0 default target since it's the boot core
Change-Id: Id031533c5d4af346eb08a9ac2532fa1bca602913
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5036
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 the 6UL 6ULL 6ULZ chips are based on Cortex-A7
which is at a different address so a custom script is required.
Tested on imx6ull-14x14-evk
Change-Id: I72822d2241045c318389fadbc66d7aaabaaf4cb5
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5040
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 a Cortex-M4 was added with a second CoreSight
DAP so a separate script is required.
Tested on imx6sx-sdb running linux
Change-Id: I1561910b233015f42508f341175822c0827655ec
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5041
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike imx7d/solo supported by imx7.cfg the M4 core is on a different AP
and is always running by default so no -defer-examine is required.
There is also only one Cortex-A7
Tested on imx7ulp-evk
Change-Id: Ifa923d1b9a372c788e6654bc2233fd4d9073a32d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5043
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add a config to access the Amazon Kindle Model No. D00701 and D00801.
Both ebook readers are based on a Freescale i.MX31. A JTAG interface is
included in a 40 pin FFC connector marked "J9" on both variants.
Change-Id: I58bb1ded3d6706bc3798af488ca8bafb7dc45225
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3956
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Copy all SJC TAPIPs from imx6 reference manuals.
Some imx6 chips are based on Cortex-A7 or have an additional Cortex-M4
and need separate scripts.
Change-Id: I3b07d94058c2c5e6313cfc8bb43134a90682a62e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5034
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
OpenOCD scripts are usually indented with 4 spaces but here there are 8.
Change-Id: Iaad53e3b377d246d99119bb7bb5fd75d4422f564
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5039
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Looking through imx6 manuals all of them claim that "In follow-on
silicon revisions the ID value is subject to change by incrementing the
first nibble".
Handle this by passing -ignore-version to jtag newtap command.
Change-Id: I7fc4779f9757d527ea20a5174a8c90f919580013
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This allows bus access even when CPU is off.
Change-Id: I2d5c5581cd0169aecb92ac7b610810988a8dcef4
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5032
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch remaps the Flash over ITCM region as virtual to ensure that
any breakpoint placed in this area will be automatically set as an
hardware breakpoint. This patch is a fix to a regression introduced with
changes #4429.
Change-Id: I03d46d8537ef06b33a3d4a2328274667c6481969
Signed-off-by: Rocco Marco Guglielmi <roccomarco.guglielmi@gmail.com>
Reviewed-on: http://openocd.zylin.com/5097
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The imx8m also has a Cortex m4 so add a target for it.
Change-Id: I2abf62b6232c547fe9b12507f459835b11c63a6d
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-on: http://openocd.zylin.com/4501
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The OTP is part of the flash memory. It has 512 (1024 for F7) bytes
and is organized in 16 sectors with 32 (64 for F7) bytes each.
The OTP is exposed as separate flash bank 1 and can be used
with the usual flash commands.
Writing the OTP can be done as follows:
> stm32f2x otp 1 enable
> flash write bank 1 foo.bin 0
> mdw 0x1fff7800 4
> verify_image foo.bin 0x1fff7800
> stm32f2x otp 1 disable
Note: This patch is largely a rebase/cleanup of a patch
from 2012 by Laurent Charpentier and he did most of the work.
No new Clang-Analyzer warnings.
Change-Id: I5e6371f6a7c7a9929c1d7907d6ba4724f9d20d97
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The new Microchip (former Atmel) series powered by Cortex-M4 looks
very similar to older M0+ powered SAM D2x at the first sight.
Unfortunately the new series differs a lot in important details.
NVMCTRL has different register addresses, moved important bits
and even changed binary command set. An universal driver for all SAM D/E
would be very complicated. That's why a new driver was derived.
Tested on Microchip SAM E54 Xplained Pro kit (board cfg included).
Adjusted for the restructured dap support.
Checked by valgrind and clang static analyzer.
Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4272
Tested-by: jenkins
Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
The original script was broken by changes to the Cortex-A code. The
recent introduction of the mem_ap target provided a new mechanism to
allow the script to be fixed. This also adds an example board script
for the ADSP-SC584-EZBRD.
Change-Id: I36bc1ac6b6c036539f4175f1e65223ba10a35355
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4855
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The xilinx_ultrascale.cfg target is actually the configuration for a
ZynqMP, which is a combination of an UltraScale+ FPGA core and a quad
core A53. Update the filename/comments to reflect this, and include
the tap IDs for all known FPGA cores for this part.
Change-Id: I70dfcc99861a482b83b6a795e83021d9cf1fe047
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4850
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Agama family of devices (CC26x2/CC13x2) required an
additional bit to be set when adding the core's TAP into
the scan chain. The cancel reset bit 0x10000 tells the
ICEPick to take the bus out of reset so that the other
bits will take effect. This bit is a NOP on other devices
and ICEPicks, so the change shouldn't adversely affect
other devices.
Change-Id: I9245eef0936ea7eea28ae84ab5e8ce05fa63af40
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
original CC3200 launchpad works only with ti-icdi driver
which stopped to work after merging to master commit
d02de3a8a9
Change-Id: I247b5d99831fa744de1fdc5b8a7cffdf49fe953c
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/4792
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1
Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.
Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for reading halfword values from memory. This
command compliments existing support for writing halfwords (mwh).
Change-Id: I8ec628e65c05a7f00aa57e3af0f228eb8bd4d14e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4781
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since commit bae76053dc
gdb-attach event is defined as halt by default.
Remove useless and in case of bcm281xx wrong definitions of the event.
Change-Id: I8e69780a93722eb9392673303f54d502e71eceb6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4763
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
The reset_config line in the config file does not actually set
connect_assert_srst (the default is connect_deassert_srst), but it reads
as if it does. Clarify that the target is compatible with
connect_assert_srst, without suggesting that the file actually sets it
to that value.
Change-Id: I14e9445ab282d386b5d0055f6adf03d7c8878a8c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4743
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32h7x.cfg does not specify connect_assert_srst or
connect_deassert_srst in its reset_config. The comment claims that it
will therefore connect in reset. However, per the manual, the default
configuration is actually connect_deassert_srst, not
connect_assert_srst. In actual fact, connect_assert_srst does not work
on the STM32H7 because, while SRST is asserted, everything on the AXI
bus is inaccessible. The CPU core is accessible, but since the
examine-end event handler also pokes at the DBGMCU peripheral, that will
fail in connect_assert_srst mode. So using connect_deassert_srst is
appropriate, so fix the comment accordingly.
Change-Id: If3e32e871fb19cc61183bdf911b7c5efd80b62e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4741
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When using stlink for CM7 targets we have to rely on its firmware
to do the right thing as direct DAP access is not possible.
Change-Id: Ieee69f4eeea5c911f89f060f31ce86ed043bdfd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4732
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tarek BOCHKATI
Antonio Borneo
Icenowy Zheng
Christopher Head
Piotr Kasprzyk
Andreas Färber
Felipe Balbi
Al Dyrius
Marc Schink
Caleb Szalacinski
Omair Javaid
Marek Vasut
Leonard Crestez
Alexander Kurz
Rocco Marco Guglielmi
Angus Ainslie
Moritz Fischer
Tomas Vanek
Peter Lawrence
Jonathan McDowell
Edward Fewell
Rod Boyce
Oleksij Rempel
Jean-Christian de Rivaz
Jiri Kastner
Steven Stallion
Paul Fertser