The following warnings prevent OpenOCD from building:
efm32.c: In function 'efm32x_read_lock_data':
efm32.c:373:8: error: cast increases required alignment of target type [-Werror=cast-align]
efm32.c:386:9: error: cast increases required alignment of target type [-Werror=cast-align]
efm32.c:394:9: error: cast increases required alignment of target type [-Werror=cast-align]
efm32.c:402:9: error: cast increases required alignment of target type [-Werror=cast-align]
efm32.c: In function 'efm32x_get_page_lock':
efm32.c:430:17: error: cast increases required alignment of target type [-Werror=cast-align]
efm32.c: In function 'efm32x_set_page_lock':
efm32.c:441:19: error: cast increases required alignment of target type [-Werror=cast-align]
cc1: all warnings being treated as errors
This patch is compile-tested only.
Change-Id: Ia3a8f342e0f5e30c8ea4de9435c5c7a80bc100e3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1370
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Ensure FlexRAM usage is limited to half the FlexRAM size when programming.
Assume the FlexNVM sector size is equal to half the FlexRAM.
Fix sector erase checking which had an error introduced when the
kinetis_ftfx_command( ) signature was changed.
Change-Id: I88edd9c7d4a4ba474cad7b00052feaeedfa8ced8
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/1358
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This patch adds flash programming support for internal flash of the
LPC43x2/3/5/7 part, tested on a LPC4337 (also tested on a LPC1768
and LPC2468). It should also work with LPC1800's with onchip flash.
The "base" parameter of the "flash bank" command is now significant
for the lpc4300 variant and required to determine the bank number
parameter needed by the IAP routines.
NOTE: I could only program flash successfully when the chip is powered
with "P2_7" pulled low to put it in ISP mode. When running from flash
(and not the ISP ROM), the target fails to halt and the sector erase
fails. This is similar to the behavior I remember when trying out the
spifi driver on a LPC4350... lots of power cycles to make progress, one
To burn, one to run. So I am not confident my config is set up correctly.
Change-Id: I8a75ef1b95cedd5b5898b2dedff477f502fd19f3
Signed-off-by: Matt Dittrich <mdittrich.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1126
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
The em357 driver only supported one page configuration (192k in 96 2048k)
pages. This is fine for em357 chips since that's the size they have, but
ST's STM32W chips (pretty much the same) have different flash
configurations available (64, 128, 192, 256k). I can't find anywhere
that would indicate the size of the chip anywhere in memory so the
selection must be manual, using the 'size' parameter. For backwards
compatibility, any size not known to be in use defaults to the 192k
configuration. I don't have any em357 devices to test, but I also found
that I had to re-assert the FPEC clock enable before performing an
erase. This is a single line and shouldn't break any configurations.
My testing so far has only been with a 64k device with 8k of RAM.
Change-Id: Ic0ac400a9696efaa09d1407dd4a4d456bc2c318b
Signed-off-by: Ben Nahill <bnahill@gmail.com>
Reviewed-on: http://openocd.zylin.com/1336
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Disable polling the target before we issue a 'reset run'. This stops errors or
warnings if the target disables the SWD or JTAG interface as part of the
application code.
Change-Id: I5019dffdad41a8e210003ece1caf89069ee0f223
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1331
Tested-by: jenkins
Added support for ARMv7-M targets in arm_nandwrite and
arm_nandread.
Change-Id: Iab1d78d401f735e191c6a8519f3619035a300fae
Signed-off-by: Henrik Nilsson <henrik.nilsson@bytequest.se>
Reviewed-on: http://openocd.zylin.com/1188
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The command 'at91sam3 info' ignores PLLA DIV values >1. This patch fixes it.
Tested on a SAM3S4C chip.
Change-Id: I051f41bb3dcefe1ac785fbcb48477a807daa16a2
Signed-off-by: Thomas Schmid <thomas.schmid@gmail.com>
Reviewed-on: http://openocd.zylin.com/1307
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The only caller was arm_nandwrite(). Replace that call with
target_write_buffer() instead, which in turn may end up calling the same
bulk_write_memory target API function.
Change-Id: If34c7474df5cf14af3b732fb4774816818f28e79
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1214
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The kinetis datasheets specify the flash registers as bytes rather
than as words, as the previous implementation did. This also makes
a few code sections slightly less endian-magical.
Change-Id: If8f4adfc7f4341085ae5b6eacbf7d74bbd74cf08
Signed-off-by: Alex Austin <alex.austin@spectrumdsi.com>
Reviewed-on: http://openocd.zylin.com/1192
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a program proc that simplifies using OpenOCD as a standalone
programmer.
Change-Id: I6ece492cd878c170b734e8bb2e09fe8c4557d5a6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1199
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes an issue if the device is manually probed after the initial probe
fails due to being unable to read flash size register. In this situation the
driver assumes the user has overridden the flash size when infact this may
not be the case.
It also seems on the older stm32f1 devices the flash register is not readable
when locked, this does not seem to apply to the newer parts - f0, f3, f4.
Change-Id: I125f872fcb2d962ca6705f97b62d957e2b31303b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1187
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stm32f0 and stm32f3 share the same option byte location, but the format
differs.
Adding an option_offset fixes the broken options_read cmd and incorrectly
setting Hardware Watchdog when unlocking a f3x device.
Change-Id: I82d66b6198294ea9eedb44ca8b2fb368c0cb15e8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1184
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added support for new ST devices in the stm32lx portfolio, with device
id 0x427. These have 256k flash, but in a single bank compared to
device id 0x436 which is a dual bank flash.
Change-Id: Iafdfe990f24bd04b0d6e00385ee70690f3bf8d5f
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1140
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update adds support for the STM32Lx 384kb dual bank flash. Previously there was a problem when writing an
image that was larger than 192Kb. That lead to openocd printing out two error messages like
"Error: access denied / write protected" and "Error: invalid program address". The reason was that the stm32lx
driver tried to write half pages which overlapped into the next flash bank.
A new configuration file stm32lx_dual_bank.cfg can be used for stm32lx chips with dual bank flash (256kb or 384kb devices).
A sanity check was added for probed flash size values to fix the issue seen on some ST samples that answered incorrectly.
Change-Id: I69e25131983d88613be8606b438f98870c5f1e52
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It has been seen on some stm32 targets that the flash size register that
is probed by the driver may contain an invalid size.
This change enables the user to override the probed value.
Change-Id: I09359e59a96f9133d3d939670957d32a830a944e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1132
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
This makes sure we are using privileged mode when executing any loaders.
Change-Id: I18bf32ec92e1c76a66ab25e3712652bc3650b332
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1108
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
To simplify things change over to using the generic core_mode struct rather
than maintaining a armv7m specific one.
Change-Id: Ibf32b785d896fef4f33307fabe0d8eb266f7086f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/966
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
An issue has been seen with the stm32lx flash driver that if a
power cycle/reset is applied after a erase, any ram loader will Hard Fault
on execution.
A similar issue is mentioned in the errata for the device.
Two solution's seem to workaround this issue:
1, Handle the exception, this means adding exception vectors to the loader
and changing the exception address using nvic vtor register.
2. falling back to using slower direct page writes - approx 50% slower.
Using solution 1 would mean restrictions are placed on the loader location.
Solution 2 was chosen mainly as it was simpler too implement.
Change-Id: I429f06b5a3e3b1d8de90071a88a7df11fc9b46a7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1010
Tested-by: jenkins
Waiting 20secs is a bit much excessive, we could probably reduce to 5.
Change-Id: Iffb97adb99c2541a075fe78dbc88a53ddf340214
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1009
Tested-by: jenkins
Handle any leading bytes upto the next 128 byte page, enabling us to safely
use the faster page write.
Rather than use a separate word/byte write to program any trailing bytes
we use a combined write function.
Use memcpy for byte writes and change loader to using bytes.
Change-Id: Ie0164a30388f018dd00e752cf5ff87d4f96ced97
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1008
Tested-by: jenkins
Fixed flash page size detection according to EFM32 GG/LG errata.
MEM_INFO_PAGE_SIZE register containts invalid value in devices with
revision number lower than 18 and should not be used.
Change-Id: Idb2832246efcbbec2fd98a5c458f72a36df386fb
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1116
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently we have to supply the arg's to this cmd in a set order, this
change fixes that issue.
Change-Id: I14a15732e1917a91009e1ac14fba39ca1523c739
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/992
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Make sure we do not mask out the BFB2 boot bank bit, as this is used on
the larger XL devices.
Change-Id: Iacfdf874140e409e0c4ca9b9aee8f5c2f90dc9be
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/991
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The STM32F0 and F3 devices use a different default RDP to configure a
unlocked device, make sure we use that.
Change-Id: I170779461412c4c202c2cfc8d90baedb7e388150
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/984
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The user is able to use 2bytes of the options byte data for whatever
purpose they wish. Make sure we preserve this during an option erase/write.
Change-Id: Ibf951b11c59a148e671b1eb47fdc9b4f49ccae15
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/983
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Some debuggers (stlink) can't issue 16 bit writes and have to use a
loader to write flash memory.
Currently the loader is not used for option bytes, causing
stm32x_write_options to fail silently on such hardware.
Fix this by using stm32x_write_block to write option bytes as well.
Change-Id: I49c29d53ab5e162463cb349d4c89bef96467e587
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/480
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The current stm32lx driver will fail if no working area is
provided - fallback to using slow writes if this is the case.
Change-Id: I92b1535fec4aebc855c63ce2c54b10f168f3c07e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1007
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updated as per ST RM0033 rev 5
Change-Id: I627fdab69b440b75b8e4f7c474216538fa5273a4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1001
Tested-by: jenkins
Other than a larger memory layout these new devices also have an extra
MER1 bit to perform the mass erase.
Change-Id: I7110a05bac95c1707160d1f5622181664291eb4a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/985
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Added in spi device table SPI Flash Winbond W25Q64CV 64Mbit
Its Device ID 0x001740ef is the same as Spansion S25FL064K (may
be a clone?)
Change-Id: I3cdbd182a0ccde75c78684cb9d54c76059bf34e0
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/928
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems ST have changed the ref manual (RM0313 rev1) and reverted to using
letters rather than numbers for the stm32f3x family.
Change-Id: I3a87ec9b0b2447d57dfef98603d30e28fe9ac927
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/926
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
Flash algorithm for LPC17xx/LPC2xxx was trying to "reuse" previously
allocated working area on next flashing which is not possible -
working areas are freed automatically on reset. This caused all but
first flashing attempts to fail. As there is no point in storing pointer
to working area, it was converted to local variable.
Change-Id: I939946325ff9eecc4861c0f51ab0f73871a3d7b9
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do some cleanup in lpc2000.c - concatenate short lines into single
longer lines, move variable declarations to "just before" they are
used, etc.
Change-Id: Ia7b9f0307dd4857ee8e15c8a6d4d7b5c4392fd80
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/861
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
No change to code, just fix some formatting issues.
Change-Id: I177430a99bfecbf90a1ddf623321c29d4db516b0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/906
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The erase time for the option byte page is not directly specified but is
assumed to be the same as the other pages (or mass erase) which is 20 to
40 ms. The current timeout value is 10 which means 10 ms plus the time to
poll the status flag that many times.
With faster interfaces or drivers (such as when using the ftdi driver
instead of the ft2232 driver) the adapter delay is not enough in some
cases, unless the jtag freq is reduced as a workaround. The result is a
"timed out waiting for flash" error when trying to write the options.
Increase the timeout to a minimum of 100 ms, which is in line with the
other erase timeouts. Also make defines of both the erase and the program
timeouts.
Change-Id: Ia86e71505033c52b60ef30092000689fbb547a18
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/902
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The pointer must be non-null here since we returned if allocation failed.
Change-Id: I9b75099ed3b3870c815d1df5760ed1f3fe1d20d6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/866
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Spencer Oliver
Paul Fertser
Christopher Kilgour
Freddie Chopin
Matt Dittrich
Ben Nahill
Peter Dietzsch
Henrik Nilsson
Thomas Schmid
Andreas Fritiofson
Alex Austin
Johan Almquist
Roman D
Szymon Modzelewski
Muranaka Masaki
Gianluca Renzi