stlink v2 on Nucleo-64 board (e.g. NUCLEO-L476RG) has target SWO signal
connected to STM32F103CB'S PA10, which is UART1_RX. UART1 within this
MCU in theory can be configured to 4.5 Mbps baudrate, which means this
is the upper limit supported by HW. As a confirmation BMP (Black Magic
Probe) project also states in documentation that UART1 can be used with
up to 4.5 Mbps baudrate.
Tests have shown that configuring 4.5 Mbps baudrate on stlink v2
available on NUCLEO-L476RG board results in receiving corrupted data.
Using 2.25 Mbps however allows to successfully receive all data from
SWO. This makes sense in terms of STM32F103CB capabilities, since 2.25
Mbps is the next supported baudrate due to division by 2.
Increase supported stlink v2 SWO speed from 2 to 2.25 Mbps.
Tested with NUCLEO-L476RG:
$ stm32l4x.tpiu configure -protocol uart \
-traceclk 80000000 -pin-freq 2250000 \
-output /dev/stdout
$ stm32l4x.tpiu enable
2.25 Mbps speed confirmed with logic analyzer.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Change-Id: Icbec04585664aba8b217e8f9a75458e577f7617f
Reviewed-on: https://review.openocd.org/c/openocd/+/7848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This emulation mode supports software translation of an AP request
into an address mapped transaction that does not rely on physical AP
hardware. This is necessary in some hardware such as K3 SoCs since the
hardware architecture anticipates a potential race condition between
AP doing direct memory access generating transactions back to system
bus and firewalls that data path out.
This emulation mode allows direct memory driver to emulate CoreSight
Access Port (AP) and reuse the SoC configuration meant for JTAG
debuggers.
Since the address ranges are flat in nature, the requisite memory base
and size will need to be provided a-priori to the driver for mapping.
The other design alternative would be to map requested memory map for
every register operation, but, that would defeat our intent of getting
max debug performance.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I2d3c5f7833f1973e90b4f6b247827f62fc2905d0
Reviewed-on: https://review.openocd.org/c/openocd/+/7089
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Direct memory driver support for CoreSight Access Port(AP).
Even though we emulate SWD (serial wire debug), we aren't actually
using swd. Instead, we are using a direct memory access to get to the
register set. This is similar in approach to other fast access native
drivers such as am335xgpio drivers.
Example operation on Texas Instrument's AM62x K3 SoC:
+-----------+
| OpenOCD | SoC mem map
| on |--------------+
| Cortex-A53| |
+-----------+ |
|
+-----------+ +-----v-----+
|Cortex-M4F |<───────| |
+-----------+ | |
| DebugSS |
+-----------+ | |
|Cortex-M4F |<───────| |
+-----------+ +-----------+
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I8470cb15348863dd844b2c0e3f63a9063cb032c6
Reviewed-on: https://review.openocd.org/c/openocd/+/7088
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add basic connection details with am625 SK/EVM
For further details, see https://www.ti.com/tool/SK-AM62A-LP
Change-Id: I0b6b4004f3a04be7a90207e44c588a4f68aff47a
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7855
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add support for the TI K3 family AM62A7 SoC.
For further details, see https://www.ti.com/lit/pdf/spruj16a
Change-Id: Ie69bde4895f34b04f9967f63d1ca9c8149c50b8a
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7854
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add links for the SoCs are supported by the conf file for future
reference.
Change-Id: Ic5b7786ef3ac31414fe2ce56c1237a18ce99aaa1
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7853
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since zephyrproject-rtos/zephyr@c3eeae8,
Zephyr OS exposes offset of mode_exc_return in the arch struct for ARM.
Accounting for this allows for consistency and enables
logic with further offsets that may be added after this.
Signed-off-by: Bruno Mendes <bd_mendes@outlook.com>
Change-Id: Id53ebd80c5d98a7d94eb6b00ad638ce51e719822
Reviewed-on: https://review.openocd.org/c/openocd/+/7851
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Sufficient to probe both cores via multiple APs.
No support listed for jtag in the datasheet or usermanual.
Tested against a BW-16 board:
https://www.amebaiot.com/en/amebad/#partner_bw16
Change-Id: Idf82085e7b7327fdf3d6d668e6fb59eff6e0431b
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7847
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
These cores are advertised as M23 and M33 compatible, but are identified
by the Realtek implementor id. These cores are found on the RTL872xD
family, at least.
Raw CPUIDs:
Real-M200 (KM0): 721cd200
Real-M300 (KM4): 721fd220
Change-Id: I4106ccb7e8c562f98072a71e9e818f57999d664e
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Presently, we only look at the Part Number field of the CPUID, and
completely ignore the Implmentor field, simply assuming it to be ARM.
Parts have since been found, with different implementors, that use
overlapping part numbers, causing detection to fail.
Expand the "part number" field to be a full implementor+part number,
excluding the revision/patch fields, to make checking more reliable.
Change-Id: Id81774f829104f57a0c105320d0d2e479fa01522
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7845
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There's really no reason to try and add an extra layer of cpu
verification here.
Change-Id: If8c4aa03754607be6c089f514ae300b09b067ffa
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7844
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use blocks (64 KiB) instead of sectors (4 KiB) when erasing the zd25Q16
SPI flash memory (thanks to Tomas Vanek!)
Change-Id: I969a69ad35f51b84eb3e11b93f0d79db3e98613a
Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org>
Reviewed-on: https://review.openocd.org/c/openocd/+/7850
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add missing aarch64_poll() calls to ensure the event
TARGET_EVENT_HALTED is called when necessary.
This is needed with the poller update introduced in commit
95603fae18 ("openocd: revert workarounds for 'expr' syntax change")
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Change-Id: I6e91f1b6bc1f0d16e6f0eb76fc67d20111e3afd2
Reviewed-on: https://review.openocd.org/c/openocd/+/7737
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit provides startup files for the Synopsys DesignWare ARC
HSDK-4xD board. These have been adapted from the corresponding
snps_hsdk.cfg files, the only functional change being the JTAG IDs for
the new board's CPU cores.
Change-Id: I19a0cd13bc09de90cfe2a7cccf1239e459fd8077
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7829
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This is ANGIE's firmware and bitstream code.
The 'Embeded C' code is based on the openULINK project.
The hdl bitstream source code is for the spartan-6 FPGA included in
ANGIE.
Since ANGIE has a different microcontroller (EZ-USB FX2) than openULINK
(EZ-USB AN2131), the registers file (reg_ezusb.h) has been changed
completely, so are the descriptors, interruptions and the endpoints
configuration.
Change-Id: I70590c7c58bac6f1939c5ffba57e87d86850664d
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7701
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The USB control transfer can be executed without any data.
The libusb API libusb_control_transfer() can thus be called with
zero 'size', thus returning zero byte transferred when succeed.
The OpenOCD API jtag_libusb_control_transfer() returns zero either
in case of transfer error and in case of libusb_control_transfer()
returning zero, making impossible discriminating the two cases.
Extend jtag_libusb_control_transfer() with separate return value
for error code and explicit parameter's pointer for transferred
bytes.
Make the transferred pointer optional, as many callers do not
properly handle the returned value.
Use 'int' type pointer for transferred, instead of the 'uint16_t'
that would have matched the type of 'size'. This can simplify the
caller's code by using a single 'int transferred' variable shared
with other jtag_libusb_bulk_read|write, while keeping possible the
comparison int vs uint16_t without cast.
This change is inspired from commit d612baacaa
("jtag_libusb_bulk_read|write: return error code instead of size")
Change-Id: I14d9bff3e845675be03465c307a136e69eebc317
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7756
Tested-by: jenkins
Reviewed-by: ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Add the full text of the LGPL 2.1 license to OpenOCD. It was
copied directly from:
https://spdx.org/licenses/LGPL-2.1.html#licenseText
Add the required tags for reference and tooling.
Checkpatch-ignore: FSF_MAILING_ADDRESS
Change-Id: I081f2197fb3c60e17cd6e3353d38194c720ee8a3
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7743
Tested-by: jenkins
Reviewed-by: ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
This patch changes data types of watchpoint value and mask to allow for
64-bit values match that some architectures (like RISCV) allow.
In addition this patch fixes the behavior of watchpoint command to
zero-out mask if only data value is provided.
Change-Id: I3c7ec1630f03ea9534ec34c0ebe99e08ea56e7f0
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7840
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
register_cache_invalidate() is written a way which uses
pointer arithmetic, which makes it harder to read. This patch
replaces it with more readable way to iterate over array of
structs.
Change-Id: Ia420f70a3bb6998c690c8c600c71301dca9f9dbf
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7735
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Lot of messages was logged as LOG_WARNING, but the operation failed
immediately. Sometimes no error message was logged at all.
Add missing messages, change warnings to errors.
Sometimes ERROR_TARGET_INVALID was returned. Some command handlers
returned ERROR_OK! Always return ERROR_TARGET_NOT_HALTED.
While on it use LOG_TARGET_ERROR() whenever possible.
Prefix command_print() message with 'Error:' to get closer
to LOG_TARGET_ERROR() variant.
Error message was not added to get() and set() methods of
struct xxx_reg_type - the return value is properly checked and a message
is logged by the caller in case of ERROR_TARGET_NOT_HALTED.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I2fe4187c6025f0038956ab387edbf3f461c69398
Reviewed-on: https://review.openocd.org/c/openocd/+/7819
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Compiler would complain that `written` was used without being
initialized.
Simplify the code a little. The number of bytes written is already
checked in usb_write().
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Ibada85dcccfca6f1269c584cdbc4f2e3b93bb8f3
Reviewed-on: https://review.openocd.org/c/openocd/+/7813
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
While not affecting the function's main purpose, an error has
crept into arc_save_context() that results in logging wrong register
values when the debug level is 3 or more. For instance, when debugging a
trivial program and halting at entry to main, the following values are
printed to the log:
Debug: 2915 2020 arc.c:894 arc_save_context(): Get core register regnum=0,
name=r0, value=0x0000000
...
Debug: 2947 2020 arc.c:894 arc_save_context(): Get core register regnum=60,
name=lp_count, value=0x900002d8
Debug: 2948 2020 arc.c:894 arc_save_context(): Get core register regnum=63,
name=pcl, value=0xffffffff
Debug: 2949 2020 arc.c:909 arc_save_context(): Get aux register regnum=64,
name=pc, value=0x900000b4
Debug: 2950 2020 arc.c:909 arc_save_context(): Get aux register regnum=65,
name=lp_start, value=0x900000bc
Debug: 2951 2020 arc.c:909 arc_save_context(): Get aux register regnum=66,
name=lp_end, value=0x00080801
Debug: 2952 2020 arc.c:909 arc_save_context(): Get aux register regnum=67,
name=status32, value=0xffffffff
After the change, the register contents make much more sense:
Debug: 2923 3934 arc.c:889 arc_save_context(): Get core register regnum=0,
name=r0, value=0x00000000
...
Debug: 2955 3934 arc.c:889 arc_save_context(): Get core register regnum=60,
name=lp_count, value=0x00000000
Debug: 2956 3934 arc.c:889 arc_save_context(): Get core register regnum=63,
name=pcl, value=0x900002d8
Debug: 2957 3934 arc.c:903 arc_save_context(): Get aux register regnum=64,
name=pc, value=0x900002da
Debug: 2958 3934 arc.c:903 arc_save_context(): Get aux register regnum=65,
name=lp_start, value=0x900000b4
Debug: 2959 3934 arc.c:903 arc_save_context(): Get aux register regnum=66,
name=lp_end, value=0x900000bc
Debug: 2960 3934 arc.c:903 arc_save_context(): Get aux register regnum=67,
name=status32, value=0x00080801
While at it, simplify a couple of expressions.
Change-Id: I8f2d79404707fbac4503af45b393ea73f91e6beb
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7765
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Board config file for ESP32-S3, to allow communication with
the builtin USB-JTAG adapter.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1310f5db30f7df38fe9344f7ba2334611b53863e
Reviewed-on: https://review.openocd.org/c/openocd/+/7749
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This config file enables communication over USB-JTAG with
ESP32-C3, ESP32-S3, ESP32-H2 and ESP32-C6 chips
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Iceea26972588d8c4919d1f3248684ece48ca9121
Reviewed-on: https://review.openocd.org/c/openocd/+/7748
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory region addresses are not in use for now.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9a2189e956ae59b56245ec914ab16719df857b2d
Reviewed-on: https://review.openocd.org/c/openocd/+/7762
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Right after target halt, some activities needs to be done
such as printing exception reason, disable wdts and reading
debug stubs information.
Missing activities will be submitted in the next patches.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I27aad5614d903f4bd7c8d6dba6bfb0bdb93ed8dc
Reviewed-on: https://review.openocd.org/c/openocd/+/7757
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ifb0122f3b98a767f27746409499733b70fb7d0e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I36c86fe4ebc99928ce48a5bff8cb9580a0fa3ac0
Reviewed-on: https://review.openocd.org/c/openocd/+/7746
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9181737d83eeba4e983b6a455b8a1523f2576dd2
Reviewed-on: https://review.openocd.org/c/openocd/+/7745
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Consolidate commonly used commands and variables from
chip config files into functions in esp_common.cfg.
This includes "jtag newtap," "target create,"and "configure -event."
Enhances code reusability and simplifies maintenance.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9e8bf07a4a15d4544ceb564607dea66837381d70
Reviewed-on: https://review.openocd.org/c/openocd/+/7744
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
See section 57.6.1 in RM0432.
Change-Id: Ic4977aee74d1838f420c1d9ff19925d09f8f6e2b
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add more ultrascale devices. Set instruction codes for SSI devices
such that refresh/program read_stat and user registers will work.
Change-Id: Id0a0706f4016eb8a4732725a5b72ae61efd73421
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7716
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Adding a single file for each different ir-length.
Change-Id: Iba3dd55b91c28fdb4d0cafa1ededd939fe61a267
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7715
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Marcin Niestroj
Kaelin Laundry
Nishanth Menon
Jason Peck
Jason Kacines
Bruno Mendes
Karl Palsson
Nikolay Dimitrov
Daniel Anselmi
Daniel Goehring
Artemiy Volkov
gudvinr
Ahmed BOUDJELIDA
Antonio Borneo
Thomas Gleixner
Parshintsev Anatoly
Marek Vrbka
Tomas Vanek
Tim Newsome
eolson
Erhan Kurubas
Marc Schink
Laurent LEMELE