This driver implements a bitbang jtag interface using gpio lines exported via
sysfs.
The aim of this driver implementation is to use system GPIOs but to avoid the
need for an additional kernel driver.
A config suitable for RaspberryPi is included.
Change-Id: Ib2acf720247a219768d1cbfeebd88057ed2d7b8b
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Reviewed-on: http://openocd.zylin.com/762
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stlink interface currently does not support 16bit read/writes.
Until a fix is included we issue a error that this is unsupported.
Change-Id: I4552cf2bd3b29e90ecc905325b743c08e2b92d67
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/808
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In at91sam3.c for Atmel SAM3 flash support, there are arithmetic errors in the functions sam3_page_read() and sam3_page_write().
Address locations are computed incorrectly due to an extra addition operation. This leads to memory locations being skipped during
flash writes and reads.
Smaller programs are written successfully into flash, with memory gaps, while larger programs of legitimate size fail because the
skipped memory is not utilized and therefore unavailable.
The changes address this condition, and have been tested with an Atmel SAM3X-EK evaluation board.
Change-Id: I9ea3b9ed0130b71cbc32b2294e31a6a2bc71b47a
Signed-off-by: Chuen Chou <zhouquan27@gmail.com>
Reviewed-on: http://openocd.zylin.com/806
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the target does not support SYSRESETREQ we fall back to using VECTRESET.
This however does not reset the peripherals and we issue a warning to the user
to suggest using a reset-init script.
Also suggest that using hardware srst will give them the same functionality
as using SYSRESETREQ.
Change-Id: Ie1781c4b849fed66c52222e6539735537c879fb3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/802
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In function pic32mx_write_block() if the parameter
offset is not a multiple of row size the row offset
(offset % row_size) will be ignored by the flash
controller, shifting the code to the beginning of
the row.
Word programming gets it right.
Change-Id: I134913e3d533688f791bbcb0c6e8983524197f3c
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
So the user can view the current port number these cmds were changed to COMMAND_ANY.
However this means that the user can also attempt to change the port number after init,
even though this is not supported. Issue a warning that this is not supported.
Change-Id: I3d20dcd81277e7d994240a8e314f27672ff760c4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/788
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The last bit of a scan is clocked during TAP movement so it's necessary
for the last field to have at least one bit. Strip trailing empty fields
and make sure the TAP is not affected if there's nothing to scan. Clients
probably shouldn't add empty fields so add a debug message to be able to
track and fix them.
Change-Id: I27552568bc11146570b9b99ed8a1ae81b5fb2c50
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/794
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
When there's no data to scan in or out, we still use the clock data out
command and fill the buffer with zeroes, so make sure the buffer is
checked for available space.
Change-Id: Ia6005c40c81f7fdb89379f1b5023fe383184d210
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/793
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently only the adapter speed is printed, which can be rather misleading
when DEBUG_INFO is disabled, all the user sees is
6000 kHz
instead lets print
adapter speed: 6000 kHz
Change-Id: I8f02a63f47344457e3c3d0a6774157fa18206440
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/797
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add single "scripts" folder to search path for Windows OpenOCD builds
that don't use cygwin
bin/openocd.exe
scripts/interface/dummy.cfg
scripts/target/at91eb40a.cfg
Do some refactoring of current code (thx to Andreas).
Change-Id: Idbb08d1368b06f25da44f4f9ab1511db992b1724
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/785
Tested-by: jenkins
Offset calculation into buffer was wrong and code would read outside buffer
if count was not a multiple of four.
Change-Id: Ied625b10221423d5a5f25d27ce1edd8c2c3eca8a
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/749
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The number if longwords or "sections" (Freescale term) written for a Kinetis
flash write (4, 8, or 16 bytes depending on the part density/granularity) are
now rounded up to ensure there are no truncations when the desired write is
not a multiple of the minimum write size.
Change-Id: I8db40a8769d8ac5393a46cbf4e5ff0df82faf916
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/738
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
For example in a pic32mx220, pic32mx unlock don't work
if adapter_khz is set to 5000 or more.
A short delay after asserting reset fix the problem.
Change-Id: I62e493edfcea585c36c8de77a969cebac7227b96
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/790
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Always scan out all bits, but make sure only the allowed number of bytes
end up in the caller-provided buffer. Discard the rest by adding another
scan field when size < 4.
Rewrite the endianness callback to avoid reading outside allocated memory.
Make it directly usable as a callback without the need for a wrapper. Move
the shared callback to a more suitable home in arm7_9_common.
This fixes the regressions introduced in commits
991ed5a2b6cb90d32e38
and
c3074f377c
Change-Id: Ia8bde8c5a9844e89a1d6c0bc8534cd26f02f8d11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The function wait_for_pracc_rw() fails if Pracc bit is 0.
The variable ejtag_ctrl is loaded with the content of the
control register in the first scan.
In the second scan Pracc bit is scanned out as 0, letting
the proccesor go. The result is unpredictable.
All the strange data corruption when scanning at certain
frequencies, or the strange delays needed when entering
or leaving fasdata area are retated to this bug.
Now the code works at any scan frequency, tested up to 15000Khz
and indepently of processor speed, tested at 31.25Khz and 4/8Mhz.
Change-Id: Iedfd81d06d6af4bc738a521f720e42323025b268
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/769
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
working_area::user has never been used so lets remove it.
Change-Id: I1200311b34248549c1fe30c9f675e6129b7bebee
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/781
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Retest the condition when needed, instead of abusing the common_magic
field as a flag. There are only two options here. Either it's an armv7m or
it's another arm. is_arm(...) will return true even for armv7m, so it's
imperative to check in the right order.
Change-Id: Ic227f19f7babf1b0b0fe075f9a3abc4eabc7d5f1
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By Initialising the param_table we remove the clang warning's.
We are also make sure we are not passing any rogue values to lpc2000_iap_call.
Change-Id: Idb3b0077d1dae5f03dedab1d46d01140fe9ffb10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/777
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reorder to allocate all memory after COMMAND_PARSE_NUMBER call.
This removes a clang warning about un-released memory
Change-Id: I8dbeb664a6467077157015bd879bc0aefc5e8614
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/776
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the flash class was defined as FC_FLEX_RAM then this would always drop
through to the default handler.
This bug was found by clang, so untested.
Change-Id: I2d9fe6415dd216728a145519400f7b9ef1bd3c3a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/773
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Check that the target is valid before calling any target functions.
Change-Id: I538fccc79d5ec89976e14beab02cb20490b299bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/766
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
make distcheck is used to make packages with OpenOCD release, this
command uses information from Makefile.am files to know which files
should be included in the package and which can be left only in
repository. This patch makes a few headers from recent JTAG drivers
and one txt file with info about target tcl config files included in
released packages.
Change-Id: I91202290633a30f53624a8c7d9a0ebf72c40772b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/767
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Not just print it.
This enables scripts to analyze valuable config options of
arm946e-s cores, do internal BIST memory tests and more.
Be careful to flush caches before disabling it.
Do not forget that BIST test overwrites memory.
- cp15 rewritten from COMMAND_HANDLER to jim_handler.
Change-Id: I734da0be6db0a3127c2daa94ed75efef94da8ceb
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/694
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Cache type register C0.C is read-only, and display
hard core configuration information.
This information is unlikely be changed in runtime.
- removed C0.C access when result is not used in
arm946e_invalidate_dcache()
- access C0.C only once per target, store result
in cp15_cache_info field of target structure
- fix cache index count calculation
Change-Id: I12bc4c967fdf07f54d755f2f2f42406c0ababc1a
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/693
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Global variables 'dc' 'ic' had been used in the code
to keep target's state of D-cache and I-cache
on debug entry.
This may lead to incorrect operation in configurations
with multiple cores and unequal cache states.
Fix: move cache state to the appropriate bits of the
'cp15_control_reg' field (already present but unused).
Vaule of cp15 control register stored here on
arm946e_post_debug_entry(), and analyzed later
in arm946e_write_memory().
Change-Id: I71ef82be00c21d6fffb3726cec4974d1ece70dfe
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/692
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
For odd byte counts, stm32x_write() pads the last byte and writes it using
a discrete 16-bit access. The stlink debugger can't issue 16-bit writes so
it fails for odd byte writes.
This patch changes stm32x_write() to pad odd byte writes into a new buffer
and use the normal code path with a single block write. The fallback path,
when working area cannot be allocated, has to use 16-bit writes though
which means that sufficient working area is required for stlink and odd
byte writes.
Change-Id: I4c5dc456300b6e1056f76b0095be8aceee3e954f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/756
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
seems comments were mangled during the last cleanup.
Change-Id: If759f62032705c7baffd3973e9717eb7e8a5d17c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/752
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
When testing a pic32mx220f032b with different values
for adapter_khz and cpu clocks i was getting a lot of
corrupted data from the chip. From time to time
openocd fails with segmentation faults or is aborted
due to memory corruption.
Change-Id: I134743f75c477b3d55dc74ae4474598e153b4a4a
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/690
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Do not call mips32_cp0_read() if not needed.
This will speed up execution of mips_m4k_write_memory()
by near 2x, with parameter count = 1.
Change-Id: I7829a7802b6475bc6d4ac3f0632d8d239d1072da
Signed-off-by: Salvador <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Remove a lot of the repetitive code in stm32f1x flash probe by converting
the large if-selector to a switch, moving the common checks outside it and
concentrating the failure handling to a single point.
Do the same with stm32f2x and stm32lx for consistency.
Change-Id: Ic0ecfb1533c49f5d2108cda5fd20c8372d7c71ef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/746
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some variants read 0 for the flash size register, rather than
failing lets assume we have max flash fitted.
Change-Id: Ie1fb4e73606f49268a6fd5921c3aef75bc4790d3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/744
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rather than failing if the flash size reg cannot be read lets assume
we have the max flash size fitted.
It is quite common on early ST silicon to not correct support this register.
Change-Id: Ife058d60ae0027faad2c929ebd5b7fe2ef27234d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/743
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Revision X is not mentioned in the latest RM0038 rev5, however it has been
confirmed correct by ST using ST-LINK Utilty.
Change-Id: I65210e512ea25818a1d0d3b223502ebd7535b29d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/742
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
FT232H chips are new highspeed devices from FTDI. Basically these are a half of FT2232H (or a quarter of FT4232H), so only one channel which can be used as OpenOCD
interface. The chips are supported by libftdi 0.20 or later and by ftd2xx 2.08.12 or later.
Change-Id: Ic9a2c279167c3419a24f0d6befacbb83c4ffeb25
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/736
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
It's unnecessary and prevents reusing this function to fix
option byte writes.
Also try to disable flash writing after an error.
Change-Id: Ib5a7b768a1523e6b8da1555126fef4c1e60ab083
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/479
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The existing code tests the current debug_level for validity, allowing
the user to set it too high and never change it after that. The new
behaviour is to test the debug_level that the user has requested.
Change-Id: I85726a2e606c8d137e9b1cfe76fee865084844b1
Signed-off-by: Alan Bowman <alan.michael.bowman@gmail.com>
Reviewed-on: http://openocd.zylin.com/764
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This reverts commit e8641695c6
Original premise was wrong. Proper command is "shutdown", not "exit".
Change-Id: I07f5fe0dda9c24abe53628da986bfda0e406bb4a
Signed-off-by: Alex Austin <alex.austin@spectrumdsi.com>
Reviewed-on: http://openocd.zylin.com/757
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Based on ft2232.c but uses the MPSSE layer for low-level access, greatly
simplifying the JTAG logic. Remove all libftdi/FTD2XX code and all layout
specific code. Layout specifications are instead handled in Tcl.
Use a signal abstraction to enable Tcl configuration files to define
outputs for one or several FTDI GPIO. These outputs can then be
controlled using the ftdi_set_signal command. Special signal names are
reserved for nTRST, nSRST and LED (for blink) so that they, if defined,
will be used for their customary purpose.
Depending on the type of buffer attached to the FTDI GPIO, the outputs
have to be controlled differently. In order to support tristateable
signals such as nSRST, both a data GPIO and an output-enable GPIO can be
specified for each signal. The following output buffer configurations are
supported:
* Push-pull with one FTDI output as (non-)inverted data line
* Open drain with one FTDI output as (non-)inverted output-enable
* Tristate with one FTDI output as (non-)inverted data line and another
FTDI output as (non-)inverted output-enable
* Unbuffered, using the FTDI GPIO as a tristate output directly by
switching data and direction as necessary
The data and output-enables are specified as 16-bit bitmasks,
corresponding to the concatenation of the high and low FTDI GPIO
registers. To specify an unbuffered output, use the same bitmask
for both data and output-enable.
The adapter configuration file must also specify default values for the
FTDI data and direction GPIO registers, and the channel being used (if
different from 0).
Change-Id: I287a41d4c696cf5fc74eb10d5e63578b0dc7f826
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/452
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This is a higher-level libftdi replacement for use when implementing
protocol drivers for FT2232, FT2232H or FT4232H. It takes care of device
open/close and, unlike libftdi, also MPSSE command abstraction, command
queueing, buffer handling and return data parsing.
The FTDI device is accessed through libusb-1.0 in asynchronous mode.
Change-Id: I051adb574dcc39f8ca9cd7f6dbe6ae4aeea5f4c8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/451
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
Purely cosmetic but use the same style as Cortex-A target, this makes
searching refs easier.
Change-Id: I732ad9701f561e2312c5d191f5aaffd3a2f2393d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/731
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add missing arm cmd handlers that enable semi hosting support to work as
expected.
Change-Id: I063d82c48b82b4f6aed4efc4b08ea752d78e9047
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/734
Tested-by: jenkins
Reviewed-by: Alan Bowman <alan.michael.bowman@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
add support for the new stm32f3x family from stmicro:
http://www.st.com/stm32f3
Change-Id: Icd1db95bb2767d9c0ecef24deefa92b4fdaa4f14
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/735
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This cast to uint16_t is not (host) endianess save.
Depending on compiler usb_out_buffer[1] may be undefined.
Change-Id: If686e5d5da39541329c340bbdef472ee7ab0281c
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/732
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The ADIv5 spec guarentees that tar_autoincr_block will be 10bits.
Make this the default for Cortex-M family until we detect a Cortex-M3/M4,
we then change autoincrement to 12bits.
Change-Id: Ie8c89134aa036879bdd8a3c312cee9715dbc6913
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/730
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
openocd -f board/sheevaplug.cfg -c init -c exit
the calling shell will believe that openocd exited with an error due to exitval will be non-zero
This is not tested against incomming telnet
Change-Id: I63d15715a7b46f39a7de261a45039f8c3cad7a98
Signed-off-by: Stian Skjelstad <stian@nixia.no>
Reviewed-on: http://openocd.zylin.com/470
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
jim_target_md is supposed to print out results with command_print in
hexdump format. It was using command_print which appends a newline character
aftre every invocation. Using command_print_sameline instead
Change-Id: Iaff03021acc38d54b5a082cb58b82aa4449c0715
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/669
Tested-by: jenkins
Reviewed-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
- Added a few lines of comment before the function explaining the usage and the
output generated by the command
- Added a few lines of comment in the body explaining what is happening to improve
code readability
- Renamed a few variables to improve readability:
* a -> addr
* b -> dwidth
* c -> count
- Added a new variable, named byte to contain the number of bytes to read, instead
of overwriting the count parameter, to avoid confusion between the two values.
Change-Id: I5828ec0f5aadaa39becec7b84f198756bb2c3d41
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/665
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Interface drivers regularly need to keep track of where each part of a long
read buffer should be copied, once that data arrives. Both source and
destination are often at an arbitrary bit offset.
This queued bit-level copy can help with that, by allowing the driver to
perform postponed reads from the receive buffer already when building the
transmit buffer, and have those reads executed at a later time when data is
available.
For simplicity, it uses the linked list implementation list.h imported from
the Linux kernel.
Change-Id: I06862a0a6f057cbbcacfb021f17a795195faded2
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/450
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
New flash description for ATSAM3SD8C used on SAM3S-EK2 development boards. Name used
is "at91sam3sd8c" and chipid is 0x29ab0a60. Mirrors description of other similar parts.
Change-Id: I7fc4b82e7969451645ab067223663f08b76d866b
Signed-off-by: Mike Crowe <mpcrowe@gmail.com>
Reviewed-on: http://openocd.zylin.com/684
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
jtag_interface.transports field was left uninitialized, which triggers warning message
on program startup.
Although hardware natively supports SWD interface, no software support
currently present, so the value choosen to be <jtag_only>.
Change-Id: I2da41790b1850950af416cec4362d5b7bf927b2b
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/670
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In the previous iteration, the page counter for erases would not be updated with
the erase size. This patch keeps the page counter synced with the sector counter.
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Change-Id: I95e56a3257b2ad8301c9f28167b842fa6466334f
Reviewed-on: http://openocd.zylin.com/686
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For multi core cpus with cores without an idcode this doesn't work
because the extra bit for every core and a n-bit shift in the data
stream.
Change-Id: Iba0ad9422ea55c01492b27b936d028719be31180
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/618
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updates the Kinetis NOR flash support to handle all known block and sector
sizes. Previously only 2kiB sectors were hard-coded, now all four known
combinations non-volatile sector sizes are supported.
The premise of separating Kinetis Program Flash (PFLASH) from FlexNVM is
also introduced. This means each "block" of flash (in Freescale terms) is
treated as a bank in OpenOCD. Correspondingly, the existing board
configuration for the TWR-K60M512 eval system is updated to recognize two
banks instead of one.
A board config for the TWR-K60F120M is also added.
Bank and sector erase and programming has been checked with both of the
mentioned eval boards.
Change-Id: Iae2d10ebf8f548d0a3698df5430bbbe1ccadc58a
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/663
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some versions of Segger's software do not select JTAG interface by default.
Do it in the intial setup.
Firmware version check code still present, with updated set of unsupported.
Note from Segger:
Alright, we were not aware of that OpenOCD does not select the interface
before it starts communicating with the target. A debugger should always
select the appropriate target interface before it starts communicating with the target,
since otherwise it could also happen that a previous session with another debugger
had selected SWD and the interface was not switched again by OpenOCD.
Change-Id: I5b4eab7e0e3625ec32be75a36d89e16d17e899bf
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/667
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
jlink_usb_io() function added for basic communication,
since jlink_usb_message() is more specific to JTAG transactions.
To verify the patch issue "jlink config" command.
Change-Id: Id7d10bd5e8985d4c77f2e0ca47fb6033db2877bf
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/679
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
OpenOCD does not work with the latest firmware versions
of Segger J-Link.
Latest working version: V4.42c
Unsupported versions: 4.44 to 4.46f, 4.20 to 4.30
Older versions of firmware can be found here:
http://www.segger.com/j-link-older-versions.html
The firmware versions does not correspond directly with
"Software and documentation pack for Windows", it may be
distinguished by the "compile" date in the information string.
Print an warning message if unsupported firmware version detected.
Change-Id: Id7d1f965b8ce2fdbcd0026a85ddd093e2fa48720
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/666
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Removed the superflous call to Jim_GetResult,
as we are reading in the result to a variable
anyways in the next instruction.
Change-Id: Idc96400737dc15e28304e97bcea79fa6c7a88ae1
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/661
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems I5347352e7595686634bd0de13fcf6de6e55027b0 introduced an issue when
reading 8/16 bit data - the in buffer was always set to 32bits.
Change-Id: Ife2bb6a20fcb3ec0e486655512164f25ae9196b4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/660
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Call jtag_tap_add before LOG_DEBUG otherwise abs_chain_position does
not get correctly set.
Change-Id: I47bd00cc83259c8bfd5551e08c3bb2ebeb5993f5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/658
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
These events have been deprecated for a number of years, update any
remaining scripts to the new events.
Change-Id: Ic31ff388545ac8b3a500045699ca92c541b13f12
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/634
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
this header is used in numerous files and adding to config.h
simplifies its use globally.
Change-Id: Id724a9950b90504721233022c7fb5768e9bc5548
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/649
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This enables us to better handle some of the low level functions that the
stlink does not support. It also enables us to share a few more of the
standard cortex_m3 functions if necessary.
Change-Id: I7a2c57450122012ec189245d8879d8967913e00e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/637
Tested-by: jenkins
Use default_flash_blank_check, this will use the much faster
blank_check_memory handler if supported - 15x quicker on stm32f4.
Otherwise it will fall back to using the slower default_flash_mem_blank_check.
Change-Id: Ia231b3e95468c9e92594dbdbe1fa2d69e1506fc3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/632
Tested-by: jenkins
This makes the newer v2 api behave as per the v1 api, eg. single stepping
masks all interrupts.
A better long term solution is to use same behaviour as a cortex-m3
target, see CORTEX_M3_ISRMASK_AUTO.
Change-Id: Iaf9f9adf225cf274faaac938050bb996582aa98f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/621
Tested-by: jenkins
This enables the manual selection of the stlink api version.
Change-Id: I0ec8c5b0a101b6456f426d2fec65971da56db4e7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/617
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
The api v2 is supported on the stlink/v1 if it has a least v11 firmware.
Change-Id: Idfdb5a7f5a5881326017451ae9b6004eeaa46a96
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/616
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Some targets support connecting while the target's srst is asserted.
Tested on pic32 family.
Change-Id: I0d20c40af6d031d1306043893e95e61f484c0a87
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/608
Tested-by: jenkins
Some targets support connecting while the target's srst is asserted.
Tested on stm32 family.
Change-Id: I1197dd721a1e1cbf95ee77dfd8e1082b165b22a9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/607
Tested-by: jenkins
Some targets support connecting while the target's srst is asserted.
Tested on stm32 family.
Change-Id: I9df43623025e37832155aeee7aa099b844b85f16
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/606
Tested-by: jenkins
Marc Reilly
Spencer Oliver
Chuen Chou
Salvador Arroyo
Andreas Fritiofson
Freddie Chopin
Christopher Kilgour
Martin Nowak
Alexander Osipenko
Alan Bowman
Alex Austin
Stefan Mahr
Stian Skjelsad
Vandra Akos
Mike Crowe
Olivier Schonken
Mathias K
Mirela Tauciuc
Bill Traynor