Add option "nvmuserrow" to "at91samd" for changing and reading the register at 0x804000 which represents various fuses.
Change-Id: I6382cc4ac15e6b9681e2f30b0ae60397a6289c3b
Signed-off-by: Stefan Arnold <sarnold@sh-sw.de>
Reviewed-on: http://openocd.zylin.com/4260
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
HWID originally added in commit 7829f31a6d
was accidentally omited during refactoring in commit
52885d2b53
While on it move old ingeneering sample of 51822 to block of 51822 rev 1
Change-Id: Ie9f15563792a27a72e71df6edbcc6b04490370ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4437
Tested-by: jenkins
KitProg firmware does not send a zero length packet at the end of the bulk-in
transmission of a length divisible by a bulk packet size. This is inconsistent
with the USB specification and results in jtag_libusb_bulk_read()
waits forever when a transmission of specific size is received.
Limit bulk read size to expected number of bytes for problematic tranfer sizes.
Use 1 second timeout as the last resort.
Change-Id: Ice80306424afd76e9fbc6851911ffd5109c84501
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4426
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Avoid ever overflowing the DWT_COMPARATOR array by allocating space for
16 comparators (the field is masked by 0xf).
On a stm32f767zi chip (on a nucleo-767zi board) I've been seeing crashes
with address sanitizer enabled due to its (apparent) 10 present
comparators. This appears to be due to
https://sourceforge.net/p/openocd/tickets/178/.
In non-address sanitizer builds, this would likely cause some random
memory to be written to in some cases. (see above bug for observations).
Change-Id: I2b7d599eb326236dbc93f74b350c442c9a502c4b
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4458
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All drivers which simply allocate one driver_priv memory block
per each bank now use default_flash_free_driver_priv()
Change-Id: I425bf4213c3632f02dbe11ab819c31eda9b2db62
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4417
Tested-by: jenkins
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This works around some side effects of the -rtos hack, namely that we
were unable to set hardware breakpoints on harts whose misa differed
from the first one. There may be other bugs like this one lurking
elsewhere. The only proper solution is for gdb to have a better user
interface when talking to a server that exposes multiple targets, but
that's a very big project.
This fixes#194.
Change-Id: I81aedddeaa922d220e936730e9c731545953ae21
This replaces the earlier mechanism which would propagate errors only
for targets that decided they wanted to. It was suggested by Matthias
Welwarsky from the OpenOCD team.
Change-Id: Ibe8e97644abb47aff26d74b8280377d42615a4d3
Also call adapter_exit() before command_exit() as the latter releases
Jim interpreter so JTAG events should be released before.
Fixes memory leak reported by valgrind
Change-Id: I493f3fcba34ea2b4234148e79a4e329c866e0f05
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4474
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If a target is run from gdb and then stopped from OpenOCD telnet interface,
halt does not show message with status and PC registers.
While on it rename 'display' to 'verbose_halt_msg' and use bool type
instead of int.
Change-Id: Ibe6589015b302e0be97258b06938c297745436a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4475
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
provide meta information for the cpsr so gdb can display the status
flags and not only a hexadecimal number
Change-Id: I9d3fb29153780adbea389d7e4175d5e19bddc256
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4460
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
a bitfield may carry a type (bool or int), add support for that.
Change-Id: Ic831a9b8eac8579e8fdd7d0f01b7f1c9259e6739
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4459
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
and move declaration of all transport_is_xxx() functions to transport.h
Change-Id: Ib229115b5017507b49655bc43b517ab6fb32f7a6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4469
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This allows a user to tell OpenOCD to prefer system bus access for
memory access, which can be useful for testing, or when there really is
a difference in behavior.
Change-Id: I8c2f15b89a2ccdae568c68ee743b75a74f9ad6bd
Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.
If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.
Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If we enter debug state from EL0, some registers are not accessible.
Temporarily move to EL1H and back to gain access. Also, fix
armv8_dpm_modeswitch() to not immediately restore the previous state
on elevating the privilege level.
Change-Id: Ic2a92109230ff4eb6834c00ef544397a5b7ad56a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4461
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
gdb assumes that a rtos can make any thread active at will in response
to a 'Hg' packet. It further assumes that it needs to step-over after
setting a breakpoint on frame #0 of any non-current thread. Both
assumptions are not valid for an actual rtos. We fake the step-over to
not trigger an internal error in gdb. See
https://sourceware.org/bugzilla/show_bug.cgi?id=22925 for details.
Change-Id: Ida60cd134033c1d58ada77b87fe664a58f61e2c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4448
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Normally, when a ctrl-c is received from gdb, a SIGINT is reported back
unconditionally to tell gdb that the target has stopped in response.
However when a rtos support was configured, the rtos awareness overwrote
the signal with an actual thread state, which gdb then ignored and got
stuck without the user able to interrupt.
Change-Id: I40fd62333e020a8c4d9df0079270e84df9c77f88
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4445
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Also uses calloc() for mpsse_ctx->write_buffer to prevent a false
positive valgrind report
"Syscall param ioctl(USBDEVFS_SUBMITURB).buffer points to uninitialised bytes(s)"
Change-Id: I91963371d15c21ea0fee4c40c1da86174db44520
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4418
Tested-by: jenkins
Although the leak is negligible, the clean heap on exit will ease
valgrind testing.
Change-Id: I3a7a9c8e8dc7557aa51d0b9caa244537e5e7007d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4410
Tested-by: jenkins
If OpenOCD command line contains -c shutdown, server_quit() is not called.
Though if -c init is also on command line, gdb_server is already initialized.
Call server_quit() on both successful and failure exit from command line.
Change-Id: I6df41c5df045b61d84a5515d1abaa5dc96bc30ac
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4409
Tested-by: jenkins
Since BLX in Thumb2 always switches mode to ARM, the PC needs to be
4-bytes aligned.
Change-Id: I4f4c194fe21093cecfd9872e1d30588f4adc7257
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4382
Reviewed-by: Philipp Guehring <pg@futureware.at>
Tested-by: jenkins
Reviewed-by: Paul Sokolovsky <pfalcon@users.sourceforge.net>
Change occurrences of char to uint8_t where appropriate as a binary
protocol is used to talk to this adapter.
This fixes a build issue with modern clang.
Change-Id: I21cc82c8cad148bd0977533c12c74a9d6ba2faff
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4462
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This is a second try for this patch. I removed the queues from the
previous version. I made it compatible with SRST reset and added
support for those features that could be supported in raw binary
mode.
Change-Id: I96fc06abbea9873e98b414f34afd9043fd9c2a41
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/3960
Tested-by: jenkins
Reviewed-by: Eric Work <work.eric@gmail.com>
Reviewed-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jacob Alexander <haata@kiibohd.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Create new command to refresh idcode list during runtime
and update Tap idcode.
Change-Id: Ie889a39a6f57cea207b2b9c9e42c51c97cfe4d8e
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/4133
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: penny chen <penny6610231@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without this, we have some types promoted to `int` when they need to be
`unsigned int`.
Here's some ubsan output hitting this:
Unfortunately, what happens is that things get promoted to `int`, but
need to be `unsigned int`. Here's the ubsan output:
src/helper/types.h:126:65: runtime error: left shift of 255 by 24 places cannot be represented in type 'int'
#0 0x55978a612060 in le_to_h_u32 src/helper/types.h:126
#1 0x55978a61ff9e in stlink_usb_read_reg src/jtag/drivers/stlink_usb.c:1539
#2 0x55978a8cfd45 in adapter_load_core_reg_u32 src/target/hla_target.c:67
#3 0x55978a9f48e3 in armv7m_read_core_reg src/target/armv7m.c:236
#4 0x55978a8d24fc in adapter_load_context src/target/hla_target.c:372
#5 0x55978a8d261b in adapter_debug_entry src/target/hla_target.c:396
#6 0x55978a8d3123 in adapter_poll src/target/hla_target.c:457
#7 0x55978a528357 in target_poll src/target/target.c:535
#8 0x55978a539fd4 in target_wait_state src/target/target.c:2914
#9 0x55978a556e20 in jim_target_wait_state src/target/target.c:5256
#10 0x55978a5cca62 in command_unknown src/helper/command.c:1030
#11 0x55978aaed894 in JimInvokeCommand /home/cody/d/openocd-code/jimtcl/jim.c:10364
Change-Id: I24f6abfd26b6980100657397d69c84f2b80a005a
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4455
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Instead of re-reading ttbcr and ttb0/1 whenever a virt2phys translation
is done, cache the values once when entering debug state. Use the cached
values in armv7a_mmu_translate_va().
Change-Id: I1bc5349ad2f19b2dd75bdd48468a2c1f1e028699
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3112
Tested-by: jenkins
This patch adds support in openOCD to read/write Arm vector/floating
point registers. This is compatible with Arm vfp v3 target xml in GDB.
Please refer to binutils-gdb/gdb/features/arm/arm-vfpv3.xml
Change-Id: Id4dd1bddef51c558f1a86300c1a876d159463f18
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4421
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
Tim Newsome
Stefan Arnold
Tomas Vanek
Cody P Schafer
Michele Sardo
Matthias Welwarsky
Paul Fertser
Matej Kogovsek
Mateusz Manowiecki
Hellosun Wu
Matthias Welwarsky
Omair Javaid